Search results
1 – 10 of 102Aya Qatawna, Rabab Allouzi and Samih Qaqish
The primary objective of this study is to produce one-way slabs made of LWFC with low density and sufficient compressive strength suitable for structural purpose then investigate…
Abstract
Purpose
The primary objective of this study is to produce one-way slabs made of LWFC with low density and sufficient compressive strength suitable for structural purpose then investigate their flexural behavior under various types of reinforcement and thickness of the slab and the influence of addition of PP fibers reinforcement on the mechanical behavior of reinforced concrete slabs. The specimens were tested using four-point loading. The results concerning load capacity, deflection and failure mode and crack pattern for each specimen were obtained. Also, an analytical investigation of PP fiber and GFG contribution on the flexural behavior of foamed concrete slabs is studied to investigate the significant role of PP fiber on the stress distribution in reinforced foam concrete and predict the flexural moment capacity.
Design/methodology/approach
The materials used in this study are cement, fine aggregate (sand), water, PP fibers, foaming agent, chemical additives if required, steel reinforcing rebars and glass fiber grid. The combination of these constituent materials will be used to produce foamed concrete in this research Then this study will present the experimental program of one-way foamed concrete slabs including slabs reinforced with GFR grids and another with steel reinforcements. The slabs will be tested in the laboratory under static loading conditions to investigate their ultimate capacities. The flexural behavior is to the interest of the slabs reinforced with GFR grids reinforcements in comparison with that of one with steel reinforcing rebars. Three groups are considered. (1) Group I: two slabs of PP fiber foamed concrete with minimum required reinforcements. (2) Group II: two slabs of PP fiber foamed concrete with glass fiber grids. (3) Group III: two slabs of PP fiber foamed concrete with the minimum required reinforcements and glass fiber grids.
Findings
The experimental results proved the effectiveness and efficiency of this the new system in producing a low density of concrete below 1900 kg/m3 had a corresponding strength of about 17 MPa at least. Besides, the presence of PP fibers had a noticeable improvement on the flexural strength values for all the examined slabs. It was found that the specimens reinforced with steel reinforcement mesh carried higher flexural capacity compared to these reinforced with GFG only. The specimens reinforced with GFG exhibited the lowest flexural capacity due to GFG separation from the concrete substrate. Also, an analytical investigation to predict the flexural strength of all tested specimens was carried out. The analytical results were agreed with the experimental results. Therefore, LWFC can be used as a substitute lightweight concrete material for the production of structural concrete applications in the construction industries today.
Research limitations/implications
Foamed concrete is a wide field to discuss. To achieve the objectives of the project, the study is focused on the foamed concrete with the following limitations: (1) because the aim of this research is to produce foamed concrete suitable for structural purposes, it is decided to produce mixes within the density range 1300–1900 kg/m3. (2) Simply-supported slabs are of considered. (3) This study also looks out by using GFR and without it.
Originality/value
The main objectives of this study were producing structural foamed concrete slabs and investigate their flexural response for residential uses.
Details
Keywords
P. Gunasekar, Anderson A. and Praveenkumar T.R.
Composite materials have revolutionized the aerospace industry by offering superior structural qualities over traditional elements. This study aims to focus on the development and…
Abstract
Purpose
Composite materials have revolutionized the aerospace industry by offering superior structural qualities over traditional elements. This study aims to focus on the development and testing of bamboo natural fiber-based composites enhanced with SiO2 nanoparticles.
Design/methodology/approach
The investigation involved fabricating specimens with varying nanoparticle compositions (0, 10 and 20%) and conducting tensile, flexural, impact and fracture toughness tests. Results indicated significant improvements in mechanical properties with the addition of nanoparticles, particularly at a 10% composition level.
Findings
This study underscores the potential of natural fiber composites, highlighting their environmental friendliness, cost-effectiveness and improved structural properties when reinforced with nanoparticles. The findings suggest an optimal ratio for nanoparticle integration, emphasizing the critical role of precise mixing proportions in achieving superior composite performance.
Originality/value
The tensile strength, flexural strength, impact resistance and fracture toughness exhibited notable enhancements compared with the 0 and 20% nanoparticle compositions. The 10% composition showed the most promising outcomes, showcasing increased strength across all parameters.
Details
Keywords
Santosh Kumar Sahu, P.S. Rama Sreekanth, Y.P. Deepthi, Quanjin Ma and Tunji John Erinle
This study aims to investigate the mechanical properties of sustainable recycled polypropylene (rPP) composite materials integrated with spherical silicon carbide (SiC) particles.
Abstract
Purpose
This study aims to investigate the mechanical properties of sustainable recycled polypropylene (rPP) composite materials integrated with spherical silicon carbide (SiC) particles.
Design/methodology/approach
A representative volume element (RVE) analysis is employed to predict the Young’s modulus of rPP filled with spherical-shaped SiC at varying volume percentages (i.e. 10, 20 and 30%).
Findings
The investigation reveals that the highest values of Young’s modulus, tensile strength, flexural strength and mode 1 frequency are observed for the 30% rPP/SiC samples, exhibiting increases of 115, 116, 62 and 15%, respectively, compared to pure rPP. Fractography analysis confirms the ductile nature of pure rPP and the brittle behavior of the 30% rPP/SiC composite. Moreover, the RVE method predicts Young’s modulus more accurate than micromechanical models, aligning closely with experimental results. Additionally, results from ANSYS simulation tests show tensile strength, flexural strength and frequency within a 10% error range when compared to experimental data.
Originality/value
This study contributes to the field by demonstrating the mechanical enhancements achievable through the incorporation of sustainable materials like rPP/SiC, thereby promoting environmentally friendly engineering solutions.
Details
Keywords
Dongyang Cao, Daniel Bouzolin, Christopher Paniagua, Hongbing Lu and D.Todd Griffith
Herein, the authors report the effects of printing parameters, joining method, and annealing conditions on the structural performance of fusion-joined short-beam sections produced…
Abstract
Purpose
Herein, the authors report the effects of printing parameters, joining method, and annealing conditions on the structural performance of fusion-joined short-beam sections produced by additive manufacturing.
Design/methodology/approach
The authors first identified appropriate printing parameters for joining segmented short beams and then used those parameters to print and fusion-join segments with different configurations of stiffeners to form a longer section of a wing or small wind turbine blade structure.
Findings
It was found that the beams with three lateral and three base stiffening ribs give the highest flexural strength among the three beams investigated. Results on joined beams annealed at different conditions showed that annealing at 70 °C for 0.5 h yields higher performance than annealing at the same temperature for longer times. It is also found that in the case of the hot-plate-welded three-dimensional (3D)-printed structures, no annealing is needed for reaching a high strength-to-weight ratio, but annealing is helpful for maximizing the modulus-to-weight ratio. Both thermal buckling and edge wrapping were observed under annealing at 70°C for 0.5 h for 3D-printed beams comprising two lateral and four base stiffening plates.
Originality/value
Fusion-joining of additively manufactured segments is needed owing to the constraint in building volume of a typical commercial 3D-printer. However, study of the effect of process parameters is needed to quantify their effect on mechanical performance. This investigation has therefore identified key printing parameters and annealing conditions for fusion-joining short segments to form larger structures, from multiple 3D-printed sections, such as wind blade structures.
Details
Keywords
Fatma Bouzeboudja and Abdelmadjid Si Salem
To contribute to the identification of the parameters influencing the behavior of textile-reinforced concrete (TRC), the purpose of this paper is to investigate the flexural…
Abstract
Purpose
To contribute to the identification of the parameters influencing the behavior of textile-reinforced concrete (TRC), the purpose of this paper is to investigate the flexural behavior of TRC-based plates under four-point bending notably designed in the context of sustainable development and the substitution of mortar components with natural and abundant materials.
Design/methodology/approach
An extensive experimental campaign was focused about two main parameters. The first one emphases the textile reinforcements, such as the number of layers, the nature and the textile mesh size. In the second step, the composition of the mortar matrix was explored through the use of dune sand as a substitute of the river one.
Findings
Test results in terms of load-displacement response and failure patterns were highlighted, discussed and confronted to literature ones. As key findings, an increase of the load-bearing capacity and ductility, comparable to the use of an industrially produced second textile layer was recorded with the use of dune sand in the mortar mix design. The designed ecofriendly samples with economic concerns denote the significance of obtained outcomes in this research study.
Originality/value
The novelty of the present work was to valorize the use of natural dune sand to design new TRC samples to respond to the environmental and economical requirements. The obtained values provide an improved textiles–matrix interface performance compared to classical TRC samples issued from the literature.
Details
Keywords
Kapildeo P. Yadav, Sudipta Ghosh, Sujata Rajak and Amiya K. Samanta
One of the often-employed building constituents in the construction sector is concrete, which involves hydration of cement, leading to the generation of carbon footprints during…
Abstract
Purpose
One of the often-employed building constituents in the construction sector is concrete, which involves hydration of cement, leading to the generation of carbon footprints during its production. Also, massive amount of natural aggregate is illegally mined, which poses serious environmental issues along with ecological misbalance. Researchers are in continuous search of appropriate substitutes to mitigate those challenges and develop innovative concrete mix. Consequently, depletion of natural resources, the disturbances to the environmental and ecological imbalance will reduce. The purpose of this study is to develop a Portland Slag Cement based novel sustainable concrete incorporating Alccofine and Recycled Refractory Brick as fractional replacement of cement and fine aggregate, respectively and evaluate its destructive, non-destructive and microstructural properties.
Design/methodology/approach
M25 grade of concrete adopting 0.45 water-binder proportion, with diverse percentage of Alccofine as fractional substitution of cement and 20% of recycled refractory brick (RRB) as fine aggregate, has been cast and evaluated for diverse mechanical strength following a curing of 7, 14 and 28 days. Scanning electron microscopic analysis has been carried out to study the microstructural changes in the specimens.
Findings
Supplementary use of Alccofine enhanced normal compressive strength of sustainable concrete mix blended with Portland Slag Cement by a large amount at all levels of 7, 14 and 28 days of curing. Test results indicated development of a favourable high-strength sustainable concrete mix by substituting cement with Alccofine.
Originality/value
This manuscript has demonstrated the possibility of developing sustainable concrete blends by incorporating Alccofine 1203 and RRB as partial replacement of Portland Slag Cement and natural fine aggregate, respectively. The strength and potential of concrete incorporating RRB for wider and special application in adverse environmental conditions having higher thermal gradient, as RRB is a valuable waste from high temperature kiln and furnaces. Alccofine 1203 has been included in the concrete mix as an alternative to Portland Slag Cement to improve the mechanical strength properties and durability of concrete intended for adverse environmental application.
Details
Keywords
Rawan Ramadan, Hassan Ghanem, Jamal M. Khatib and Adel M. ElKordi
The purpose of this paper is to check the feasibility of using biomaterial such as of Phragmites-Australis (PA) in cement paste to achieve sustainable building materials.
Abstract
Purpose
The purpose of this paper is to check the feasibility of using biomaterial such as of Phragmites-Australis (PA) in cement paste to achieve sustainable building materials.
Design/methodology/approach
In this study, cement pastes were prepared by adding locally produced PA fibers in four different volumes: 0%, 0.5%, 1% and 2% for a duration of 180 days. Bottles and prisms were subjected to chemical shrinkage (CS), drying shrinkage (DS), autogenous shrinkage (AS) and expansion tests. Besides, prism specimens were tested for flexural strength and compressive strength. Furthermore, a mathematical model was proposed to determine the variation length change as function of time.
Findings
The experimental findings showed that the mechanical properties of cement paste were significantly improved by the addition of 1% PA fiber compared to other PA mixes. The effect of increasing the % of PA fibers reduces the CS, AS, DS and expansion of cement paste. For example, the addition of 2% PA fibers reduces the CS, expansion, AS and DS at 180 days by 36%, 20%, 13% and 10%, respectively compared to the control mix. The proposed nonlinear model fit to the experimental data is appropriate with R2 values above 0.92. There seems to be a strong positive linear correlation between CS and AS/DS with R2 above 0.95. However, there exists a negative linear correlation between CS and expansion.
Research limitations/implications
The PA used in this study was obtained from one specific location. This can exhibit a limitation as soil type may affect PA properties. Also, one method was used to treat the PA fibers.
Practical implications
The utilization of PA fibers in paste may well reduce the formation of cracks and limit its propagation, thus using a biomaterial such as PA in cementitious systems can be an environmentally friendly option as it will make good use of the waste generated and enhance local employment, thereby contributing toward sustainable development.
Originality/value
To the authors best knowledge, there is hardly any research on the effect of PA on the volume stability of cement paste. Therefore, the research outputs are considered to be original.
Details
Keywords
Suehail Aijaz Shah, Manzoor Ahmad Tantray and Jan Mohammad Banday
Durability of concrete can be enhanced by reducing the pore size/volume of pores or by entrapping the pores. This can be achieved by adding concrete admixtures that have particle…
Abstract
Purpose
Durability of concrete can be enhanced by reducing the pore size/volume of pores or by entrapping the pores. This can be achieved by adding concrete admixtures that have particle size finer than cement. In this study, GNP, having particle size much smaller than cement, has been introduced/added to concrete mix to control the pore size in concrete to tape out the contribution of GNP in the durability enhancement of concrete.
Design/methodology/approach
Different concrete mixes, at various water–cement ratios and amounts of graphene, have been manufactured to produce concrete containing three different %ages of GNP, i.e. 0%, 0.05% and 0.1%. To demonstrate the effect on durability of the concrete through the addition of GNP, these concrete samples have been subjected to repeated Freeze-Thaw cycles. Followed by testing after 28 days of curing, including weight loss, water absorption and strength, which are directly related to the durability aspect of concrete.
Findings
It has been observed that the addition of GNP to concrete mixes reduces the weight loss and pore size distribution and enhances tensile and compressive strength of concrete, thereby increasing the durability of concrete in unfavorable circumstances like freeze-thaw i.e. alternate hot and cold weather conditions.
Originality/value
This investigation presents original piece of experimental work conducted on modified concrete (GNP-based concrete). The aim is to construct the civil infrastructure in deep-cold region with increased life span and better performance.
Details
Keywords
Muhammad Haroon, Raja Bilal Nasar Khan and Anwar Khitab
Present work deals with the partial substitution of cement by waste demolished concrete powder (WDP) for reducing the carbon footprints of concrete.
Abstract
Purpose
Present work deals with the partial substitution of cement by waste demolished concrete powder (WDP) for reducing the carbon footprints of concrete.
Design/methodology/approach
Control specimens and the specimens with 20% WDP as fractional substitute of cement were prepared. The waste powder was thermally activated at 825 °C prior to its use in the mix. The prepared specimens were evaluated in terms of density, workability, mechanical strength, Ultrasonic pulse velocity (UPV) and rebound hammer (RH).
Findings
The results showed that with the substitution, the workability of the mix increased, while the density decreased. A decrement within a 20% limit was found in compressive strength. The UPV and RH results were closely linked to the other results as mentioned above.
Research limitations/implications
The study deals with only M15 concrete and the substitution level of only 20% as a baseline.
Practical implications
The concrete containing 20% WDP is lightweight and more workable. Moreover, its strength at 28 days is 14 MPa, only 1 MPa lesser than the characteristic strength.
Social implications
The WDP can be recycled and the dumping in landfills can be reduced. This is an important effort towards the decarbonation of concrete.
Originality/value
Previous literature indicates that the WDP has been frequently used as a partial replacement of aggregates. However, some traces of secondary hydration were also reported. This work considers the effect of partial substitution of cement by the WDP.
Details
Keywords
Solomon Oyebisi, Mahaad Issa Shammas, Hilary Owamah and Samuel Oladeji
The purpose of this study is to forecast the mechanical properties of ternary blended concrete (TBC) modified with oyster shell powder (OSP) and shea nutshell ash (SNA) using deep…
Abstract
Purpose
The purpose of this study is to forecast the mechanical properties of ternary blended concrete (TBC) modified with oyster shell powder (OSP) and shea nutshell ash (SNA) using deep neural network (DNN) models.
Design/methodology/approach
DNN models with three hidden layers, each layer containing 5–30 nodes, were used to predict the target variables (compressive strength [CS], flexural strength [FS] and split tensile strength [STS]) for the eight input variables of concrete classes 25 and 30 MPa. The concrete samples were cured for 3–120 days. Levenberg−Marquardt's backpropagation learning technique trained the networks, and the model's precision was confirmed using the experimental data set.
Findings
The DNN model with a 25-node structure yielded a strong relation for training, validating and testing the input and output variables with the lowest mean squared error (MSE) and the highest correlation coefficient (R) values of 0.0099 and 99.91% for CS and 0.010 and 98.42% for FS compared to other architectures. However, the DNN model with a 20-node architecture yielded a strong correlation for STS, with the lowest MSE and the highest R values of 0.013 and 97.26%. Strong relationships were found between the developed models and raw experimental data sets, with R2 values of 99.58%, 97.85% and 97.58% for CS, FS and STS, respectively.
Originality/value
To the best of the authors’ knowledge, this novel research establishes the prospects of replacing SNA and OSP with Portland limestone cement (PLC) to produce TBC. In addition, predicting the CS, FS and STS of TBC modified with OSP and SNA using DNN models is original, optimizing the time, cost and quality of concrete.
Details