Search results

This paper aims to characterize the surface film formed on Alloys 800 and 690 in chloride and thiosulfate-containing solution at 300°C.

Alloy 800 and 690 were immersed in chloride and thiosulfate-containing solution at 300°C up to five days, and then the surface film was analyzed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and energy dispersive X-ray spectrometers (EDX).

Through static immersion experiments in a high-temperature and high-pressure water environment, the alloy samples covered by surface film after five days of immersion were obtained. The morphology of the surface film was characterized at both horizontal and cross-sectional scales using SEM and focused ion beam-TEM techniques. It was observed that due to the influence of the quartz lining, the surface film primarily exhibited a bilayered structure. The first layer contained a significant amount of SiO₂, with a higher content of metal hydroxides compared to metal oxides. The second layer was predominantly composed of Fe, Ni and Cr, with a higher content of metal oxides compared to metal hydroxides.

The results showed that the materials of the lining of the autoclave could significantly influence the film composition of the tested material, which should be paid attention when analyzing the corrosion mechanism at high temperature.

The purpose of this paper is to clarify the influence of low earth orbit space environment on the wear mechanism of TC4 alloy material and crank rocker mechanism.

In this study, friction experiments were carried out on TC4 alloy friction discs and crank rocker mechanisms, both before and after exposure to atomic oxygen and proton irradiation. Nanoindentation, grazing incidence X-ray diffraction (GIXRD), and X-ray photoelectron spectroscopy were employed to systematically characterize alterations in mechanical properties, surface phase, and chemical composition.

The results show that the wear mechanism of TC4 alloy friction disc is mainly adhesive wear in vacuum environment, while the wear mechanism of crank rocker mechanism includes not only adhesive wear but also abrasive wear. Atomic oxygen exposure leads to the formation of more oxides on the surface of TC4 alloy, which form abrasive particles during the friction process. Proton irradiation will lead to a decrease in fatigue performance and an increase in hardness on the surface of TC4 alloy, thus causing fatigue wear on the surface of TC4 alloy, and more furrows appear on the crank rocker mechanism after proton irradiation. In the three environments, the characteristics of abrasive wear of the crank rocker mechanism are more obvious than those of the TC4 alloy friction disc.

These results highlight the importance of understanding the subtle effects of atomic oxygen and proton irradiation on the wear behavior of TC4 alloy and provide some insights for optimizing its performance in space applications.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-02-2024-0051/

This study aims to perform the surface treatment of synthetic α-Fe₂O₃ red iron oxide pigment with hydrolysate 3-aminopropyl silane (A) and colloidal silica (CS) and investigate the effects of surface-treated pigment on the styrene acrylic (SA) emulsion and polyurethane (PU) dispersion.

For this purpose, firstly red iron oxide particles were modified with A and CS separately in an aqueous medium. After isolation of the modified iron oxide were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS). Moreover, the degree of the dispersion stability of the modified pigment in coatings with SA emulsion and PU dispersion was investigated by using an oscillation rheometer. Loss (G''), storage (G') modulus, loss factor [tan(δ)] and yield stress (τ⁰) values were determined by performing amplitude and frequency sweep tests.

The τ⁰ in SA coatings decreases with the amount of used A and increases with the amount of used CS. The τ⁰ decreases as the amount of used A and CS in PU coatings increases. The use of CS on red iron oxide pigments causes storage modulus to increase in SA coatings at low angular frequencies, while it causes a decrease in PU coatings.

To the best of the authors’ knowledge, for the first time, the suspended state of the iron oxide hybrid pigment formed with CS in the coating was investigated rheologically in this study.

This study aims to investigate the corrosion inhibitor effect of migrating corrosion inhibitor (MCI) on Q235 steel in high alkaline environment under cathodic polarization.

This study investigated the electrochemical characteristics of Q235 steel with and without MCI by polarization curve and electrochemical impedance spectroscopy. Besides, the surface composition of Q235 steel under different environments was analyzed by X-ray photoelectron spectroscopy. In addition, the migration characteristic of MCI and the adsorption behavior of MCI under cathodic polarization were studied using Raman spectroscopy.

Diethanolamine (DEA) and N, N-dimethylethanolamine (DMEA) can inhibit the increase of Fe(II) in the oxide film of Q235 steel under cathodic polarization. The adsorption stability of DMEA film was higher under cathodic polarization potential, showing a higher corrosion inhibition ability. The corrosion inhibition mechanism of DEA and DMEA under cathodic polarization potential was proposed.

The MCI has a broad application prospect in the repair of damaged reinforced concrete due to its unique migratory characteristics. The interaction between MCIs, rebar and concrete with different compositions has been studied, but the passivation behavior of the steel interface in the presence of both the migrating electric field and corrosion inhibitors has been neglected. And it was investigated in this paper.

The purpose of this paper is to prepare a multifunctional nanocomposite that is slow-release and resistant to seawater corrosion and biofouling corrosion and to explore the synergistic effect between the two corrosion inhibitors.

The morphology, structure and release properties of CAP@HNTs, BTA@HNTs and CAP/BTA@HNTs were investigated by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, specific surface area analysis and UV spectrophotometry. The corrosion resistance and antimicrobial properties were investigated by electrochemical measurements and bioinhibition rate tests, and the synergistic effect between the two corrosion inhibitors was explored by X-ray photoelectron spectroscopy.

The CAP/BTA@HNTs are responsive to acidic environments and have significantly improved antibacterial and corrosion resistance compared with CAP@HNTs and BTA@HNTs. CAP and BTA have a positive synergistic effect on anticorrosion and antifouling.

Two types of inhibitors, anticorrosion and antifouling, were loaded into the same nanocontainer to prepare a slow-releasable and multifunctional nanocomposite with higher resistance to seawater corrosion and biocorrosion and to explore the synergistic effect of CAP and BTA on corrosion resistance.

The purpose of this study is to reveal the effect of nano-Al₂O₃ particle addition on the nucleation/growth kinetics, microhardness, wear resistance and corrosion resistance of Co–P–xAl₂O₃ nanocomposite plating.

The kinetics and properties of Co–P–xAl₂O₃ nanocomposite plating prepared by electroplating were investigated by electrochemical measurements, scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Vickers microhardness measurement, SRV5 friction and wear tester and atomic force microscopy.

A 12 g/L nano-Al₂O₃ addition in the plating solution can transform the nucleation/growth kinetics of the plating from the 3D progressive model to the 3D instantaneous model. The microhardness of the plating increased with the increase of nano-Al₂O₃ content in plating. The wear resistance of the plating did not adhere strictly to Archard’s law. An even and denser corrosion product film was generated due to the finer grains, with a high corrosion resistance.

The effect of different nano-Al₂O₃ addition on the nucleation/growth kinetics and properties of Co–P–xAl₂O₃ nanocomposite plating was investigated, and an anticorrosion mechanism of Co–P–xAl₂O₃ nanocomposite plating was proposed.

This study aims to investigate profoundly the protection of oil painting from deterioration using molybdenum trisulphide quantum dots (MoS3 QDs) against microbe, dirt accumulation and ultraviolet (UV) degradation.

The protection of painting against different deterioration factors necessitates the sustainable methods and advanced techniques. Scanning electron microscopy and transmission electron microscopy have been used to investigate the morphological structure of the painting and MoS3 QDs, respectively, and optical microscopy was used to examine antibacterial activity of MoS3 QDs towards different types of bacteria. To investigate the protection of painting against deterioration, the Fourier transform IR spectroscopy (FTIR) was used to investigate the paintings left in open air for a year. Chemical composition and crystal structure of MoS3 QDs have been studied using X-ray diffraction and X-ray photoelectron spectroscopy analysis, respectively.

The addition of MoS3 nanoparticles into painted coatings enhances the durability of linseed oil-based paintings toward UV ageing regarding the change in colour which confirmed by FTIR analysis. The protection of oil painting opposed to various deterioration factors was developed by involving of MoS3 QDs in the coating of the painting. Antibacterial effect of MoS3 QDs was tested against different types of bacteria such as Pseudomonas aeruginosa confirming that the MoS3 QDs involved in the coatings of oil paintings produces a high protection layer for the paintings against several microbial attacks. In addition, coatings containing MoS3 QDs reduce the accumulation of dirt on oil paintings when subjected to open air for a year.

The novel MoS3 QDs was used to form a protective and transparent coating layer for the oil painting to overcome the deterioration, displays the promising protection and can be applied for different oil paintings.

As a commonly engine coolant, ethylene glycol can produce corrosive acid byproducts at high temperatures when the car is running, specifically oxalic acid (OA), which can shorten the service life of engine. At the same time, chloride ions can also be introduced during coolant preparation processes. Therefore, this paper aims to investigate the synergistic corrosion behavior of Cl⁻ and OA on ADC12 aluminum alloy.

The electrochemical tests, scanning electron microscopy, energy dispersive spectrometer, X-ray diffraction and X-ray photoelectron spectroscopy) were used.

The results showed that the corrosion rate of the aluminum alloy increased with the increase of OA and Cl⁻ concentrations. After adding Cl⁻, the surface film of the aluminum alloy was further damaged, Cl⁻ has a synergistic effect with OA and their interaction further accelerated the corrosion of the aluminum alloy. Nevertheless, as the immersion time increased, the corrosion rate of the aluminum alloy gradually diminished due to the formation of aluminum oxalate.

The corrosion of ADC12 aluminum alloy was studied in OA, Cl⁻ and their mixed solutions; the synergistic effect of OA and Cl⁻ on the corrosion of ADC12 aluminum alloy was discussed, and aluminum oxalate formed inhibited its corrosion.

This paper aims to use an ionic liquid (IL, [HMIM]PF₆) to improve the lubrication performance of liquid metal (LM) as a lithium grease additive and to expand the application range of LM.

In this paper, the different mass ratios of [HMIM]PF₆/LM mixtures were added into the lithium grease on a four-ball tribo-meter to investigate the effects of its tribological behavior. Scanning electron mircoscope/energy dispersive spectroscopy and X-ray photoelectron spectroscopy were used to reveal the anti-wear and friction-reducing mechanism of the additives.

When the load was used at 461 N, the average coefficient of friction (ACOF) and average wear scar diameter (AWSD) of steel ball Lubricated with grease with an optimal ratio of 2:3 ([HMIM]PF₆/LM) were reduced by 32.8% and 30.5%, respectively. Friction and wear mechanisms are ascribed to friction-induced additive components that can simultaneously form a composite lubrication film consisting of FePO₄, FeF₃, Ga₂O₃, In₂O₃ and SnO₂.

Compared with the pure lithium-based grease, when [HMIM]PF₆/LM was added with an optimal ratio of 2:3, the ACOF and AWSD were reduced by 12.4% from 0.097 to 0.085 and 23.8% from 552.117 µm to 420.590 µm under 392 N, respectively. When at 461 N, the ACOF and AWSD of steel ball were reduced by 32.8% from 0.122 to 0.082 and 30.5% from 715.714 µm to 497.472 µm, respectively. It was shown that the simultaneous addition of LM and [HMIM]PF₆ can form a composite lubrication film consisting of FePO₄, FeF₃, Ga₂O₃, In₂O₃ and SnO₂.

In this paper, [HMIM]P F₆ is added with LM simultaneously to improve the lubrication properties of lithium grease, and expand the application scope of LM.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0017/

This paper aims to evaluate the effects of banana (Musa) peel and guava (Psidium guajava) leaves extract as mordants on jute–cotton union fabrics dyed with onion skin extract as a natural dye.

The dye was extracted from the outer skin of onions by boiling in water and later concentrated. The bio-mordants were prepared by maceration using methanol and ethanol. The fabrics were pre-mordanted, simultaneously mordanted and post-mordanted with various concentrations according to the weight of the fabric. The dyed and mordanted fabrics were later subjected to measurement of color coordinates, color strength and colorfastness to the washing test. Furthermore, the dyed samples were characterized by Fourier transform infrared, and different chemical bonds were analyzed by X-ray photoelectron spectroscopy analysis.

Significant improvement was obtained in colorfastness and color strength values in various instances using banana peel and guava leaves as bio mordants. Post-mordanted with banana peel provided the best results for wash fastness. Better color strength was achieved by fabric post-mordanted with guava leave extracts.

Sustainable dyeing methods of natural dyes using banana peel and guava leaves as bio mordants were explored on jute–cotton union fabrics. Improvement in colorfastness and color strength for various instances was observed. Thus, this paper provides a promising alternative to metallic salt mordants.