Search results

The present paper aims to propose a basic current mirror-sensing circuit as an alternative to the traditional Wheatstone bridge circuit for the design and development of high-sensitivity complementary metal oxide semiconductor (CMOS)–microelectromechanical systems (MEMS)-integrated pressure sensors.

This paper investigates a novel current mirror-sensing-based CMOS–MEMS-integrated pressure-sensing structure based on the piezoresistive effect in metal oxide field effect transistor (MOSFET). A resistive loaded n-channel MOSFET-based current mirror pressure-sensing circuitry has been designed using 5-μm CMOS technology. The pressure-sensing structure consists of three identical 10-μm-long and 50-μm-wide n-channel MOSFETs connected in current mirror configuration, with its input transistor as a reference MOSFET and output transistors are the pressure-sensing MOSFETs embedded at the centre and near the fixed edge of a silicon diaphragm measuring 100 × 100 × 2.5 μm. This arrangement of MOSFETs enables the sensor to sense tensile and compressive stresses, developed in the diaphragm under externally applied pressure, with respect to the input reference transistor of the mirror circuit. An analytical model describing the complete behaviour of the integrated pressure sensor has been described. The simulation results of the pressure sensor show high pressure sensitivity and a good agreement with the theoretical model has been observed. A five mask level process flow for the fabrication of the current mirror-sensing-based pressure sensor has also been described. An n-channel MOSFET with aluminium gate was fabricated to verify the fabrication process and obtain its electrical characteristics using process and device simulation software. In addition, an aluminium gate metal-oxide semiconductor (MOS) capacitor was fabricated on a two-inch p-type silicon wafer and its CV characteristic curve was also measured experimentally. Finally, the paper presents a comparative study between the current mirror pressure-sensing circuit with the traditional Wheatstone bridge.

The simulated sensitivities of the pressure-sensing MOSFETs of the current mirror-integrated pressure sensor have been found to be approximately 375 and 410 mV/MPa with respect to the reference transistor, and approximately 785 mV/MPa with respect to each other. The highest pressure sensitivities of a quarter, half and full Wheatstone bridge circuits were found to be approximately 183, 366 and 738 mV/MPa, respectively. These results clearly show that the current mirror pressure-sensing circuit is comparable and better than the traditional Wheatstone bridge circuits.

The concept of using a basic current mirror circuit for sensing tensile and compressive stresses developed in micro-mechanical structures is new, fully compatible to standard CMOS processes and has a promising application in the development of miniaturized integrated micro-sensors and sensor arrays for automobile, medical and industrial applications.

Tunnel field effect transistors (TFETs) have significantly steeper sub-threshold slope (24–30 mv/decade), as compared with the conventional metal–oxide–semiconductor field-effect transistors (MOSFETs), which have a sub-threshold slope of 60 mv/decade at room temperature. The steep sub-threshold slope of TFETs enables a much faster switching, making TFETs a better option than MOSFETs for low-voltage VLSI applications. The purpose of this paper is to present a novel hetero-junction TFET-based Schmitt triggers, which outperform the conventional complementary metal oxide semiconductor (CMOS) Schmitt triggers at low power supply voltage levels.

The conventional Schmitt trigger has been implemented with both MOSFETs and HTFETs for operation at a low-voltage level of 0.4 V and a target hysteresis width of 100 mV. Simulation results have indicated that the HTFET-based Schmitt trigger not only has significantly lower delays but also consumes lesser power as compared to the CMOS-based Schmitt trigger. The limitations of the conventional Schmitt trigger design have been analysed, and improved CMOS and CMOS–HTFET hybrid Schmitt trigger designs have been presented.

The conventional Schmitt trigger implemented with HTFETs has 99.9% lower propagation delay (29ps) and 41.2% lesser power requirement (4.7 nW) than the analogous CMOS Schmitt trigger, which has a delay of 36 ns and consumes 8 nW of power. An improved Schmitt trigger design has been proposed which has a transistor count of only six as compared to the eight transistors required in the conventional design. The proposed improved Schmitt trigger design, when implemented with only CMOS devices enable a reduction of power delay product (PDP) by 98.4% with respect to the CMOS conventional Schmitt trigger design. The proposed CMOS–HTFET hybrid Schmitt trigger further helps in decreasing the delay of the improved CMOS-only Schmitt trigger by 70% and PDP by 21%.

The unique advantage of very steep sub-threshold slope of HTFETs has been used to improve the performance of the conventional Schmitt trigger circuit. Novel CMOS-only and CMOS–HTFET hybrid improved Schmitt trigger designs have been proposed which requires lesser number of transistors (saving 70% chip area) for implementation and has significantly lower delays and power requirement than the conventional designs.

The performance of the conventional 6T SRAM cell can be improved by using GNRFET devices with multi-threshold technology. The proposed cell shows the strong capability to operate at the minimum supply voltage of 325 mV, whereas the conventional Si-CMOS 6 T SRAM unable to operate below 725 mV, which result in an acceptable failure rate.The advance of Si-CMOS (complementary metal-oxide-semiconductor) based 6 T SRAM cell faces inherent limitation with aggressive downscaling. Hence, there is a need to propose alternatives for the conventional cells.

This study aims to improve the performance of the conventional 6T SRAM cell using dual threshold technology, device sizing, optimization of supply voltage under process variation with GNRFET technology. Further performance can be enhanced by resolving half-select issue.

The GNRFET-based 6T SRAM cell demonstrates that it is capable of continued improve the performance under the process, voltage, and temperature (PVT) variations significantly better than its CMOS counterpart.

Nano-material fabrication technology of GNRFETs is in the early stage; hence, the different transistor models can be used to evaluate the parameters of future GNRFETs circuit.

GNRFET devices are suitable for implementing low power and high density SRAM cell.

The conventional Si-CMOS 6 T SRAM cell is a core component and used as the mass storage element in cache memory in computer system organization, mobile phone and other data storage devices.

This paper presents a new approach to implement an alternative design of GNRFET -based 6T SRAM cell with doped reservoirs that also supports process variation. In addition, multi-threshold technology optimizes the performance of the proposed cell. The proposed design provides a means to analyze delay and power of GNRFET-based SRAM under process variation with considering edge roughness, and offers design and fabrication insights for cell in the future.

The purpose of this paper is to propose a leakage reduction technique which will works for complementary metal oxide semiconductor (CMOS) and fin field effect transistor (FinFET). Power consumption will always remain one of the major concerns for the integrated circuit (IC) designers. Presently, leakage power dominates the total power consumption, which is a severe issue. It is undoubtedly clear that the scaling of CMOS revolutionizes the IC industry. Still, on the contrary, scaling of the size of the transistor has raised leakage power as one of the significant threats to the IC industry. Scaling of the devices leads to the scaling of other device parameters, which includes threshold voltage also. The scaling of threshold voltage leads to an exponential increase in the sub-threshold current. So, many leakage reduction techniques have been proposed by researchers for CMOS from time to time. Even the other nano-scaled devices such as FinFET, carbon nanotube field effect transistor and tunneling field effect transistor, have been introduced, and FinFET is the one which has evolved as the most favorable candidate for replacing CMOS technology.

Because of its minimum leakage and without having limitation of the short channel effects, it gradually started replacing the CMOS. In this paper, the authors have proposed a technique for leakage reduction for circuits using nano-scaled devices such as CMOS and FinFET. They have compared the proposed PMOS FOOTER SLEEP with the existing leakage reduction techniques such as LECTOR technique, LECTOR FOOTER SLEEP technique. The proposed technique has been implemented using CMOS and FinFET devices. This study found that the proposed method reduces the average power, as well as leakage power reduction, for both CMOS and FinFET devices.

This study found that the proposed method reduces the average power as well as leakage power reduction for both CMOS and FinFET devices. The delay has been calculated for the proposed technique and the existing techniques, which verifies that the proposed technique is suitable for high-speed circuit applications. The authors have implemented higher order gates to verify the performance of the proposed circuit. The proposed method is suitable for deep-submicron CMOS technology and FinFET technology.

All the existing techniques were proposed for either CMOS device or FinFET device, but the authors have implemented all the techniques with both the devices and verified with the proposed technique for CMOS as well as FinFET devices.

In complementary metal-oxide-semiconductor (CMOS) logic circuits, there is a direct square proportion of supply voltage on dynamic power. If the supply voltage is high, then more amount of energy will be consumed. Therefore, if a low voltage supply is used, then dynamic power will also be reduced. In a mixed signal circuit, there can be a situation when lower voltage circuitry has to drive large voltage circuitry. In such a case, P-type metal-oxide-semiconductor of high-voltage circuitry may not be switched off completely by applying a low voltage as input. Therefore, there is a need for level shifter where low-voltage and high-voltage circuits are connected. In this paper the multi-scaling voltage level shifter is presented which overcomes the contention problems and suitable for low-power applications.

The voltage level shifter circuit is essential for digital and analog circuits in the on-chip integrated circuits. The modified voltage level shifter and reported energy-efficient voltage level shifter have been optimally designed to be functional in all process voltage and temperature corners for VDDH = 5V, VDDL = 2V and the input frequency of 5 MHz. The modified voltage level shifter and reported shifter circuits are implemented using Cadence Virtuoso at 90 nm CMOS technology and the comparison is made based on speed and power consumed by the circuit.

The voltage level shifter circuit discussed in this paper removes the contention problem that is present in conventional voltage level shifter. Moreover, it has the capability for up and down conversion and reduced power and delay as compared to conventional voltage level shifter. The efficiency of the circuit is improved in two ways, first, the current of the pull-up device is reduced and second, the strength of the pull-down device is increased.

The modified level shifter is faster for switching low input voltage to high output voltage and also high input voltage to low output voltage. The average power consumption for the multi-scaling voltage level shifter is 259.445 µW. The power consumption is very less in this technique and it is best suitable for low-power applications.

This paper aims to describe the fabrication and characterization of current mirror-integrated microelectromechanical systems (MEMS)-based pressure sensor.

The integrated pressure-sensing structure consists of three identical 100-µm long and 500-µm wide n-channel MOSFETs connected in a resistive loaded current mirror configuration. The input transistor of the mirror acts as a constant current source MOSFET and the output transistors are the stress sensing MOSFETs embedded near the fixed edge and at the center of a square silicon diaphragm to sense tensile and compressive stresses, respectively, developed under applied pressure. The current mirror circuit was fabricated using standard polysilicon gate complementary metal oxide semiconductor (CMOS) technology on the front side of the silicon wafer and the flexible pressure sensing square silicon diaphragm, with a length of 1,050 µm and width of 88 µm, was formed by bulk micromachining process using tetramethylammonium hydroxide solution on the backside of the wafer. The pressure is monitored by the acquisition of drain voltages of the pressure sensing MOSFETs placed near the fixed edge and at the center of the diaphragm.

The current mirror-integrated pressure sensor was successfully fabricated and tested using in-house developed pressure measurement system. The pressure sensitivity of the tested sensor was found to be approximately 0.3 mV/psi (or 44.6 mV/MPa) for pressure range of 0 to 100 psi. In addition, the pressure sensor was also simulated using Intellisuite MEMS Software and simulated pressure sensitivity of the sensor was found to be approximately 53.6 mV/MPa. The simulated and measured pressure sensitivities of the pressure sensor are in close agreement.

The work reported in this paper validates the use of MOSFETs connected in current mirror configuration for the measurement of tensile and compressive stresses developed in a silicon diaphragm under applied pressure. This current mirror readout circuitry integrated with MEMS pressure-sensing structure is new and fully compatible to standard CMOS processes and has a promising application in the development CMOS-MEMS-integrated smart sensors.

The purpose of this paper is to offer an introduction to the technological advances of the complementary metal–oxide–semiconductor (CMOS) image sensors along the past decades. The authors review some of those technological advances and examine potential disruptive growth directions for CMOS image sensors and proposed ways to achieve them.

Those advances include breakthroughs on image quality such as resolution, capture speed, light sensitivity and color detection and advances on the computational imaging.

The current trend is to push the innovation efforts even further, as the market requires even higher resolution, higher speed, lower power consumption and, mainly, lower cost sensors. Although CMOS image sensors are currently used in several different applications from consumer to defense to medical diagnosis, product differentiation is becoming both a requirement and a difficult goal for any image sensor manufacturer. The unique properties of CMOS process allow the integration of several signal processing techniques and are driving the impressive advancement of the computational imaging.

The authors offer a very comprehensive review of methods, techniques, designs and fabrication of CMOS image sensors that have impacted or will impact the images sensor applications and markets.

This article aims to present complete analysis of energy losses in complementary metal-oxide semiconductor (CMOS) circuits and the effectiveness of dynamic voltage and frequency scaling (DVFS) as a method of energy conservation in CMOS circuits in variety of technologies. Energy efficiency in CMOS devices is an issue of highest importance with still continuing technology scaling. There are powerful tools for energy conservation in form of dynamic voltage scaling (DVS) and dynamic frequency scaling (DFS).

Using analytical equations and Spice models of various technologies, energy losses are calculated and effectiveness of DVS and DFS is evaluated for every technology.

Test showed that new dedicated technology for low static energy consumption can be as economical as older technologies. The dynamic voltage and frequency scaling are most effective when there is a dominance of dynamic energy losses in circuit. In case when static energy losses are comparable to dynamic energy losses, use of dynamic voltage frequency scaling can even lead to increased energy consumption.

This paper presents complete analysis of energy losses in CMOS circuits and effectiveness of mentioned methods of energy conservation in CMOS circuits in six different technologies.

The purpose of this work is to reduce the power consumption of KSA and to improve the PDP for data path applications. In digital Very Large – Scale Integration systems, the addition of two numbers is one of the essential functions. This arithmetic function is used in the modern digital signal processors and microprocessors. The operating speed of these processors depends on the computation of the arithmetic function. The speed computation block for most of the datapath elements was adders. In this paper, the Kogge–Stone adder (KSA) is designed using XOR, AND and proposed OR gates. The proposed OR gate has less power consumption due to the less number of transistors. In arithmetic logic circuit power, delay and power delay products (PDP) are considered as the important parameters. The delays reported for the proposed OR gate are less when compared with the conventional Complementary Metal Oxide Semiconductor (CMOS) OR gate and pre-existing logic styles. The proposed circuits are optimized in terms of power, delay and PDP. To analyze the performance of KSA, extensive Cadence Virtuoso simulations are used. From the simulation results based on 45 nm CMOS process, it was observed that the proposed design has obtained 688.3 nW of power consumption, 0.81 ns of delay and 0.55 fJ of PDP at 1.1 V.

In this paper, a new circuit for OR gate is proposed. The KSA is designed using XOR, AND and proposed OR gates.

The proposed OR gate has less power consumption due to the less number of transistors. The delays reported for the proposed OR gate are less when compared with the conventional CMOS OR gate and pre-existing logic styles. The proposed circuits are optimized in terms of power, delay and PDP.

In arithmetic logic circuit power, delay and PDP are considered as the important parameters. In this paper, a new circuit for OR gate is proposed. The power consumption of the designed KSA using the proposed OR gate is very less when compared with the conventional KSA. Simulation results show that the performance of the proposed KSA are improved and suitable for high speed applications.

The purpose of this paper is to design and implement a fully integrated low‐phase noise and large tuning range dual‐band LC voltage‐controlled oscillator (VCO) in 0.13 μm complementary metal oxide semiconductor (CMOS) technology.

Two parallel‐connected single‐band VCOs are designed to implement the proposed VCO. Adopting a simple and straight‐forward architecture, the dual‐band VCO is configured to operate at two frequency bands, which are from 1.48 GHz to 1.78 GHz and from 2.08 GHz to 2.45 GHz. A band selection circuit is designed to perform band selection process based on the controlling input signal.

The proposed VCO features phase noise of −104.7 dBc/Hz and −108.8 dBc/Hz at 1 MHz offset frequency for both low corner and high corner end of the low‐band operation. For high‐band operation, phase‐noise performance of −101.1 dBc/Hz and −110.4 dBc/Hz at 1 MHz offset frequency are achieved. The measured output power of the dual‐band VCO ranges from −8.4 dBm to −5.8 dBm and from −9.6 dBm to −8.0 dBm for low‐band and high‐band operation, respectively. It was also observed that the power differences between the fundamental spectrum and the nearby spurious tone range from −67.5 dBc to −47.7 dBc.

The paper is useful to both the academic and industrial fields since it promotes the concept of multi‐band or multi‐standard system which is currently in demand in the telecommunication industry.