Search results

The Monte‐Carlo particle model is a technique of simulating small semiconductor devices. It consists briefly of following the detailed transport histories of individual carriers, their time of free flight and consequent scattering chosen by a random number technique. A description of the method is given. The method has proved itself successful in semiconductor analysis, and as an example of its application we are using it to study the influence the epitaxial doping has on the performance of field‐effect transistors. We are comparing a transistor with an epitaxially grown active layer, with one with an ion implanted active layer and with an ideal device with an abrupt transition between the epilayer and the substrate. The cut‐off bias for ideal transistor is found to be more sharply defined than for the other two types of transistors. The spatial distribution of the carriers follows roughly the doping profile near the source. Underneath the gate the peak of the carrier density is pushed further down and into the substrate as the gate bias increases. This peak also weakens as the gate bias rises, and vanishes at, and beyond cut‐off. In the high field region after the gate the upper valleys population increases with increased drain bias and decreases with increased gate bias. The power gain and the y‐parameters are examined for all devices, both near pinch‐off and for no external gate bias. In both cases the ion implanted transistor shows the greatest gain. This transistor also exhibits the lowest minimum noise figure.

The purpose of this paper is to analyse the operation of p-type side gate junctionless silicon transistor (SGJLT) in accumulation region through experimental measurements and 3-D TCAD simulation results. The variation of electric field components, carrier’s concentration and valence band edge energy towards the accumulation region is explored with the aim of finding the origin of SGJLT performance in the accumulation operational condition.

The device is fabricated by atomic force microscopy nanolithography on silicon-on-insulator wafer. The output and transfer characteristics of the device are obtained using 3-D Technology Computer Aided Design (TCAD) Sentaurus software and compared with experimental measurement results. The advantages of AFM nanolithography in contact mode and Silicon on Insulator (SOI) technology were implemented to fabricate a simple structure which exhibits the behaviour of field effect transistors. The device has 200-nm channel length, 100-nm gate gap and 4 μm for the distance between the source and drain contacts. The characteristics of the fabricated device were measured using an Agilent HP4156C semiconductor parameter analyzer (SPA). A 3-D TCAD Sentaurus tool is used as the simulation platform. The Boltzmann statistics is adopted because of the low doping concentration of the channel. Hydrodynamic model is taken to be as the main transport model for all simulations, and the quantum mechanical effects are ignored. A doping dependent Masetti mobility model was also included as well as an electric field dependent model with Shockley–Read–Hall (SRH) carrier recombination/generation.

We have obtained that the device is a normally on state device mainly because of the lack of work functional difference between the gate and the channel. Analysis of electric field components’ variation, carrier’s concentration and valence band edge energy reveals that increasing the negative gate voltage drives the device into accumulation region; however, it is unable to increase the drain current significantly. The positive slope of the hole quasi-Fermi level in the accumulation region presents mechanism of carriers’ movement from source to drain. The influence of electric field because of drain and gate voltage on charge distribution explains a low increasing of the drain current when the device operates in accumulation regime.

The proposed side gate junctionless transistors simplify the fabrication process, because of the lack of gate oxide and physical junctions, and implement the atomic force microscopy nanolithography for fabrication process. The optimized structure with lower gap between gate and channel and narrower channel would present the output characteristics near the ideal transistors for next generation of scaled-down devices in both accumulation and depletion region. The presented findings are verified through experimental measurements and simulation results.

An simple model for the simulation of the electrical behaviour of several types of junction controlled field‐effect transistors is proposed. It is based on the calculation of the carrier concentration in the channel by means of a self‐consistent solution of Schrödinger and Poisson's equation in the direction perpendicular to the current flow. Based on the carrier concentration the dc, the small‐signal, and also the noise properties of the devices may be simulated. The calculated characteristics of a sub‐quarter micron gate GaAs MESFET, a δ‐doped GaAs FET and a Velocity Modulation Transistor will be presented and discussed.

The purpose of this paper is to propose a leakage reduction technique which will works for complementary metal oxide semiconductor (CMOS) and fin field effect transistor (FinFET). Power consumption will always remain one of the major concerns for the integrated circuit (IC) designers. Presently, leakage power dominates the total power consumption, which is a severe issue. It is undoubtedly clear that the scaling of CMOS revolutionizes the IC industry. Still, on the contrary, scaling of the size of the transistor has raised leakage power as one of the significant threats to the IC industry. Scaling of the devices leads to the scaling of other device parameters, which includes threshold voltage also. The scaling of threshold voltage leads to an exponential increase in the sub-threshold current. So, many leakage reduction techniques have been proposed by researchers for CMOS from time to time. Even the other nano-scaled devices such as FinFET, carbon nanotube field effect transistor and tunneling field effect transistor, have been introduced, and FinFET is the one which has evolved as the most favorable candidate for replacing CMOS technology.

Because of its minimum leakage and without having limitation of the short channel effects, it gradually started replacing the CMOS. In this paper, the authors have proposed a technique for leakage reduction for circuits using nano-scaled devices such as CMOS and FinFET. They have compared the proposed PMOS FOOTER SLEEP with the existing leakage reduction techniques such as LECTOR technique, LECTOR FOOTER SLEEP technique. The proposed technique has been implemented using CMOS and FinFET devices. This study found that the proposed method reduces the average power, as well as leakage power reduction, for both CMOS and FinFET devices.

This study found that the proposed method reduces the average power as well as leakage power reduction for both CMOS and FinFET devices. The delay has been calculated for the proposed technique and the existing techniques, which verifies that the proposed technique is suitable for high-speed circuit applications. The authors have implemented higher order gates to verify the performance of the proposed circuit. The proposed method is suitable for deep-submicron CMOS technology and FinFET technology.

All the existing techniques were proposed for either CMOS device or FinFET device, but the authors have implemented all the techniques with both the devices and verified with the proposed technique for CMOS as well as FinFET devices.

The purpose of this paper is to propose a time‐dependent mobility degradation model which is independent from the process or operating conditions.

In total, four transistors under test are electrically stressed using constant positive electrical stress voltage technique with the gate bias of V_G=40 V DC, where the source and drain were grounded. The authors increased the stress voltage step by step to avoid electrostatic discharge and recorded the I_D‐V_DS and I_D‐V_GS measurements in time intervals during the stress.

The experimental results show that the output current and the threshold voltage of the transistor are increased after the stress. Mobility and channel length are decreased. The changes in the transistor parameters were associated to interface state Si/SiO₂ effects. The authors used the physical changes in transistor and proposed a new‐time dependent mobility degradation model. The mobility change was calculated using the proposed model and compared with the experimental results. It was seen that the calculated and experimental results are in good agreement.

This is an original research paper and enables the mobility degradation to be predicted independently from effects of process or operational changes such as oxide thickness, substrate doping, and applied voltages on transistor.

The purpose of this paper is to present the influence of gate dielectric etching on obtained MISFET (metal insulator semiconductor field effect transistor) structures. Because of its properties, aluminum nitride (AlN) layers can be successfully used in a large area of applications. In addition, AIN has a wide bandgap (6.2eV) and high thermal conductivity (3.2 W/cm * K). Its melting temperature is greater than 2,000°C. The relative permittivity is about 9. All these features (especially high power, high temperature and high-frequency) make AlN a useful material in the fields of electronic, optical and acoustic applications.

To fabricate n-channel transistors, silicon technology was used. The 50-nm thick AlN films were deposited using the magnetron sputtering. After preparation of SiO₂/AlN stack as the gate dielectric, the optimization processes of dry etching in plasma environment by Taguchi method were realized. In the next step, three methods of AlN etching were selected and used to MISFET device fabrication. Atomic force microscopy and scanning electron microscopy allowed to surfacing of the state observation after etching process. The current–voltage (I–V) output and transfer characteristics of structures with modified etch technology were measured. Keithley SMU 236/237/238 measurement set was used.

In this research work, a method of AlN etching in a field effect transistor technology was developed and improved. Current−voltage characteristics of obtained MISFET structures were measured and compared. Influence of etching procedure on transistors properties was examined.

The obtained results allow improving the MISFET technology based on AlN film as a gate dielectric. The complete research work will allow using the developed technologies to implement in highly sensitive ion-sensitive field effect transistor (ISFET) structures in the future. The improvement of the etching element in the technology strongly influences the detection capabilities and operating range of the transistor.

This paper aims to propose a new fin field-effect transistor (FinFET)-based domino technique low-power series connected foot-driven transistors logic in 32 nm technology and examine its performance parameters by performing transient analysis.

In the proposed technique, the leakage current is reduced at footer node by a division of current to improve the performance of the circuit in terms of average power consumption, propagation delay and noise margin. Simulation of existing and proposed techniques are carried out in FinFET and complementary metal-oxide semiconductor technology at FinFET 32 nm technology for 2-, 4-, 8- and 16-input domino OR gates on a supply voltage of 0.9 V using HSPICE.

The proposed technique shows maximum power reduction of 77.74% in FinFET short gate (SG) mode in comparison with current-mirror-based process variation tolerant (CPVT) technique and maximum delay reduction of 51.34% in low power (LP) mode in comparison with CPVT technique at a frequency of 100 MHz. The unity noise gain of the proposed circuit is 1.10× to 1.54× higher in comparison with different existing techniques in FinFET SG mode and 1.11× to 1.71× higher in FinFET LP mode. The figure of merit of the proposed circuit is up to 15.77× higher in comparison with existing domino techniques.

The research proposes a new FinFET-based domino technique and shows improvement in power, delay, area and noise performance. The proposed design can be used for implementing high-speed digital circuits such as microprocessors and memories.

The purpose of this paper is to develop and apply accurate and original models to understand and analyze the effects of the fabrication temperatures on thermal-induced stress and speed performance of nano positively doped metal oxide semiconductor (pMOS) transistors.

The speed performances of nano pMOS transistors depend strongly on the mobility of holes, which itself depends on the thermal-induced extrinsic stress σ. The author uses a finite volume method to solve the proposed system of partial differential equations needed to calculate the thermal-induced stress σ accurately.

The thermal extrinsic stress σ depends strongly on the thermal intrinsic stress σ₀, thermal intrinsic strain ε₀, elastic constants C11 and C12 and the fabrication temperatures. In literature, the effects of fabrication temperatures on C11 and C12 needed to calculate thermal-induced stress σ₀ have been ignored. The new finding is that if the effects of fabrication temperatures on C11 and C12 are ignored, then, the values of stress σ₀ and σ will be overestimated and, then, not accurate. Another important finding is that the speed performance of nano pMOS transistors will increase if the fabrication temperature of silicon-germanium films used as stressors is increased.

To predict correctly the thermal-induced stress and speed performance of nano pMOS transistors, the effects of fabrication temperatures on the elastic constants required to calculate the thermal-induced intrinsic stress σ₀ should be taken into account.

There are three levels of originalities. The author considers the effects of the fabrication temperatures on extrinsic stress σ, intrinsic stress σ₀ and elastic constants C11 and C12.

This paper is an unprecedented effort to resolve the performance issue of very large scale integrated circuits (VLSI) interconnects encountered because of the scaling of device dimensions. Repeater interpolation technique is an effective approach for enhancing speed of interconnect network. Proposed buffers as repeater are modeled by using dual chirality multi-V_t technology to reduce delay besides mitigating average power consumption. Interconnects modeled with carbon nanotube (CNT) technology are compared with copper interconnect for various lengths. Buffer circuits are designed with both CNT and metal oxide semiconductor technology for comparison by using various combination of (CMOSFET repeater-Cu interconnect) and (CNTFET repeater-CNT interconnect). Compared to conventional buffer, ProposedBuffer1 saves dynamic power by 84.86%, leakage power by 88% and offers reduction in delay by 72%. ProposedBuffer2 brings about dynamic power saving of 99.94%, leakage power saving of 93%, but causes delay penalty. Simulation using Stanford SPICE model for CNT and silicon-field effective transistor berkeley short-channel IGFET Model4 (BSIM4) predictive technology model (PTM) for MOS is done in H simulation program with integrated circuit emphasis for 32 nm.

Usually, the dynamic power consumption dominates the total power, while the leakage power has a negligible effect. But with the scaling of device technology, leakage power has become one of the important factors of consideration in low power design techniques. Various strategies are explored to suppress the leakage power in standby mode. The adoption of a multi-threshold design strategy is an effective approach to improve the performance of buffer circuits without compromising on the delay and area overhead. Unlike MOS technology, to implement multi-V_t transistors in case of CNT technology is quite easy. It can be achieved by varying diameter of carbon nanotubes using chirality control.

An unprecedented approach is taken for optimizing the delay and power dissipation and hence drastically reducing energy consumption by keeping proper harmony between wire technology and repeater-buffer technology. This paper proposes two novel ultra-low power buffers (PB1 and PB2) as repeaters for high-speed interconnect applications in portable devices. PB1 buffer implemented with high-speed CML technique nested with multi-threshold (V_t) technology sleep transistor so as to improve the speed along with a reduction in standby power consumption. PB2 is judicially implemented by inserting separable sized, dual chirality P type carbon nanotube field effective transistors. The HSpice simulation results justify the correctness of schemes.

Result analysis points out that compared to conventional Cu interconnect, the CNT interconnects paired with Proposed CNTFET buffer designs are more energy efficient. PB1 saves dynamic power by 84.86%, reduces propagation delay by 72% and leakage power consumption by 88%. PB2 brings about dynamic power saving of 99.4%, leakage power saving of 93%, with improvement in speed by 52%. This is mainly because of the fact that CNT interconnect offers low resistance and CNTFET drivers have high mobility and ballistic mode of operation.

The present paper aims to propose a basic current mirror-sensing circuit as an alternative to the traditional Wheatstone bridge circuit for the design and development of high-sensitivity complementary metal oxide semiconductor (CMOS)–microelectromechanical systems (MEMS)-integrated pressure sensors.

This paper investigates a novel current mirror-sensing-based CMOS–MEMS-integrated pressure-sensing structure based on the piezoresistive effect in metal oxide field effect transistor (MOSFET). A resistive loaded n-channel MOSFET-based current mirror pressure-sensing circuitry has been designed using 5-μm CMOS technology. The pressure-sensing structure consists of three identical 10-μm-long and 50-μm-wide n-channel MOSFETs connected in current mirror configuration, with its input transistor as a reference MOSFET and output transistors are the pressure-sensing MOSFETs embedded at the centre and near the fixed edge of a silicon diaphragm measuring 100 × 100 × 2.5 μm. This arrangement of MOSFETs enables the sensor to sense tensile and compressive stresses, developed in the diaphragm under externally applied pressure, with respect to the input reference transistor of the mirror circuit. An analytical model describing the complete behaviour of the integrated pressure sensor has been described. The simulation results of the pressure sensor show high pressure sensitivity and a good agreement with the theoretical model has been observed. A five mask level process flow for the fabrication of the current mirror-sensing-based pressure sensor has also been described. An n-channel MOSFET with aluminium gate was fabricated to verify the fabrication process and obtain its electrical characteristics using process and device simulation software. In addition, an aluminium gate metal-oxide semiconductor (MOS) capacitor was fabricated on a two-inch p-type silicon wafer and its CV characteristic curve was also measured experimentally. Finally, the paper presents a comparative study between the current mirror pressure-sensing circuit with the traditional Wheatstone bridge.

The simulated sensitivities of the pressure-sensing MOSFETs of the current mirror-integrated pressure sensor have been found to be approximately 375 and 410 mV/MPa with respect to the reference transistor, and approximately 785 mV/MPa with respect to each other. The highest pressure sensitivities of a quarter, half and full Wheatstone bridge circuits were found to be approximately 183, 366 and 738 mV/MPa, respectively. These results clearly show that the current mirror pressure-sensing circuit is comparable and better than the traditional Wheatstone bridge circuits.

The concept of using a basic current mirror circuit for sensing tensile and compressive stresses developed in micro-mechanical structures is new, fully compatible to standard CMOS processes and has a promising application in the development of miniaturized integrated micro-sensors and sensor arrays for automobile, medical and industrial applications.