Search results

The paper aims to evaluate the influence of thermo-chemical cycles of oral fluids on the surface attributes (roughness and microhardness) of lithium disilicate glass-ceramic (LDC) crown restorations manufactured with CAD/CAM technology.

There have been 24 LDC crowns manufactured using the CAD/CAM process for their respective preparation dies ply methyl methacrylate (PMMA) of mandibular left second premolar tooth (n = 8 each group). The standard procedure was used to glaze 16 crown samples (Groups 2 and 3).Samples of Group 3 were aged with thermal (563°C and 5563°C) and pH (2–14) cycles. All 24 samples were tested with a Profilometer and a Vicker hardness tester was used for their surface roughness and hardness measurement, respectively.

In statistical examination on SPSS Statistics 20 (IBM) software, of surface roughness values (Ra) and Vicker hardness values from different groups, Tukey HSD test was executed in one-way ANOVA (a = 0.05). The means Ra for groups were accordingly Group 3 > Group1 > Group 2 (p < 0.001). Similarly, micro-hardness was in order of Group 2 > Group 1 > Group 3 (p < 0.001).

The research work does not have any limitations.

Surrounding temperature and pH significantly impact the surface characteristics of lithium disilicate crown restoration. The study also reveals the inverse relationship between surface roughness and surface hardness parameters. The observed results and facts revealed well in agreement with the past research studies.

Lithium disilicate glass-ceramics (LS2 GC) are widely used as dental prosthetics and dental restorations. Based LS2 GC have hardness and translucency similar to that of natural teeth. This study aims to investigate the tribological features of LS2 GC with crystalline volume fraction of 64% and different crystal sizes from 8 µm to 34 µm for different counterparts.

The tribological behavior was investigated using a pin-on-disc tribometer with alumina and tungsten carbide (WC) spheres, applied load of 5 N and sliding speed of 5 cm/s at normal conditions. The coefficient of friction was measured continuously up to 10,000 sliding cycles. The specific wear rate was calculated from tribological and profile measurements. The wear mechanism was investigated by surface morphology analysis.

The coefficient of friction during running-in varied from 0.8 to 1.0 for the alumina counterpart, because of severe wear. Afterwards, it reduced and reached a stationary regime, characterized by a mild wear regime and the formation of a tribolayer formed by the debris. For the WC counterpart, the coefficient of friction curves increased initially with sliding cycles up to a stationary regime. The samples tested against WC presented the lowest specific wear rate (k), and no variation of wear rate with crystal size was observed. For samples tested against the alumina, crystallization and crystal size increased the wear resistance.

This study evaluated the effect of different counterfaces on the tribological properties of the LS2 GC, an important glass-ceramic base for many dental prosthetics and dental restorations, discussing results in light of the contact mechanics. Different specific wear rates, wear regimes and dependence on the glass-ceramic microstructure were observed depending on the counterpart.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2019-0352/

Different technologies may currently be used to produce dental prostheses, such as additive manufacturing and traditional milling. This study aims to evaluate and improve the fabrication process for hot-pressed porcelain dental prostheses and compare the use of masked stereolithography apparatus (MSLA) casting to computer-aided design/computer-aided manufacturing (CAD/CAM) casting. The cost-benefit analysis of producing dental prostheses through various technologies, including additive manufacturing and traditional milling, has not been fully explored. The cost of materials and processes used to produce prostheses varies based on complexity of design and materials used, and long-term effects, such as durability and wear and tear, must be taken into account.

Using key elements of part costs and estimation cost models, a multivariable approach was used to evaluate the practicality of the recommended strategy and process improvement.

The research found that MSLA casting provides a higher return on investment than CAD/CAM casting, and the optimized production process could be more suitable for the size and annual demand for prostheses.

Overall, this study highlights the need for a more comprehensive understanding of the cost-benefit analysis of different dental prosthesis production methods and emphasises the importance of evaluating long-term effects on the cost-benefit analysis.

Although many researchers have widely studied additive manufacturing (AM) as one of the most important industrial revolutions, few have presented a bibliometric analysis of the published studies in this area. This paper aims to evaluate AM research trends based on 4607 publications most cited from year 2010 to 2020.

The research methodology is bibliometric indicators and network analysis, including analysis based on keywords, citation analysis, productive journal, related published papers and authors indicators. Two free available software were employed VOSviewer and Bibexcel.

Keywords analysis results indicate that among the AM processes, Selective Laser Melting and Fused Deposition Modeling techniques, are the two processes ranked on top of the techniques employed and studied with 35.76% and 20.09% respectively. The citation analysis by VOSviewer software, reveals that the medical applications field and the fabrication of metal parts are the areas that interest researchers greatly. Different new research niches, as pharmaceutical industry, digital construction and food fabrication are growing topics in AM scientific works. This study reveals that journals “Materials & design”, “Advanced materials”, “Acs applied materials & interfaces”, “Additive manufacturing”, “Advanced functional materials” and “Biofabrication” are the most productive and influential in AM scientific research.

The results and conclusions of this work can be used as indicators of trends in AM research and/or as prospects for future studies in this area.

This study aims to compare the marginal fit, flexural strength and hardness for a ceramic premolar that is constructed using dental computer aided machining (CAM) and three-dimensional slurry printing (3DSP).

Dental CAM and 3DSP are used to fabricate a premolar model. To reduce the fabrication time for 3DSP, a new composition of solvent-free slurry is proposed. Before it is fabricated, the dimensions of the green body for the premolar model are enlarged to account for the shrinkage ratio. A two-stage sintering process ensures accurate final dimensions for the premolar model. The surface morphology of the green body and the sintered premolars that are produced using the two methods is then determined using scanning electronic microscopy. The sintered premolars are seated on a stone model to determine the marginal gap using an optical microscope. The hardness and the flexural strength are also measured for the purpose of comparison.

The developed solvent-free slurry for 3DSP can be used to produce a premolar green body without micro-cracks or delamination. The maximal marginal gap for the sintered premolar parts that are constructed using the green bodies from dental CAM is 98.9 µm and that from 3DSP is 72 µm. Both methods produce a highly dense zirconia premolar using the same sintering conditions. The hardness value for the dental CAM group is 1238.8 HV, which is slightly higher than that for the 3DSP group (1189.4 HV) because there is a difference in the pre-processing of the initial ceramic materials. However, the flexural strength for 3DSP is 716.76 MPa, which is less than the requirement for clinical use.

This study verifies that 3DSP can be used to fabricate a zirconia dental restoration device that is as good as the one that is produced using the dental CAM system and which has a marginal gap that is smaller than the threshold value. The resulting premolar restoration devices that are produced by sintering the green bodies that are produced using 3DSP and dental CAM under the same conditions have a similar hardness value, which is four times greater than that of enamel. The flexural strength of 3DSP does not meet the requirement for clinical use.

Three-dimensional (3D) printing technologies have gained attention in dentistry because of their ability to print objects with complex geometries with high precision and accuracy, as well as the benefits of saving materials and treatment time. This study aims to explain the principles of the main 3D printing technologies used for manufacturing dental prostheses and devices, with details of their manufacturing processes and characteristics. This review presents an overview of available 3D printing technologies and materials for dental prostheses and devices.

This review was targeted to include publications pertaining to the fabrication of dental prostheses and devices by 3D printing technologies between 2012 and 2021. A literature search was carried out using the Web of Science, PubMed, Google Scholar search engines, as well as the use of a manual search.

3D printing technologies have been used for manufacturing dental prostheses and devices using a wide range of materials, including polymers, metals and ceramics. 3D printing technologies have demonstrated promising experimental outcomes for the fabrication of dental prostheses and devices. However, further developments in the materials for fixed dental prostheses are required.

3D printing technologies are effective and commercially available for the manufacturing of polymeric and metallic dental prostheses. Although the printing of dental ceramics and composites for dental prostheses is promising, further improvements are required.

The low-temperature sintering of silica glass combined with additive manufacturing (AM) technology has brought a revolutionary change in glass manufacturing. This study aims to carry out in an attempt to achieve precious manufacturing of silicate glassy matrix through the method of slurry extrusion.

A low-cost slurry extrusion modelling technology is used to extrude silicate glassy matrix inks, composed of silicate glass powder with different amounts of additives. Extrudability of the inks, their printability window and the featuring curves of silicate glassy matrix are investigated. In addition, the properties of the low-temperature sintering green part as a functional part are explored and evaluated from morphology, hardness and colour.

The results showed that the particle size was mainly distributed from 1.4 µm to 5.3 µm, showing better slurry stability and print continuity. The parameters were set to 8 mm/s, 80% and 0.4 mm, respectively, to achieve better forming of three-dimensional (3D) samples. Besides, the organic binder removal step was concentrated on 200°C–300°C and 590°C–650°C was the fusion bonding temperature of the powder. The hardness values of 10 test samples ranged from 588 HL to 613 HL, which met the requirements of hard stones with super-strong mechanical strength. In addition, the mutual penetration of elements caused by temperature changes may lead to a colourful appearance.

The custom continuous AM technology enables the fabrication of a glass matrix with 3D structural features. The precise positioning technology of the glass matrix is expected to be applied more widely in functional parts.

Aluminium is being increasingly used in refinery construction. Applications range from storage tanks to moisture‐proofing pipe insulation; from heat exchangers to structural elements. The main reasons for this are its good resistance to many types of corrosion, low weight, low cost per unit volume, high thermal conductivity, non‐magnetic and non‐sparking characteristics, good reflectivity and good appearance. From the design engineer's point of view, the metal has the further advantages of good workability and high strength in its alloys. The author describes some of the current practices and experiences in the U.S.A.