Search results

This study aims to clarify the mechanism of film hole location at the span-wise direction of an internal cooling channel with crescent ribs on the adiabatic film cooling performance, three configurations are designed to observe the effects of the distance between the center of the ellipse and the side wall(Case 1, l = w/2, Case 2, l = w/3 and for Case 3, l = w/4).

Numerical simulations are conducted under two blowing ratios (i.e. 0.5 and 1) and a fixed cross-flow Reynolds number (Re_c = 100,000) with a verified turbulence model.

It is shown that at low blowing ratio, reducing the distance increases the film cooling effectiveness but keeps the trend of the effectiveness unchanged, while at high blowing ratio, the characteristic is a little bit different in the range of 0 = x/D = 10.

These features could be explained by the fact that shrinking the distance between the hole and side wall induces a much smaller reserved region and vortex downstream the ribs and a lower resistance for cooling air entering the film hole. Furthermore, the spiral flow inside the hole is impaired.

As a result, the kidney-shaped vortices originating from the jet flow are weakened, and the target surface can be well covered, resulting in an enhancement of the adiabatic film cooling performance.

This paper aims to comprehensively clarify the research status of thermal transport of supercritical aviation kerosene, with particular interests in the effect of cracking on heat transfer.

A brief review of current research on supercritical aviation kerosene is presented in views of the surrogate model of hydrocarbon fuels, chemical cracking mechanism of hydrocarbon fuels, thermo-physical properties of hydrocarbon fuels, turbulence models, flow characteristics and thermal performances, which indicates that more efforts need to be directed into these topics. Therefore, supercritical thermal transport of n-decane is then computationally investigated in the condition of thermal pyrolysis, while the ASPEN HYSYS gives the properties of n-decane and pyrolysis products. In addition, the one-step chemical cracking mechanism and SST k-ω turbulence model are applied with relatively high precision.

The existing surrogate models of aviation kerosene are limited to a specific scope of application and their thermo-physical properties deviate from the experimental data. The turbulence models used to implement numerical simulation should be studied to further improve the prediction accuracy. The thermal-induced acceleration is driven by the drastic density change, which is caused by the production of small molecules. The wall temperature of the combustion chamber can be effectively reduced by this behavior, i.e. the phenomenon of heat transfer deterioration can be attenuated or suppressed by thermal pyrolysis.

The issues in numerical studies of supercritical aviation kerosene are clearly revealed, and the conjugation mechanism between thermal pyrolysis and convective heat transfer is initially presented.

The purpose of this paper is to augment heat transfer rates of traditional rib-elements with minimal pressure drop penalties.

The novel geometries in the present research are conventional cylindrical ribs with rounded transitions to the adjacent flat surfaces and with modifications at their bases. All turbulent fluid flow and heat transfer results are presented using computation fluid dynamics with a validated v2f turbulence closure model. Turbulent flow characteristics and heat transfer performances in square channels with improved ribbed structures are numerically analyzed in this research work.

Based on the results, it is found that rounded transition cylindrical ribs have a large advantage over the conventional ribs in both enhancing heat transfer and reducing pressure loss penalty. In addition, cylindrical ribs increase the flow impingement at the upstream of the ribs, which will effectively increase the high heat transfer areas. The design of rounded transition cylindrical ribs and grooves will be an effective way to improve heat transfer enhancement and overall thermal performance of internal channels within blade cooling.

The novel geometries in this research are conventional cylindrical ribs with rounded transitions to the adjacent flat surfaces and with modifications at their bases. The combination of cylindrical ribs and grooves to manipulate the turbulent flow.

In this study, numerical simulations are performed to compare the adiabatic film cooling effectiveness and reveal the difference of film cooling mechanisms of two models with the same geometries and cross-section areas of film holes’ exits at three typical blowing ratios (M = 0.5, 1 and 1.5). The two models are an elliptical model and a cylindrical model with 90° compound angle, respectively.

Three different cases are considered in this work and the baseline is the model with a cylindrical film hole. The same boundary conditions and a validated turbulence model (realizable k-ε) are adopted for all cases.

The results show that both the elliptical and cylindrical models with 90° compound angle can enhance the film cooling effectiveness compared with the baseline. However, the elliptical model performs well at lower blowing ratios and in the near region at each blowing ratio because of the wider width of the film hole’s exit. The cylindrical model with 90° compound angle provides better film cooling effectiveness in the further downstream area of the film hole at higher blowing ratio because of the less lift-off and better coolant coverage in the larger x/D region along the mainstream direction.

Overall, it can be concluded that although the elliptical and cylindrical models with 90° compound angle have identical hole exits, the different inlet direction and cross-sectional geometry affect the flow structures when the coolant enters, moves through and exits the hole and finally different film cooling results appear.

The purpose of this paper is to develop a coupled lattice Boltzmann model for the simulation of the freezing process in unsaturated porous media.

In the developed model, the porous structure with complexity and disorder was generated by using a stochastic growth method, and then the Shan-Chen multiphase model and enthalpy-based phase change model were coupled by introducing a freezing interface force to describe the variation of phase interface. The pore size of porous media in freezing process was considered as an influential factor to phase transition temperature, and the variation of the interfacial force formed with phase change on the interface was described.

The larger porosity (0.2 and 0.8) will enlarge the unfrozen area from 42 mm to 70 mm, and the rest space of porous medium was occupied by the solid particles. The larger specific surface area (0.168 and 0.315) has a more fluctuated volume fraction distribution.

The concept of interfacial force was first introduced in the solid–liquid phase transition to describe the freezing process of frozen soil, enabling the formulation of a distribution equation based on enthalpy to depict the changes in the water film. The increased interfacial force serves to diminish ice formation and effectively absorb air during the freezing process. A greater surface area enhances the ability to counteract liquid migration.

The purpose of this paper is to investigate the unsteady flow past through a permeable diamond-shaped cylinder and to study the effects of the aspect ratios and Darcy numbers of the cylinder.

The lattice Boltzmann method with D2Q9 lattice model was used to simulate the unsteady flow through permeable diamond-shaped cylinders. The present numerical method is validated against the available data.

The key findings are that increasing the permeability enhances the suppression of vortex shedding, and that the Strouhal number is directly proportion to the Darcy number, Reynolds number and the aspect ratio of the porous cylinder.

The present study considers unsteady laminar flow past through single permeable diamond-shaped cylinder. According to the authors’ knowledge, very few studies have been found in this field. The present findings are novel and original, which in turn can attract wide attention and citations.

The purpose of this paper is to numerically study the influence of wall conduction on the heat transfer of supercritical n-decane in the active regenerative cooling channels.

A horizontally placed rectangular pipe with a solid zone and another one without a solid zone were used. A drastic variation of thermo-physical properties was emphatically addressed. After the verification of mesh and turbulence models comparing with the experimental results, a mesh number of 4.5 M and the low Reynolds number SST k-ω turbulence model were chosen. The solution of the governing equations and the acquisition of the numerical results were executed by the commercial software FLUENT 2020 R1.

The numerical results indicate that there is a heat transfer deterioration (HTD) potential for the upper wall, lower wall and sidewall with the decrease of mass flux. Due to wall conduction, the distribution of the fluid temperature at spanwise-normal planes becomes uniform and this feature also takes advantage of the relatively uniform transverse velocity. For the streamwise-normal planes, the low fluid temperature appears close to the upper wall at the region near the sidewall and vice versa for the region near the centre. Undoubtedly, the secondary flow at the cross-section plays a crucial role in this process and the relatively cool mainstream is affected by the vortices.

This study warns that the wall conduction must be considered in the practical design and thermal optimization due to the sensibility of thermo-physical properties to the heat flux. The secondary flow caused by the buoyancy force (gravity) plays a significant role in the supercritical heat transfer and mixed convection heat transfer should be further studied.

The discontinuous Galerkin finite element method (DGFEM) is very suited for realizing high order resolution approximations on unstructured grids for calculating the hyperbolic conservation law. However, it requires a significant amount of computing resources. Therefore, this paper aims to investigate how to solve the Euler equations in parallel systems and improve the parallel performance.

Discontinuous Galerkin discretization is used for the compressible inviscid Euler equations. The multi-level domain decomposition strategy was used to deal with the computational grids and ensure the calculation load balancing. The total variation diminishing (TVD) Runge–Kutta (RK) scheme coupled with the multigrid strategy was employed to further improve parallel efficiency. Moreover, the Newton Block Gauss–Seidel (GS) method was adopted to accelerate convergence and improve the iteration efficiency.

Numerical experiments were implemented for the compressible inviscid flow problems around NACA0012 airfoil, over M6 wing and DLR-F6 configuration. The parallel acceleration is near to a linear convergence. The results indicate that the present parallel algorithm can reduce computational time significantly and allocate memory reasonably, which has high parallel efficiency and speedup, and it is well-suited to large-scale scientific computational problems on multiple instruction stream multiple data stream model.

The parallel DGFEM coupled with TVD RK and the Newton Block GS methods was presented for hyperbolic conservation law on unstructured meshes.

With the development of electronic devices, including the desires of integration, miniaturization, high performance and the output power, cooling requirement of chips have been increased gradually. Water-cooled minichannel is an effective cooling technology for cooling of heat sinks. The minichannel flow geometry offers large surface area for heat transfer and a high convective heat transfer coefficient with only a moderate pressure loss. The purpose of this paper is to analyze a minichannel heat sink having the bottom size of 35 mm×35 mm numerically. Two kinds of chip arrangement are investigated: diagonal arrangement and parallel arrangement.

Computational fluid dynamics (CFD) technique is used to investigate the flow and thermal fields in forced convection in a three-dimensional minichannels heat sink with different chip arrangements. The standard k-e turbulence model is applied for the turbulence simulations on the minichannel heat sink.

The results show that the bottom surface of the heat sink with various chip arrangements will have different temperature distribution and thermal resistance. A suitable chip arrangement will achieve a good cooling performance for electronic devices.

The fluid is incompressible and the thermophysical properties are constant.

New and additional data will be helpful as guidelines in the design of heat sinks to achieve a good thermal performance and a long lifetime in operation.

In real engineering situations, chips are always placed in various manners according to design conditions and constraints. In this case the assumption of uniform heat flux is acceptable for the surfaces of the chips rather than for the entire bottom surface of the heat sink.

The employment of continuous ribs in a passage involves a noticeable pressure drop penalty, while other studies have shown that truncated ribs may provide a potential to reduce the pressure drop while keeping a significant heat transfer enhancement. The purpose of this paper is to perform computer-aided simulations of turbulent flow and heat transfer of a rectangular cooling passage with continuous or truncated 45-deg V-shaped ribs on opposite walls.

Computational fluid dynamics technique is used to study the fluid flow and heat transfer characteristics in a three-dimensional rectangular passage with continuous and truncated V-shaped ribs.

The inlet Reynolds number, based on the hydraulic diameter, is ranged from 12,000 to 60,000 and a low-Re k-e model is selected for the turbulent computations. The local flow structure and heat transfer in the internal cooling passages are presented and the thermal performances of the ribbed passages are compared. It is found that the passage with truncated V-shaped ribs on opposite walls provides nearly equivalent heat transfer enhancement with a lower (about 17 percent at high Reynolds number of 60,000) pressure loss compared to a passage with continuous V-shaped ribs or continuous transversal ribs.

The fluid is incompressible with constant thermophysical properties and the flow is steady. The passage is stationary.

New and additional data will be helpful in the design of ribbed passages to achieve a good thermal performance.

The results imply that truncated V-shaped ribs are very effective in improving the thermal performance and thus are suggested to be applied in gas turbine blade internal cooling, especially at high velocity or Reynolds number.