Search results

In recent times, the usage of elastane-containing denim garments has increased, as it provides fit and comfort both at the same time. The purpose of the study is to understand the effect of abrasion on the durability of comfort related to body movement and shape retention property of the stretch-denim fabric.

The paper investigates the effect of abrasion on the initial tensile properties, recovery and resilience properties of the stretch-denim fabric. Further, to analyse the effect of the composition of the elastane yarn, three different types of elastane yarns having different types of sheath (covering) fibre, structure and different levels of elastane content have been used in the weft.

The comfort related to body movement and the shape retention properties of the stretch-denim fabric got affected due to abrasive damage. The elastane yarn composition and structure played an important role in determining the extent of the change in such properties during abrasion. The fabric with a higher level of elastane content suffered a greater loss in shape-retention properties due to abrasion. The extent of mass loss in stretch-denim fabric does not always correlate to the extent of loss in the comfort and shape-retention properties.

Most of the earlier studies have investigated the effect of abrasion on the durability aspect of the stretch-denim fabric. In a practical scenario, the stretch-denim garments are rarely discarded due to tearing or change in appearance but mainly due to bagging, i.e. distortion in shape after usage. Thus, the study on the combined effect of the abrasion and cyclic loading on the comfort and shape-retention properties will help to predict the performance of the apparel during usage.

In recent times, stretch denim garments have become very popular amongst consumers as the garment is able to provide body fit and body comfort at the same time. The purpose of this study is to investigate the effect of abrasion on the change in surface appearance, mass loss and ultimate tensile properties of the stretch denim fabric in different directions (warp, weft and biased).

After abrading the fabrics in three different directions (warp, weft and biased), the loss in ultimate tensile properties, mass loss and surface appearance has been investigated in the respective directions of abrasion (warp, weft and biased). The study also encompasses the effect of different types of stretch yarn with varying levels of elastane content on such unidirectional abrasive damage.

It is seen that with the same level of abrasion cycles, the fabric's response in terms of mass loss and loss in ultimate tensile properties are different in different directions. The mass loss due to abrasion in biased direction is found to be minimum. The loss in ultimate tensile properties due to abrasion was highest in the weft direction. It is also found that the higher mass loss due to abrasion does not always result in a greater loss in ultimate tensile properties. The composition and the structure of the weft yarn significantly affected the extent of the mass loss and the loss in ultimate tensile properties during abrasive damage.

The impact of abrasive damage in terms of mass loss and loss in tensile strength along the different directions of denim fabric has not been explored till date. Abrasion of fabric can be done both in multi-direction (Lissajous motion) as well as in uni-direction (linear motion). The multidirectional abrasion provides a holistic or comprehensive idea of the fabric's response to the abrasive damage but does not take into consideration the fabric's anisotropic response to the abrasive damage. Most of the earlier investigation related to abrasive damage of denim fabric has been done in instruments where the motion of the abrader is multidirectional (Lissajous) in nature. For greater depth of understanding about the fabric performance under abrasive damage along the various direction (warp, weft and biased), unidirectional abrasion is conducted in this study.

The purpose of this review paper is to define the dominating factors (such as fiber, yarn, fabric structure, sewing thread, sewing needle and machine parameters) that affect the seam damages and causing defects. It also describes the various explanations of sewing defects in garment production and critically analyzes them for optimum selection of parameters and speeds for minimizing such faults. Hence, the knowledge of various factors which affect the sewing damages/defects will be helpful for garment manufacturers/researchers to know influence of the parameters and control the quality of producing seam.

This section is not applicable for a review paper.

Sewing damages such as needle cut and other sewing damages/defects are studied mostly in woven fabric. There are very few studies conducted on knitted fabric sewing damages/defects. The sewing damage problems do not have single solution that is capable of removing these damages in fabric. All the determined and affecting parameters related to fiber, yarn, fabric construction, sewing thread and sewing machine must be examined to design appropriate remedial measurement related to machine design, fabric parameters and sewing thread. This could help in minimizing or eliminating the needle cut and other sewing damage problems.

It is an original review work and is helpful for garment manufacturers/researchers to reduce the defects and be able to produce good quality seam.

The purpose of this research is to study the effect of softener treatment on plain jersey fabrics with properties made of cotton and spandex yarn.

Samples with 100 percent cotton yarns, spandex yarns in alternating courses (half plating) and spandex yarns in every courses (full plating) were produced on a circular knitting machine where the two latter cases were produced at five different levels of spandex extension. After the dyeing process, fabrics were treated with fabric softener using two softener types (cationic and silicon) and all type two concentrations (3 percent, 6 percent) to evaluate the most appropriate softener type and concentration on fabric friction force, sewing needle penetration force and weight loss percent under different levels of spandex extension.

Results showed that silicon softener treatment results in high decreases in fabric sewing needle penetrating force, friction force and while treatment with cationic softener results in high decreases in weight loss percent for 100 percent cotton, half and full plating fabrics.

There is a growing need to study the effect of softeners when spandex yarns are used in the production of knitted fabric which results in high increase of stitch density. This research compares the effects of two different softener types at different concentrations on the properties of both plain jersey fabric produced from 100 percent cotton yarns and from cotton/spandex yarns with different stitch density.

Air permeability has a valuable role in comfort parameters. It is known that air permeability of elastomeric yarns is firmly low. Despite that, usage of elastomeric inlay-yarns is the most common and the most effective way to generate compression for knitted textile. This study aims to investigate the influence of elastomeric inlay-yarn linear density, insertion density and elongation of the sample to the air permeability of compression knitted materials.

Two different types of knitting patterns were investigated: rib 1 × 1 pattern with different elastomeric inlay-yarn linear density (four variants) and insertion density (without inlay yarn and with inlay-yarns inserted into every single, second or fourth course) and combined laid-in jacquard pattern. The air permeability test for these structures was performed without any deformation and at 10 and 20 per cent fixed transverse elongation.

According to the investigation, insertion density of inlay-yarns has a huge impact on air permeability; however, air permeability of knitted material is not linearly proportional to the total amount of inlay-yarns. Also, it was found that air permeability increases by increasing elongation, regardless of knitting pattern and total amount of elastomeric inlay-yarn in the knitted structure. Alteration of the loop geometry at natural state and 20 per cent fixed elongation was established, and the increase of air permeability at fixed elongation may be dependent on changes of knitted material porosity.

According to the obtained results, recommendations to perform air permeability measurement at least with minimal specific wear elongation are presented.

Examines the tenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

The purpose of this paper is to investigate the thermal transfer properties of electric heating fabric system which contains heating units or conductive yarns by numerical simulation, in order to optimize and evaluate the thermal performance of heating clothing.

Two kinds of FEM models are created by ANSYS system: macro-scale models of the fabrics system with heating units and air layer; and meso-scale models of the plain-woven fabrics were established embedded with the stainless yarns. In the macro-scale model, the interior and surface temperature field distribution were simulated and analyzed based on different heating unit size, heating power, heating region, air layer thickness and ambient temperature. For meso-scale models, the effects of the conductive yarns temperature, covering fabrics and pore-filling material on the temperature field distribution were simulated and analyzed.

With the increasing of the air layer thickness or the effective conductivity, the heat transfer along the direction of fabric thickness decreases gradually. The heat transfer along the fabric plane can be increased by dispersing the heating region. With the increasing of the conductive yarns’ temperature or the covering fabrics’ conductivity, the heat transfer distance along the fabric warp direction can be increased. Filling the internal pores of the fabric with 10 wt% SiC/TPU hybrid materials can effectively increase the in-plane heat transfer and improve the temperature uniformity on the surface of heated fabrics.

The finite element method was used to establish the simulation models of the heating fabric systems. The influence of several parameters on the thermal performance was analyzed and discussed, as well as the internal and external temperature distribution in the macro and micro scales models.

Examines the fourteenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

The purpose of this research was to investigate the effect of knit fabric stitch patterns, as indicated by fabric thickness variations, on moisture responsiveness for different seamless knitted wool-based fabrics.

Forty fabrics were created on a Santoni Top-2 circular knitting machine by using combinations of jersey, tuck and float stitches in combinations of wool/Nylon, wool, and spandex yarns. Physical properties of the knit fabrics as well as changes in fabric thickness during dry, wet, after 30 min air-drying and after 60 min air-drying conditions were compared. Repeated measures ANOVA tests and bivariate correlation analysis were conducted.

The results indicated that changes in moisture conditions had a significant effect on fabric thickness, and these changes differed by stitch pattern groups. Float patterns and tuck/rib patterns showed a continued relaxation of fabric thickness through all conditions, but tuck stitches and rib stitches showed a thickness recovery. Wool swatches, unlike the wool/Nylon swatches, increased their average thickness in after 60 min air-drying condition compared to 30 min air-drying condition.

This research documents the moisture responsive properties for wool based yarns, as emerging natural functional materials for seamless knitting industry, with applications in garments for activewear as well as healthcare.

The main objectives of this research work were to investigate the effect of production speed on intermingled yarn properties and melange fabric properties with special reference to melange appearance.

Polyester/nylon intermingled yarns were produced using an SSM DP3-C air-intermingling machine using commercial process parameters and Heberlein P212 nozzle. Melange fabric samples were knitted from polyester/nylon intermingled yarns while maintaining the same parameters to avoid knitting variations. The fabric samples were dyed using a sample dyeing machine while maintaining dye recipe and dyeing parameters constant to avoid dyeing variations.

The production speed has significant effect on intermingled yarn and melange fabric properties. When the production speed is increased, mingle points, mingle stability, linear density, strength and the elongation of the intermingled yarns decreases. When the production speed is increased, fabric weight decreases and the melange effect varies from dot-like appearance to line-like appearance.

Only the effect of production speed on intermingled yarn and melange fabric properties is discussed in this paper. Appearance evaluating systems developed in this research are limited to melange fabrics produced using air-intermingled yarns with two colour components.

Results indicate that the intermingled yarns for the application of melange fabrics should be developed with optimum intermingling speeds, and it should not be changed during the production since production speed has significant effect on yarn and fabric parameters. Therefore, melange appearance and fabric weight may vary between fabric lots with different production speeds even though all the other parameters are kept constant. Further, melange appearance evaluation method developed in this research could be used as a guide in developing melange fabrics.

This research introduced a qualitative and a quantitative method to analyse melange fabric appearance. This melange appearance evaluation method can be used as a guide to achieve specific melange effect in the sample development stage. Further, when a melange sample appearance catalogue is developed for all the variables for a particular fabric type using this evaluation method, customer requested appearance can be achieved in minimum sample trials which save time, capacity, money and customer credibility.