Search results

In friction welding of dissimilar joint method, few material compositions are not possible to weld effectively. For better dissimilar metal joining in friction welding, the interlayer techniques are used by the third metal to increase the diffusion for suitable metal bonding. The interlayer metals are popularly held by coating, foils, sheet and solid rod form. The coating method needs more care for surface preparation with special coating equipment with high workmanship. In case of foil as intermediate metal, more care is neededfor holding between the metal; most of the time this technique has the possibility of failure by peeling off from the contact surface during high speed rotation with pressure during friction generation.

In this investigation, a copper coin was machined to a suitable size (transition fit) to suit the recess inside the SS rod. The mating surfaces of Cu coin, SS rod and Ti alloy were machined, polished to mirror finish and handled in friction welding machine. The purpose of the transition fit between the coin and SS rod is for holding the same intact before the beginning of the process.

Successful joint was achieved with good joint strength at less time. Empirical models were established to fin out the joint strength at any given parameter within the range of investigation

The models developed can be used only within the range of investigation considered for experimentation.

The paper includes implications for the development of a method of joining any dissimilar joints

In this investigation, a copper coin was machined to a suitable size (transition fit) to suit the recess inside the SS rod. The mating surfaces of Cu coin, SS rod and Ti alloy were machined, polished to mirror finish and handled in friction welding machine. The purpose of the transition fit between the coin and SS rod is for holding the same intact before the beginning of the process.

Joining, while first and foremost a pragmatic undertaking, concerned more with needs and results than with theory, will likely have to change with the dawn of the twenty‐first century to a true science. As materials become ever‐more sophisticated in their chemical composition, molecular morphology, micro‐ and nano‐structure, and macro‐structural arrangement to provide ever‐better functionally specific properties, a more complete and precise understanding of how such materials can be joined for optimal effectiveness and efficiency will become essential. Traditional options for joining will surely evolve – sometimes to provide unimagined capabilities. But, in addition, totally new methods will almost certainly emerge as evolution of materials gives way to revolution to meet unimagined new designs and design demands. This paper takes a glance at the past and a hard look at the present in the hope of catching a glimpse of the future.

The purpose of this paper is to point out the possibilities for friction welding of dissimilar steels which are used in various industries. In addition, friction welding is a welding method that is applied for executing the very responsible joints. This research is focused on friction and tribological processes in the friction plane of the two pieces during the welding.

The present study research has been conducted based on the experimental testing of cylindrical specimens and results are analyzed.

The austenite grain size is affected by several factors through the friction process phase and the compacting phase during the welding. The very fine grain is the consequence of the high degree of the plastic deformation of the near-the-contact layers even in the friction phase. The viscous layer, which is formed during the stable friction phase, is the area where the moving of matter occurs according to a very complex mechanism.

The paper contains useful results from the area of conventional friction welding of dissimilar steels and it can be very useful to researchers and engineers who deal with similar problems.

The purpose of this paper is to join AA5052 to AISI 1006 steel sheets using the spot friction forming technique.

A steel sheet was pre-holed with a diameter of 4.8 mm and pre-threaded with a single internal M6 thread. Lap joint configuration was used so that the aluminium specimen was put over steel. A rotating tool with a 10 mm diameter was used for the joining process. A Taguchi method was used to design three process parameters (plunging tool depth, rotating speed and preheating time), with three levels for each parameter. The effect of the process parameters on the joint shear strength was analysed. The macrostructure, microstructure and scanning electron microscope of the joint were investigated. The temperature distribution during the joining process was recorded.

The formed aluminium was extruded through the steel hole and penetrated through the thread slot. A mechanical interlock was achieved between the extruded aluminium and the steel. The plunging depth of the tool exhibited a significant effect on the joint shear strength. The joint efficiency increased gradually as the plunging depth increased. Two modes of failure were found shear and pull-out. The maximum temperature during the process reached 50 per cent of aluminium’s melting point.

For the first time, AA5052 was joined with AISI 1006 steel using a friction spot forming technique with an excellent joint efficiency.

The purpose of this paper is to compile a comprehensive status report on pipes/piping networks across different industrial sectors, along with specifications of materials and sizes, and showcase welding avenues. It further extends to highlight the promising friction stir welding as a single solid-state pipe welding procedure. This paper will enable all piping, welding and friction stir welding stakeholders to identify scope for their engagement in a single window.

The paper is a review paper, and it is mainly structured around sections on materials, sizes and standards for pipes in different sectors and the current welding practice for joining pipe and pipe connections; on the process and principle of friction stir welding (FSW) for pipes; identification of main welding process parameters for the FSW of pipes; effects of process parameters; and a well-carved-out concluding summary.

A well-carved-out concluding summary of extracts from thoroughly studied research is presented in a structured way in which the avenues for the engagement of FSW are identified.

The implications of the research are far-reaching. The FSW is currently expanding very fast in the welding of flat surfaces and has evolved into a vast number of variants because of its advantages and versatility. The application of FSW is coming up late but catching up fast, and as a late starter, the outcomes of such a review paper may support stake holders to expand the application of this process from pipe welding to pipe manufacturing, cladding and other high-end applications. Because the process is inherently inclined towards automation, its throughput rate is high and it does not need any consumables, the ultimate benefit can be passed on to the industry in terms of financial gains.

To the best of the authors’ knowledge, this is the only review exclusively for the friction stir welding of pipes with a well-organized piping specification detailed about industrial sectors. The current pipe welding practice in each sector has been presented, and the avenues for engaging FSW have been highlighted. The FSW pipe process parameters are characteristically distinguished from the conventional FSW, and the effects of the process parameters have been presented. The summary is concise yet comprehensive and organized in a structured manner.

The purpose of this paper is to investigate the impact of ultrasonic vibration (UV) and tool pin profile on mechanical properties and microstructural behaviour of AA7075-T651 and AA6061-T6 joints was analysed.

The joints were fabricated using three different tool pin profiles such as cylindrical, square and triangle. For each tool pin profile, two different UV powers of 1.5 kW and 2 kW were used.

On both the advancing and retreating sides of the weld, the thermo-mechanically affected zone has the lowest microhardness. In all joints, the tensile fracture locations match to the minimum hardness values. Field emission scanning electron microscope fractography of tensile tested specimens reveals heterogeneous modes of brittle, shear and ductile fracture. Three-point bending analysis was performed to determine the ductility and soundness of the weld joint. The acoustic softening effect of UV, as well as the static and dynamic ratio of tool pin profile, plays an important role in determining the material flow and mechanical behaviour of the joint.

Dissimilar aluminium joining fascinates many applications like aircraft, aerospace, automobiles, ship building and electronics, where fusion welding is a very intricate process because of the deviation in its physical and chemical properties.

From this study investigation, it is found that the square pin profiled tool with 2 kW UV power produces metallurgical defect-free and mechanically sound weld with maximum tensile strength, hardness and bending load of 297 MPa, 151HV and 3.82 kN, respectively.

The purpose of this paper is to join an anodized aluminium alloy AA6061 sheet with high-density polyethylene (HDPE) using friction spot process.

The surface of AA6061 sheet was anodized to increase the pores’ size. A lap joint configuration was used to join the AA6061 with HDPE sheets by the friction spot process. The joining process was carried out using a rotating tool of different diameters: 14, 16 and 18 mm. Three tool-plunging depths were used – 0.1, 0.2 and 0.3 mm – with three values of the processing time – 20, 30 and 40 s. The joining process parameters were designed according to the Taguchi approach. Two sets of samples were joined: the as-received AA6061/HDPE and the anodized AA6061/HDPE.

Frictional heat melted the HDPE layers near the lap joint line and penetrated it through the surface pores of the AA6061 sheet via the applied pressure of the tool. The tool diameter exhibited higher effect on the joint strength than processing time and the tool-plunging depth. Specimens of highest and lowest tensile force were failed by necking the polymer side and shearing the polymer layers at the lap joint, respectively. Molten HDPE was mechanically interlocked into the pores of the anodized surface of AA6061 with an interface line of 18-m width.

For the first time, HDPE was joined with the anodized AA6061 by the friction spot process. The joint strength reached an ideal efficiency of 100 per cent.

Recently, several studies have been performed on lap welding of aluminum and copper using friction stir welding (FSW). The formation of intermetallic compounds at the weld interface hampers the weld quality. The use of an intermediate layer of a compatible material during welding reduces the formation of intermetallic compounds. The purpose of this paper is to optimize the FSW process parameters for AA6063-ETP copper weld, using a compatible zinc intermediate filler metal.

In the present study, a three-level, three-factor central composite design (CCD) has been used to determine the effect of various process parameters, namely, tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil on ultimate tensile strength of the weld. A total of 60 experimental data were fitted in the CCD. The experiments were performed with tool rotational speeds of 1,000, 1,200 and 1,400 rpm each of them with tool traverse speeds of 5, 10 and 15 mm/min. A zinc inter-filler foil of 0.2 and 0.4 mm was also used. The macrograph of the weld surface under different process parameters and the tensile strength of the weld have been investigated.

The feasibility of joining 3 mm thick AA6063-ETP copper using zinc inter-filler is established. The regression analysis showed a good fit of the experimental data to the second-order polynomial model with a coefficient of determination (R²) value of 0.9759 and model F-value of 240.33. A good agreement between the prediction model and experimental findings validates the reliability of the developed model. The tool rotational speed, tool traverse speed and thickness of inter-filler zinc foil significantly affected the tensile strength of the weld. The optimal conditions found for the weld were, rotational speed of 1,212.83 rpm and traverse speed of 9.63 mm/min and zinc foil thickness is 0.157 mm; by using optimized values, ultimate tensile strength of 122.87 MPa was achieved, from the desirability function.

Aluminium and copper sheets could be joined feasibly using a zinc inter-filler. The maximum tensile strength of joints formed by inter-filler (122.87 MPa) was significantly better as compared to those without using inter-filler (83.78 MPa). The optimum process parameters to achieve maximum tensile strength were found by CCD.

The purpose of this paper is to join sheets of an aluminium alloy together with pre-holed carbon steel via friction spot technique.

An AISI 1006 steel sheet was a pre-holed with a 4.8 mm diameter and put under AA5052 sheet with a lap joint configuration. The joining process was carried out by extruding the aluminium through the steel hole using a rotating tool of 10 mm diameter. Furthermore, three process parameters (pre-heating time, rotating speed and plunging depth of the tool) with three values for each parameter were used to study their effects on the joints quality. In order to join samples, nine experiments were designed according to a Taguchi method. Shear strength, microstructure and X-ray diffraction tests of the joint were carried out.

The joining mechanism occurred by a mechanical interlock of the extruded aluminium with the inner surface of the steel hole. The tool plunging depth had a significant effect on the shear strength of the joint. The shear strength of two joints exceeded the shear strength of the wrought material (AA5052). All samples failed with two modes: pull-out and shearing of the extruded aluminium.

For the first time, the extrusion technique was used to join AA5052 sheet together with pre-holed carbon steel, with a perfect joint efficiency.