Search results

The purpose of this study is to know the influence of palm oil fuel ash and metakaolin on the strength of concrete and crack resistance of reinforced concrete beam. An ordinary portland cement has been used in the concretes production where it is an important material to be considered due to its nature that reacts with every substance present. During the cement production, a significant amount of carbon dioxide is emitted from the clinker in rotary kiln and lot of energy is required in the production processes. Such an event can be prevented by replacing the part of cement with metakaolin (MK) and palm oil fuel ash (POFA). Aside from being a cementitious alternative, the materials can also contribute to a greener environment and more sustainable building, as POFA is available in Malaysia and may be used to substitute cement and minimize pollution.

This study assesses the effect of MK and POFA on the concrete in terms of compressive strength and cracks pattern of the reinforced concrete beam based on the relevant previous studies.

From this study, the compressive strength of concrete containing MK and POFA was higher than the control mix with the percentage of improvement in the range of 0.8%–78.2% for MK and 0.5%–14%, respectively. The optimum content of MK and POFA is between the range of 10% and 15% and 10% and 20%, respectively, to achieve high strength of concrete. Other than that, the inclusion of MK to the concrete mix improves the strength of reinforced concrete beams and reduces cracks on the surface of reinforced concrete beams, whereas the inclusion of POFA to the concrete mix increases the cracks on reinforced concrete beams. The cracks appeared within the flexure zone of every beam containing the MK and POFA.

It was found that the fineness of MK and POFA has a significant influence on the mechanical properties of concrete.

This paper presents the second part of the investigation on resistance to elevated temperatures of a proposed hybrid composite concrete (NCSF-Crete) mix. The composite including nano metakaolin (NC) and steel fibers (SF) in addition to regular concrete components has proven -in the first published part-earlier promoted fresh concrete behavior, and to have reduced loss in compressive strength after exposure to a wide range of elevated temperatures. This presented work evaluates another two critical mechanical characteristics for the proposed composite -namely- splitting and bond strengths.

A modified formula correlating splitting and compressive strength (28 days) based on experiments results for NCSF is proposed and compared to formulas derived for regular concrete in different design codes. Finally, both spitting and bond strengths are evaluated pre- and post-exposure to elevated temperatures reaching 600 °C for two hours.

The proposed NCSF-Crete shows remarkable fire endurance, especially in promoting bond strength as after 600 °C heat exposure tests, it maintained strength equivalent to 70% of a regular concrete control mix at room temperature. Improving residual splitting strength was very significant up to 450 °C exposure.

Obvious deterioration is monitored in splitting resistance for all concretes at 600 °C.

This proposed composite improved elevated heats resistance of the most significant concrete mechanical properties.

Using a more green and sustainable constituents in the composite.

The proposed composite gathers the merits of using NC and SF, each has been investigated separately as an addition to concrete mixes.

Nano-Clay (NC) is reported as a candidate partial replacement for cement, due to its abundance and relatively low cost - beside reported promotion of different concrete properties. On the other hand, Steel Fibres (SF) has proven to have a positive effect on post fire exposure residual strength of concrete. This paper aims to present the outcomes of a comprehensive research program assessing a hybrid mix between NC and SF in concrete mixtures (NCSF-CRETE).

Physical chemical and physical characterization of NC is performed using different tools as XRF spectrometer, and TEM micrograph. Fresh concrete properties of NSCF-CRETE as slump and air content are investigated. Enhancement in permeability using NSCF is verified by comparing its resistance to the penetration of chlorides resistance with regular concrete mix. Besides, the proposed NCSF-CRETE compressive strength is evaluated compared to mixes with NC and SF each used separately at different curing ages. Besides, NSCF and compared mixes are exposed to an indirect fire testing program – two hours exposure – for: 300, 450 and 600°C. Degradation in compressive strength was investigated after exposure to different temperatures and percentage of residual strength is reported.

Results indicated an improved performance of NCSF -CRETE of about 40% compared to regular concrete in compressive strength at normal conditions. This improvement extended to its behavior when subjected to indirect fire exposure NSCF also maintained 40% more strength than the residual in regular concrete mix – which suffered severe damage – after 2 h exposure to 600°C.

Using NCSF-Crete allows retrofitting the structure after exposure to such drastic conditions.

In recent years, fire accidents in engineering structures have often been reported worldwide, leading to a severe risk to life and property safety. The present study is carried out to evaluate the performance of Ground Granulated Blast Furnace Slag (GGBS) and fly ash–blended laterized mortars at elevated temperatures.

This test program includes the replacement of natural river sand with lateritic fine aggregates (lateritic FA) in terms of 0, 50 and 100%. Also, the ordinary Portland cement (OPC) was replaced with fly ash and GGBS in terms of 10, 20, 30% and 20, 40 and 60%, respectively, for producing blended mortars.

This paper presents results related to the determination of residual compressive strengths of lateritic fine aggregates-based cement mortars with part replacement of cement by fly ash and GGBS exposed to elevated temperatures. The effect of elevated temperatures on the physical and mechanical properties was evaluated with the help of microstructure studies and the quantification of hydration products.

A sustainable cement mortar was produced by replacing natural river sand with lateritic fine aggregates. The thermal strength deterioration features were assessed by exposing the control specimens and lateritic fine aggregates-based cement mortars to elevated temperatures. Changes in the mechanical properties were evaluated through a quantitative microstructure study using scanning electron microscopy (SEM) images. The phase change of hydration products after exposure to elevated temperatures was qualitatively analyzed by greyscale thresholding of SEM images using Image J software.

Concrete-filled double skin steel tubes (CFDST) columns are taken more attention due to their ability to withstand high structural loads in structures such as high-rise buildings, bridges' piers, offshore and marine structures. This paper is intended to improve the CFDST column's capacity without the need to increase the column's size to maintain its lightweight by filling it with self-compacted concrete (SCC) containing nanoclay (NC).

First, experimental investigation is conducted to select the optimal NC percentage that improves the mechanical properties. Different mixing method, mixture ingredients, cement content, and NC percentage are considered. Then, slender and short CFDST columns are tested for axial capacity to investigate the effect of adding the optimum NC percentage on column's capacity and failure mode.

The test results show that adding 3% NC by cement weight using dry mixing method to SCC is the optimum ratio. It is concluded that adding 3% NC by cement weight increased the CFDST column's capacity, especially the specimens with higher slenderness ratio. Moreover, it is concluded that more specimens should be tested under various geometric and reinforcement details.

Recently, CFDST tube columns solve many structural and architectural problems that engineers have encountered in traditional systems. Therefore, more studies are required to design high-performance columns capable of carrying complex loads with high efficiency since the traditional design could not achieve the required performance. Since concrete contributes to a large portion in the axial capacity of the CFDST columns, it is proposed to improve the CFDST column's capacity without the need to increase the column's size to maintain its lightweight by filling it with (SCC containing NC. Previous research has affirmed the effectiveness of employing nanoclay in the concrete's workability, durability, microstructures, and mechanical properties.

The purpose of this paper is to study the effect of nano alumina (Al₂O₃) on the properties of fresh concrete, hardened concrete and microstructure of concrete incorporated with high range water reducer (HRWR). This initiative was taken to improve characteristic properties of concrete using nano alumina because nano alumina can be easily be manufactured from a scrap of industrial aluminum products, so its incorporation in concrete will not only reduce industrial aluminum waste but will also change the morphology of concrete at the microstructural level.

To accomplish the objectives of the research, four different concrete mixes with the constant water–cement ratio (W/C) and superplasticizer (SP) content 0.4 and 0.6% by weight of cement, respectively, were prepared, whereas nano alumina content was altered by 0.3% and 0.4% by weight of cement. Fresh property of concrete was analyzed by using slump cone test, whereas hardened properties of concrete were analyzed through compression test and flexural strength test. The interaction of nano alumina with concrete composite was evaluated using an X-ray diffraction test.

It was observed that 0.6% superplasticizer by weight of cement increased workability by 22% but with the addition of 0.3%, nano alumina by weight of cement workability decreased by 31%. Compressive strength increased by 4.88% with the addition of 0.6% superplasticizer but with the addition of 0.3% nano alumina by weight of cement compressive strength increased by 18.60%. Also, flexural strength increased by 1.21% with the addition of 0.6% superplasticizer by weight of cement but with the addition of 0.3% nano alumina by weight of cement flexural strength increased by 8.76%. With the addition of superplasticizer, alite and belite phases remained un-hydrated but with the addition of nano alumina alite phase was hydrated while belite phase was un-hydrated. The size of belite crystals in mixes having nano alumina was less than that of mix having 0.6% superplasticizer. Also with the addition of nano alumina, a calcium aluminum silicate phase was formed which was responsible for the increment of strength in mixes having nano alumina.

Incorporation nano alumina (Al₂O₃) in concrete will not only reduce industrial aluminum waste but will also reduce CO₂ emission. Nano alumina (Al₂O₃) also changes morphology of concrete at micro structural level.

Traditional simulation research of geological and similar engineering models, such as landslides or other natural disaster scenarios, usually focuses on the change of stress and the state of the model before and after destruction. However, the transition of the inner change is usually invisible. To optimize and make models more intelligent, this paper aims to propose a perceptible design to detect the internal temperature change transformed by other energy versions like stress or torsion.

In this paper, micron diamond particles were embedded in 3D printed geopolymers as a potential thermal sensor material to detect the inner heat change. The authors use synthetic micron diamond powder to reinforced the anti-corrosion properties and thermal conductivity of geopolymer and apply this novel geopolymer slurry in the direct ink writing (DIW) technique.

As a result, the addition of micron diamond powder can greatly influence the rheology of geopolymer slurry and make the geopolymer slurry extrudable and suitable for DIW by reducing the slope of the viscosity of this inorganic colloid. The heat transfer coefficient of the micron diamond (15 Wt.%)/geopolymer was 50% higher than the pure geopolymer, which could be detected by the infrared thermal imager. Besides, the addition of diamond particles also increased the porous rates of geopolymer.

In conclusion, DIW slurry deposition of micron diamond-embedded geopolymer (MDG) composites could be used to manufacture the multi-functional geological model for thermal imaging and defect detection, which need the characteristic of lightweight, isolation, heat transfer and wave absorption.

The aim of the work is to investigate structural behaviour of reinforced concrete (RF) beam retrofitted with basalt fibre (BF) fabric. The incorporation of BF showed enhancement in bending strength, to increase confinement and to repair damages caused by cracking. In the early decades, using BF for composite materials shaped BF as an excellent physical substance with necessary mechanical properties, highlighting the significant procedures ability.

Specimens were casted with U-wrapped BF and then evaluated based on flexural tests. In the test carried over for flexural fortifying assessment, BF reinforcements demonstrated a definitive quality improvement in the case of the subjected control sample; ultimately, the end impacts depend upon the applied test parameters. From the outcomes introduced in this comparison, for the double-wrapped sample, the modifications improved by 12% than that of the single-wrapped beam, which is identified to subsist for a better strengthening of new-age retrofitting designs.

The current research deals with the retrofitting of RC beam by conducting a comparative experiment on wrapping of BF (single or double BF wrapping) in improving the mechanical behavior of concrete.

It can be shown from the experimental results that increasing the number of layers has significant effect on basalt strengthened beams.

Nowadays, thermal comfort plays a prominent role in contemporary construction practices. Appropriate thermal insulation not only offers energy efficiency benefits in buildings but also enhances occupant well-being, comfort, and productivity. Therefore, a comprehensive understanding of the thermal properties of building materials is essential. This research aims to prepare and investigate a lightweight gypsum-based composite incorporating nano montmorillonite with advanced thermal insulation properties, considering both quality and cost-effectiveness while ensuring environmental compatibility.

This study adopts a laboratory experimental approach. A gypsum sample (without additives) and seven samples of gypsum combined with varying percentages of sodium and calcium montmorillonite nanoclays undergo extensive testing and analysis. Subsequently, the properties of these samples are compared.

The results indicate that adding montmorillonite nanoclays to gypsum composites reduces the density of the tested samples and increases their porosity. Moreover, the thermal conductivity coefficient decreases in these samples, significantly improving the thermal insulation properties of the lightweight gypsum plaster. This improvement is more pronounced in samples containing sodium montmorillonite nanoclay compared to calcium-based samples. Additionally, the investigations reveal that compressive strength decreases with the addition of montmorillonite to the samples.

In this research, laboratory experiments were conducted to investigate the physical and mechanical properties of gypsum plaster with varying percentages of sodium and calcium montmorillonite nanoclays. The studied properties include density, porosity, thermal conductivity coefficient, and compressive strength. Additionally, stress-strain diagrams, elastic modulus, and initial and secondary critical stresses were analyzed for each specimen.

The use of huge quantity of natural fine aggregate (NFA) and cement in civil construction work which have given rise to various ecological problems. The industrial waste like blast furnace slag (GGBFS), fly ash, metakaolin and silica fume can be partly used as a replacement for cement and manufactured sand obtained from crusher and partly used as fine aggregate. The purpose of this paper is to predict the shear strength of concrete using artificial neural network (ANN) for concrete made by using different pozzolans and partly replacing NFA by manufactured sand (MS) which can reduce the time and experimental cost.

In this work, MATLAB software model is developed using neural network toolbox to predict the shear strength of concrete made by using pozzolanic materials and partly replacing NFA by manufactured sand (MS). Shear strength was experimentally calculated, and results obtained from experiment were used to develop the ANN model. A total of 131 results values were used to modeling formation, and from that 30% data record was used for testing purpose and 70% data record was used for training purpose. In total, 25 input materials properties were used to find the 28 days shear strength of concrete obtained from partly replacing cement with pozzolans and partly replacing NFA by manufactured sand (MS).

The results obtained from ANN model provide very strong accuracy to predict shear strength of concrete obtained from partly replacing cement with pozzolans and NFA by manufactured sand.

This research study is on determining shear strength of concrete using ANN. The use of this study is to predict the shear strength of concrete using ANN for concrete made by using different pozzolans and partly replacing NFA by manufactured sand (MS) which can reduce the time and experimental cost.