Search results

The present paper aims to propose a basic current mirror-sensing circuit as an alternative to the traditional Wheatstone bridge circuit for the design and development of high-sensitivity complementary metal oxide semiconductor (CMOS)–microelectromechanical systems (MEMS)-integrated pressure sensors.

This paper investigates a novel current mirror-sensing-based CMOS–MEMS-integrated pressure-sensing structure based on the piezoresistive effect in metal oxide field effect transistor (MOSFET). A resistive loaded n-channel MOSFET-based current mirror pressure-sensing circuitry has been designed using 5-μm CMOS technology. The pressure-sensing structure consists of three identical 10-μm-long and 50-μm-wide n-channel MOSFETs connected in current mirror configuration, with its input transistor as a reference MOSFET and output transistors are the pressure-sensing MOSFETs embedded at the centre and near the fixed edge of a silicon diaphragm measuring 100 × 100 × 2.5 μm. This arrangement of MOSFETs enables the sensor to sense tensile and compressive stresses, developed in the diaphragm under externally applied pressure, with respect to the input reference transistor of the mirror circuit. An analytical model describing the complete behaviour of the integrated pressure sensor has been described. The simulation results of the pressure sensor show high pressure sensitivity and a good agreement with the theoretical model has been observed. A five mask level process flow for the fabrication of the current mirror-sensing-based pressure sensor has also been described. An n-channel MOSFET with aluminium gate was fabricated to verify the fabrication process and obtain its electrical characteristics using process and device simulation software. In addition, an aluminium gate metal-oxide semiconductor (MOS) capacitor was fabricated on a two-inch p-type silicon wafer and its CV characteristic curve was also measured experimentally. Finally, the paper presents a comparative study between the current mirror pressure-sensing circuit with the traditional Wheatstone bridge.

The simulated sensitivities of the pressure-sensing MOSFETs of the current mirror-integrated pressure sensor have been found to be approximately 375 and 410 mV/MPa with respect to the reference transistor, and approximately 785 mV/MPa with respect to each other. The highest pressure sensitivities of a quarter, half and full Wheatstone bridge circuits were found to be approximately 183, 366 and 738 mV/MPa, respectively. These results clearly show that the current mirror pressure-sensing circuit is comparable and better than the traditional Wheatstone bridge circuits.

The concept of using a basic current mirror circuit for sensing tensile and compressive stresses developed in micro-mechanical structures is new, fully compatible to standard CMOS processes and has a promising application in the development of miniaturized integrated micro-sensors and sensor arrays for automobile, medical and industrial applications.

This paper aims to characterize the relationship between the interelectrode capacitance (C) of metal-oxide-semiconductor field-effect transistors (MOSFETs) and the applied bias voltage (V) by a fractional-order equivalent model.

A Riemann–Liouville-type fractional-order equivalent model is proposed for the C–V characteristic of MOSFETs, which is based on the mathematical relationship between fractional calculus and the semiconductor physical model for the interelectrode capacitance of metal oxide semiconductor structure. The C–V characteristic data of an N-channel MOSFET are obtained by Silvaco TCAD simulation. A differential evolution-based offline scheme is exploited for the parameter identification of the proposed model.

According to the results of theoretical analysis, mathematical derivation, simulation and comparison, this paper illustrates that, along with the variation of bias voltage applied, the interelectrode capacitance (C) of MOSFETs performs a fractional-order characteristic.

This work uncovers the fractional-order characteristic of MOSFETs’ interelectrode capacitance. By the proposed model, the influence of doping concentration on the gate leakage parasitic capacitance of MOSFETs can be revealed. In the pre-defined doping concentration range, the relative error of the proposed model is less than 5% for the description of C–V characteristics of metal-oxide-semiconductor field-effect transistors (MOSFETs). Compared to some existing models, the proposed model has advantages in both model accuracy and model complexity, and the variation of model parameters can directly reflect the relationship between the characteristics of MOSFETs and the doping concentration of materials. Accordingly, the proposed model can be used for the microcosmic mechanism analysis of MOSFETs. The results of the analysis produce evidence for the widespread existence of fractional-order characteristics in the physical world.

This paper aims to describe the fabrication and characterization of current mirror-integrated microelectromechanical systems (MEMS)-based pressure sensor.

The integrated pressure-sensing structure consists of three identical 100-µm long and 500-µm wide n-channel MOSFETs connected in a resistive loaded current mirror configuration. The input transistor of the mirror acts as a constant current source MOSFET and the output transistors are the stress sensing MOSFETs embedded near the fixed edge and at the center of a square silicon diaphragm to sense tensile and compressive stresses, respectively, developed under applied pressure. The current mirror circuit was fabricated using standard polysilicon gate complementary metal oxide semiconductor (CMOS) technology on the front side of the silicon wafer and the flexible pressure sensing square silicon diaphragm, with a length of 1,050 µm and width of 88 µm, was formed by bulk micromachining process using tetramethylammonium hydroxide solution on the backside of the wafer. The pressure is monitored by the acquisition of drain voltages of the pressure sensing MOSFETs placed near the fixed edge and at the center of the diaphragm.

The current mirror-integrated pressure sensor was successfully fabricated and tested using in-house developed pressure measurement system. The pressure sensitivity of the tested sensor was found to be approximately 0.3 mV/psi (or 44.6 mV/MPa) for pressure range of 0 to 100 psi. In addition, the pressure sensor was also simulated using Intellisuite MEMS Software and simulated pressure sensitivity of the sensor was found to be approximately 53.6 mV/MPa. The simulated and measured pressure sensitivities of the pressure sensor are in close agreement.

The work reported in this paper validates the use of MOSFETs connected in current mirror configuration for the measurement of tensile and compressive stresses developed in a silicon diaphragm under applied pressure. This current mirror readout circuitry integrated with MEMS pressure-sensing structure is new and fully compatible to standard CMOS processes and has a promising application in the development CMOS-MEMS-integrated smart sensors.

This paper aims to describe the fabrication, packaging and testing of a resistive loaded p-channel metal-oxide-semiconductor field-effect transistor-based (MOSFET-based) current mirror-integrated pressure transducer.

Using the concept of piezoresistive effect in a MOSFET, three identical p-channel MOSFETs connected in current mirror configuration have been designed and fabricated using the standard polysilicon gate process and microelectromechanical system (MEMS) techniques for pressure sensing application. The channel length and width of the p-channel MOSFETs are 100 µm and 500 µm, respectively. The MOSFET M1 of the current mirror is the reference transistor that acts as the constant current source. MOSFETs M2 and M3 are the pressure-sensing transistors embedded on the diaphragm near the mid of fixed edge and at the center of the square diaphragm, respectively, to experience both the tensile and compressive stress developed due to externally applied input pressure. A flexible square diaphragm having a length of approximately 1,000 µm and thickness of 50 µm has been realized using deep-reactive ion etching of silicon on the backside of the wafer. Then, the fabricated sensor chip has been diced and mounted on a TO8 header for the testing with pressure.

The experimental result of the pressure sensor chip shows a sensitivity of approximately 0.2162 mV/psi (31.35 mV/MPa) for an input pressure of 0-100 psi. The output response shows a good linearity and very low-pressure hysteresis. In addition, the pressure-sensing structure has been simulated using the parameters of the fabricated pressure sensor and from the simulation result a pressure sensitivity of approximately 0.2283 mV/psi (33.11 mV/MPa) has been observed for input pressure ranging from 0 to 100 psi with a step size of 10 psi. The simulated and experimentally tested pressure sensitivities of the pressure sensor are in close agreement with each other.

This current mirror readout circuit-based MEMS pressure sensor is new and fully compatible to standard CMOS processes and has a promising application in the development CMOS-MEMS-integrated smart sensors.

Developments in neutron detection technology during the past three years are reviewed with special emphasis on application to safety, security, or industrial development.An investigation about the possibility of using N‐channel power MOSFET (metal oxide semiconductor field effect transistor) as a high‐energy neutron sensitive detector is presented here. An empirical expression for neutron fluence detection is derived from the relation between neutron fluence and the evolution of the transistor current measured in the saturation region. This expression is valid for neutron fluence in the range 5×10⁹–1×10¹⁴ n cm⁻².

This article shows that irradiation with neutrons can be used as solution to harden commercial (COTS: Commercial‐Off‐The‐Shelf) n‐channel power MOSFET (Metal Oxide Semiconductor Field Effect Transistor) devices against destructive events induced by heavy ion irradiation. Atomic displacements created in silicon, by neutron irradiations, result in traps and recombination centers which reduce the electron‐hole pairs density generated by the heavy ion within the device. These results highlight a strong reduction in the photo‐current generated by the heavy ion, correlated with a reduction of the carrier lifetime.

This paper aims to propose a low-power complementary MOS (CMOS) current sensor for control circuit in an integrated DC-DC buck converter.

The integrated DC-DC converter, which is composed of feedback control circuit and power block, is designed with 0.35-µm CMOS process. Current sensor in the control circuit is integrated with sense-FET and voltage-follower circuits to reduce power consumption and improve its sensing accuracy. In the current-sensing circuit, the size ratio of the power metal oxide semiconductor field effect transistor (MOSFET) to the sensing transistor (K) is 1,000, and a current-mirror is used for a voltage follower. N-channel MOS acts as a switching device in the current-sensing circuit, where the sensing FET is in parallel with the power MOSFET. The amplifier and comparator are designed to obtain a high gain and a fast transient time.

Experiment shows that the current sensor is operated with accuracy of more than 85 per cent, and the transient time of the error amplifier is controlled within 100 µs. The sensing current is in the range of a few hundred µA at a frequency of 0.6-2 MHz and an input voltage of 3-5 V. The output voltage is obtained as expected with the ripple ratio within 5 per cent.

The proposed current sensor in DC-DC converter provides an accurately sensed inductor current with a significant reduction in power consumption in the range of 0.2 mW. High-accuracy regulation is obtained using the proposed current sensor. As the sensor utilizes simple switch-type voltage follower and sense-FET, it can be widely applied to other low-power applications such as high-frequency oscillator and over-current protection circuit.

The purpose of this paper is to study the effects of positive and negative bias stressing on switching performance of power VDMOSFETs used in communication systems.

A positive and a negative high‐field stress are applied on the gate oxide of MOS devices and electrical characterization is performed after each period of stress, a comparison is presented.

Compared results between the two types of stress show that certain doses of stress can increase the device speed. The underlying changes of the threshold voltage under these two types of stress are referred to as the variation of the gate oxide‐trapped charge and interface trap densities.

This paper presents new and original experiments run over a number of metal‐oxide semiconductor field effect transistor devices to compare the effects of the direction of the applied field on the degradation and the reliability of these structures.

The purpose of this paper is to develop analytical model for gate tunneling current for an ultra‐thin gate oxide n‐channel MOSFET with inevitable nano scale effects (NSE).

A computationally efficient model for gate tunneling current for an ultra‐thin gate oxide n‐channel MOSFET in nano scale is presented. The model predictions are compared with the two‐dimensional Sentaurus device simulation.

Good agreement between the model and experimental data was obtained. The model also shows good agreement when compared with Sentaurus simulation and available model. It is observed that neglecting NSE may lead to large error in the calculated gate tunneling current. The findings provide a guideline to the severity of NSE from the point of view of standby power consumption. It is found that temperature and substrate bias have almost negligible effect on gate tunneling current. The gate tunneling current variation with gate bias, gate oxide thickness and source/drain overlap region have also been assessed.

The present work is concentrated only on the gate leakage current and is useful for gate leakage analysis of the circuits.

The model so developed is conceptually simple, numerically efficient and can be used for circuit simulator.

NSE are considered while modeling the gate tunneling current through nano scale n‐channel MOSFET.

This paper aims to propose a new fin field-effect transistor (FinFET)-based domino technique low-power series connected foot-driven transistors logic in 32 nm technology and examine its performance parameters by performing transient analysis.

In the proposed technique, the leakage current is reduced at footer node by a division of current to improve the performance of the circuit in terms of average power consumption, propagation delay and noise margin. Simulation of existing and proposed techniques are carried out in FinFET and complementary metal-oxide semiconductor technology at FinFET 32 nm technology for 2-, 4-, 8- and 16-input domino OR gates on a supply voltage of 0.9 V using HSPICE.

The proposed technique shows maximum power reduction of 77.74% in FinFET short gate (SG) mode in comparison with current-mirror-based process variation tolerant (CPVT) technique and maximum delay reduction of 51.34% in low power (LP) mode in comparison with CPVT technique at a frequency of 100 MHz. The unity noise gain of the proposed circuit is 1.10× to 1.54× higher in comparison with different existing techniques in FinFET SG mode and 1.11× to 1.71× higher in FinFET LP mode. The figure of merit of the proposed circuit is up to 15.77× higher in comparison with existing domino techniques.

The research proposes a new FinFET-based domino technique and shows improvement in power, delay, area and noise performance. The proposed design can be used for implementing high-speed digital circuits such as microprocessors and memories.