Search results

Use of packed beds, enhanced tubes, nano-fluids and artificial ribs are few passive techniques to increase heat transfer in solar air heaters (SAHs). Artificial ribs attached to the absorber plate of the SAH will enhance the turbulence near the plate. Experimental analyses are conducted to find the thermal performance of SAH with ribs of regular geometries including rectangular, semi-circular and triangular in cross section. This paper aims to present the improvement in thermal performance of SAH with modified-arc.

Absorber plates are designed with ribs of rectangular, triangular, semi-circular and modified-arc in cross-section using existing data in literature. Physical dimensions of the ribs are designed by adapting procedure from literature. Absorber plates are manufactured with ribs and coated with blackboard paint and fixed to the existing SAH. Experiments are conducted with a variable-speed blower fixed to the inlet section of the SAH, which is used to supply air at different mass flow rates in a range between 0.495 and 0.557 kg/min.

Efficiency is found to be a strong function of mass flow rate of air through the SAH from the present experimental investigations. It was found that use of modified-arc ribs enhanced the efficiency of SAH by 105.35 per cent compared to SAH with plane absorber plate. Efficiency of SAH with modified-arc ribs is found to be higher by 24.43, 45.61 and 63.21 per cent, respectively, for SAH with semi-circular, rectangular and triangular arc ribs on its absorber plate.

Experiments on SAH are conducted during daytime from 9:00 am to 5:00 pm in open atmospheric conditions. Solar intensity is continuously changing during the experimentation from morning to evening. Calculations are made based on the observations with average values of solar intensity and temperature readings. More accurate values of SAH efficiency can be obtained with constant heat supply to the absorber plate by simulating the experimental setup in indoor conditions. Temperature and flow rate observations could be more accurate with sophisticated instrumentation rather than using simple thermocouples and orifice meters.

SAHs are basically used to supply hot air for both rural and industrial applications. These are used for crop drying, preheating of air, removal of moisture from leather, chemicals, etc. Conventionally, formers in India are using open sun drying to remove moisture from agricultural products. In this method, the moisture can be removed up to a level of 20 to 25 per cent. Use of SAH can remove moisture up to below 5 per cent and process is clean without reducing the quality of agricultural products. Enhancing the efficiency of SAHs will surely increase its usage by formers for crop drying.

Use of artificial ribs on absorber plate of SAH is most economical among many of the active and passive techniques. Numerical and experimental investigations are found in literature with regular cross-sectional ribs, including rectangular, triangular and semi-circular. The present work proposed new shape of the ribs named as modified-arc, which was not presented in the literature. Experimental analysis proved that the use of modified-arc makes the SAH more efficient in heat transfer.

Solar energy applications are limited because of its intermittent and discontinuous availability with respect to time. Hence, solar energy thermal conversion systems need integration with thermal storage units (TSUs) to use solar energy in off sunshine hours. This paper aims to perform thermal analysis of a solar air heater (SAH) integrated with a phase change material (PCM)-based TSU to supply hot air during night period.

An experimental setup with TSU as main component was prepared with SAH at its upward side, food chamber at its downward side as subcomponents. In TSU, paraffin wax was used as thermal energy storage material. Mass flow rate of air considered as an input parameter in the experiment. Two different absorber plates, namely, plane and ribbed absorber plates were used for the experimentation. Each day for a fixed mass flow of air, observations were made during charging and discharging of PCM.

Nusselt number and convection heat transfer coefficients were analytically calculated by considering flow through TSU as external flow over bank of tubes in a rectangular duct. A temperature drop of around 7-8°C during charging of PCM and temperature rise of around 4-5°C during discharging of PCM was observed from the experimental results. The average practical efficiency of TSU with ribbed absorber plate SAH during charging and discharging of PCM was 22 and 6 per cent, respectively, higher than that of TSU with plane absorber plate SAH.

There are no limitations for research on SAH integrated with TSU. Different PCM including paraffin wax, Glauber’s salt, salt hydrates and water are used for thermal storage. Only limitation is lower efficiency of SAH integrated with TSU because of lower heat transfer coefficients with air as working medium. If it can improve heat transfer coefficients of air then heat transfer rates with these units will be higher.

There are no practical limitations for research on SAH integrated with TSU. Sophisticated instrumentation is needed to measure flow rates, temperatures and pressure variations of air.

In poultry farms during night, chicks cannot survive at cold climatic conditions. Hence, hot air should be supplied to poultry farms whenever the atmospheric temperature drops. It is proposed that, in combination with TSUs, heat produced by SAH is stored in day time in the form of either sensible or latent heat and is retrieved to provide hot air in the night times. This will reduce total operating costs in poultry farms.

Conventionally, people are producing hot air by combusting coal in poultry forms. This cost around Rs. 75,000 per month for a batch of 225 to 250 chicks in a poultry form. Hot air could be produced economically during off sunshine hours from SAH integrated with TSU compared to the conventional method of coal burning. Present experimental investigations conducted to fill the literature gap in this area of research and to design a SAH integrated with TSU to produce hot air for poultry forms.

Present investigation conducts a study on the hydrothermal features of a double flow Parabolic Trough Solar Collector (PTSC) equipped with sinusoidal-wavy grooved absorber tube and twisted tape insert filled with nanofluid. This paper aims to present an effectual PTSC which is comprised by nanofluid numerically by means of finite volume method.

The beneficial results such as pressure drop inside the absorber tube, mean predicted friction factor, predicted average Nusselt number and hydrothermal Performance Evaluation Criteria (PEC) are evaluated and reported to present the influences of numerous factors on studied interest outcomes. Effects of different Reynolds numbers and environmental conditions are also determined in this investigation.

It is found that using the absorber roof (canopy) can enhance the heat transfer ratio of PTSCs significantly during all studied Reynolds numbers. Also, it is realized that the combination of inner grooved surface, outer corrugated surface and inserting turbulator can improve the thermal-hydraulic characteristics of PTSCs sharply.

Novel PTSC (N.PTSC) filling with two Heat Transfer Fluids (HTFs), inner and outer surface corrugated absorber tube, absorber roof and inserting twisted tape (N.PTSC.f) has the highest PEC values among all novel configurations along all investigated Reynolds numbers which is followed by configurations N.PTSC with two HTFs and inserting twisted tape (N.PTSC.e), N.PTSC with two HTFs and outer surface corrugated absorber tube (N.PTSC.b) and N.PTSC with two HTFs and inner surface corrugated absorber tube (N.PTSC.c), respectively. N.PTSC.f Nusselt number values can overcome the high values of friction factor, and therefore is introduced as the most efficient model in the current study.

The purpose of this paper is to describe the structure of nonlinear dampers and the dynamic equations, and nonlinear realization principles and optimize the parameters of nonlinear dampers. Using the finite element method to analyze the seismic performance of the frame structure with shock absorber.

The nonlinear shock absorber was installed in a six-storey reinforced concrete frame structure to study its seismic performance. The main structure was designed according to the eight degree seismic fortification intensity, and the time history dynamic analysis was carried out by Abaqus finite element software. EL-Centro, Taft and Wenchuan seismic record were selected to analyze the seismic response of the structure under different magnitudes and different acceleration peaks.

Through the principle study and parameter analysis of the nonlinear shock absorber, combined with the finite element simulation results, the shock absorption performance and shock absorption effect of the nonlinear energy sink (NES) nonlinear shock absorber are given as follows: first, the damping of the NES shock absorber is satisfied, and the linear spring stiffness and nonlinear stiffness of the shock absorber are based on the relationship k1=kn×kl2, so that the spring design length is fixed, and the linear stiffness of the shock absorber can be obtained. The nonlinear shock absorber has the characteristics of high rigidity and frequency bandwidth, so that the frequency is infinitely close to the frequency of the main structure, and when the mass of the shock absorber satisfies between 0.056 and 1, a good shock absorption effect can be obtained, and the reinforced concrete with the shock absorber is obtained. The frame structure can effectively reduce the seismic response, increase the natural vibration period of the structure and reduce the damage loss of the structure. Second, the spacer and each additional shock absorber have a small difference in shock absorption effect. After the shock absorber parameters are accurately calculated, the number of installations does not affect the shock absorption effect of the structure. Therefore, the shock absorber is properly constructed and accurately calculated. Parameters can reduce costs.

New shock absorbers reduce earthquake-induced damage to buildings.

The shock absorber is an important component of vehicle suspension that attenuates the vehicle vibration. Its running state directly affects the performance of the vehicle suspension. The purpose of this paper is to quantitatively study the relationship between damping characteristics and air chamber and oil properties in single-tube pneumatic shock absorber.

Combined with the principle of fluid dynamics and hydraulic transmission technology, the rebound stroke and compression stroke mathematical models, and damping characteristics simulation model are established to investigate the effect of the air chamber and oil property on damping characteristics.

Research results show that the initial pressure of the air chamber is the key parameter which influences the damping characteristics of the shock absorber. The change of the initial pressure has more impact on damping force, and less impact on the speed characteristic; the initial volume of the air chamber almost has no effect on the damping characteristics. The density and viscosity of the oil have certain influence on the damping characteristics. Therefore, selecting suitable damping oil is very important.

Using Matlab/Simulink software to build simulation models, its results are very accurate. The conclusions can provide a theoretical reference for the structure design of a single-tube pneumatic shock absorber.

A novel and simple six-band metamaterial absorber is proposed in the terahertz region, which is composed of an I-shaped absorber and circular ring with four gaps and a continuous metal ground plane separated by only 0.125 mm polyimide dielectric substrate. Initially, I-shaped resonator gives three bands at 0.4, 0.468 and 0.4928 THz with the absorptivity of 99.3%, 97.9% and 99.1%, respectively. The purpose of this paper is to improve the number of bands, for which the authors added the circular ring with four gaps, so the simulated metamaterial absorber exhibited six absorption peaks at 0.3392, 0.3528, 0.3968, 0.4676, 0.4768 and 0.492 THz, with the absorption rate of 91.4%, 94.2%, 94.9%, 90.3%, 77.5% and 97.4%, respectively. The surface current distribution and angle independence are explained for all the six frequencies which are used to analyze the absorption mechanism clearly. Structure maximum uses the squares and circles, so it will make the fabrication easy. The multiband absorbers obtained here have potential applications in many engineering technology, thermal radiation, material detection and imaging and optoelectronic areas.

This paper presents the design of the six-band metamaterial absorber which is from the I-shaped resonator and circular ring with four gaps and the metallic ground plane separated by the 0.125 polyimide dielectric substrate. The absorber exhibited six absorption peaks at 0.3392, 0.3528, 0.3968, 0.4676, 0.4768 and 0.492 THz, with the absorption rate of 91.4%, 94.2%, 94.9%, 90.3%, 77.5% and 97.4%, respectively. From the fabrication point of view, the proposed six-band metamaterial absorber has a very simple geometrical structure, and it is very easy to be fabricated.

The authors present a new and simple design of six-band absorber based on an I-shaped absorber and circular ring with four gaps and a metallic ground plane separated by a polyimide layer having the thickness of 0.125 mm. Six different resonance absorption peaks are found at 0.3392, 0.3528, 0.3968, 0.4676 , 0.4768 and 0.492 THz. Surface current distribution and angle independence plot have been studied to understand the absorption behavior of the designed terahertz metamaterial absorber.

The multiband absorbers obtained here have potential applications in many engineering technology, thermal radiation, material detection, security, sensors, imaging and optoelectronic areas.

Volumetric air receivers experience high thermal stress as a consequence of the intense radiation flux they are exposed to when used for heat and/or power generation. This study aims to propose a proper design that is required for the absorber and its holder to ensure efficient heat transfer between the fluid and solid phases and to avoid system failure due to thermal stress.

The design and modeling processes are applied to both the absorber and its holder. A multi-channel explicit geometry design and a discrete model is applied to the absorber to investigate the conjugate heat transfer and thermo-mechanical stress levels present in the steady-state condition. The discrete model is used to calibrate the initial state of the continuum model that is then used to investigate the transient operating states representing cloud-passing events.

The steady-state results constitute promising findings for operating the system at the desired airflow temperature of 700°C. In addition, we identified regions with high temperatures and high-stress values. Furthermore, the transient state model is capable of capturing the heat transfer and fluid dynamics phenomena, allowing the boundaries to be checked under normal operating conditions.

Thermal stress analysis of the absorber and the steady/transient-state thermal analysis of the absorber/holder were conducted. Steady-state heat transfer in the explicit model was used to calibrate the initial steady-state of the continuum model.

The purpose of this paper is to investigate the enhancement of the performance of bubble absorber using hybrid nanofluid as a cooled NH₃/H₂O absorption system to reduce their size and to find the best fitting model. A numerical model for ammonia-water bubble absorber was developed to show the influence of operating conditions and design parameters on the absorber performance.

A finite difference numerical method is used to solve the numerical model. The model is subjected to the inlet conditions of liquid, vapor and coolant flow regimes. The absorber modeling was divided into small elements along the absorber length.

The model proposed is validated with previously published works. Then agreement between the both is considered as good.

Numerical results/The use of hybrid nanofluids.

The results showed that the hybrid nanofluid is the best cooling medium. Very high heat transfer rates are obtained because of the high thermal conductivity and specific heat of hybrid nanofluid, and consequently, the absorber size decreases. It was also found that the absorber thermal load and the mass absorption flux increase with increasing of solid volume fraction. Also, the existence of an optimal absorber length was revealed, required for complete absorption when using hybrid nanofluid as a cooling medium. It is recommended that using hybrid nanofluid to remove the heat from the absorber is the best candidate for NH₃/H₂O absorption performance enhancement.

Limitations in traditional manufacturing methods currently employed in the production of acoustic devices, restricts the development of design led performance improvements. These devices are used to control sound energy and are commonly employed for tailoring room acoustics. solid freeform fabrication allows the production of acoustic structures more complex than traditionally manufactured devices. This paper aims to focus on a novel absorber based on destructive interference, considering performance, design and manufacture.

Selective laser sintering has been used in the investigation of the performance and manufacturing possibilities and limitations of a novel destructive interference absorber. Validation of the absorber performance is benchmarked against a conventional resonant absorber and compared to published results. The implications for acoustic devise design, the advances and limitations in manufacture using solid freeform fabrication techniques and potential applications are discussed.

An original absorber design has been shown to exhibit comparable acoustic absorption to that of a traditional solution. The nature of the geometry of the novel absorber demonstrates that the design flexibility afforded by solid freeform fabrication processes holds potential for applications incorporating new types of acoustic absorber. The use of solid freeform fabrication has demonstrated its potential to the application of acoustics, and has highlighted limitations due to post‐processing, material strength and the precision of the selectivity process.

Solid freeform fabrication techniques enable a new family of specifically engineered acoustic absorbers capable of incorporating performance benefits over conventional absorbers.

This paper focuses on room acoustic applications, the creation of high performance, conformal absorbers, applicable to a wide range of applications within the aerospace, automotive and construction industries, where space, weight and performance are key criteria.

This paper aims to design an active shock absorber scheme for use in conjunction with a passive shock absorber to suppress the horizontal vibration of elevator cars in a smaller range and shorter time. The developed active shock absorber will also improve the safety and comfort of passengers driving in ultra-high-speed elevators.

A six-degree of freedom dynamic model is established according to the position and condition of the car. Then the active shock absorber and disturbance compensation-based adaptive control scheme are designed and simulated in MATLAB/Simulink. The results are analysed and compared with the traditional shock absorber.

The results show that, compared with traditional spring-based passive damping systems, the designed active shock absorber can reduce vibration displacement by 60%, peak acceleration by 50% and oscillation time by 2/3 and is more robust to different spring stiffness, damping coefficient and load.

The developed active shock absorber and its control algorithm can significantly reduce vibration amplitude and converged time. It can also adjust the damping strength according to the actual load of the elevator car, which is more suitable for high-speed elevators.