Search results

This paper aims to investigate the preparation of AlN and Al₂O₃, as well as the effect of nano-AlN and nano-Al₂O₃, on friction and wear properties of copper-steel clad plate immersed in the lubricants.

Nano-AlN or nano-Al₂O₃ (0.1, 0.2, 0.3, 0.4 and 0.5 Wt.%) functional fluids were prepared. Their tribological properties were tested by an MRS-10A four-ball friction tester and a ball-on-plate configuration, and scanning electron microscope observed the worn surface of the plate.

An increase in nano-AlN and Al₂O₃ content enhances the extreme pressure and anti-wear performance of the lubricant. The best performance is achieved at 0.5 Wt.% of nano-AlN and 0.3 Wt.% of nano-Al₂O₃ with PB of 834 N and 883 N, a coefficient of friction (COF) of approximately 0.07 and 0.06, respectively. Furthermore, the inclusion of nano-AlN and nano-Al₂O₃ particles in the lubricant enhances its extreme pressure performance and reduces wear, leading to decreased wear spot depth. The lubricating effect of the nano-Al₂O₃ lubricant on the surface of the copper-steel composite plate is slightly superior to that of the nano-AlN lubricant, with a COF reaching 0.07. Both lubricants effectively fill and lubricate the holes on the surface of the copper-steel composite plate.

AlN and Al₂O₃ as water-based lubricants have excellent lubrication performance and can reduce the COF. It can provide some reference for the practical application of nano-water-based lubricants.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2023-0255/

The purpose of this study was the preparation of a poly(styrene-co-maleic anhydride)-g-polyetheramine (SMA-g-PEA) hyperdispersant that reduces the viscosity of the system and improves the colouring intensities of pigments.

PEA of specific quality was dissolved in propylene glycol methyl ether. SMA was then added according to the required mass ratio. The solution was refluxed for 10 h under a stream of protective N2. The prepared hyperdispersant was then characterised by Fourier-transform infrared, UV–visible and ¹H NMR spectroscopies, gel-permeation chromatography and thermogravimetry.

PEA was successfully grafted onto the SMA polymer and the synthesised product was found to be thermally stable. The copolymer with a 6:1 mass ratio is the best dispersant and was used to disperse carbon black, phthalocyanine blue and permanent violet in water-based systems, which helps to improve the application performance of each pigment by reducing the viscosity of the system and improving the colouring intensity of the pigment. The water dispersion is stable and does not exhibit an increase in viscosity after seven days of oven aging at 50°C.

SMA-g-PEA water-based hyperdispersants were successfully synthesised. The prepared hyperdispersants help to improve the application performance of each studied pigment by reducing the viscosity of the system and improving the colouring intensity of the pigment.

Polyurethane (PUR) foam parts are traditionally manufactured using metallic molds, an unsuitable approach for prototyping purposes. Thus, rapid tooling of disposable molds using fused filament fabrication (FFF) with polylactic acid (PLA) and glycol-modified polyethylene terephthalate (PETG) is proposed as an economical, simpler and faster solution compared to traditional metallic molds or three-dimensional (3D) printing with other difficult-to-print thermoplastics, which are prone to shrinkage and delamination (acrylonitrile butadiene styrene, polypropilene-PP) or high-cost due to both material and printing equipment expenses (PEEK, polyamides or polycarbonate-PC). The purpose of this study has been to evaluate the ease of release of PUR foam on these materials in combination with release agents to facilitate the mulding/demoulding process.

PETG, PLA and hardenable polylactic acid (PLA 3D870) have been evaluated as mold materials in combination with aqueous and solvent-based release agents within a full design of experiments by three consecutive molding/demolding cycles.

PLA 3D870 has shown the best demoldability. A mold expressly designed to manufacture a foam cushion has been printed and the prototyping has been successfully achieved. The demolding of the part has been easier using a solvent-based release agent, meanwhile the quality has been better when using a water-based one.

The combination of PLA 3D870 and FFF, along with solvent-free water-based release agents, presents a compelling low-cost and eco-friendly alternative to traditional metallic molds and other 3D printing thermoplastics. This innovative approach serves as a viable option for rapid tooling in PUR foam molding.

The purpose of this work was to study the effect of different wood surface preparations on the wetting and adhesion of coating.

In this research, six different chemical preparations to evaluate the photostability and properties of wood coating. Also, the effect of the same wood treatments on the properties of the coating, i.e. wetting, adhesion and the permeability of two types of coatings, was investigated.

As a result, benzoyl chloride and chromic acid were found to be the most effective photostabilizing preparations. Solvent-based polyurethane was more compatible with the prepared wood surfaces compared with water-based alkyd coatings.

Chemical modifications of wood surfaces affected the wetting of various coatings.

Various surface properties could be changed using preparation that affects important coating properties.

Unfortunately, the properties of transparent wood coatings used outdoors disappear through the early years of use, essentially due to the wood substrate’s photodegradation.

Wood is a widespread substrate because of its comfortable handling, availability, proper cost of preparation and its good mechanical strength because of its density. Architects and designers tend to use wood in the construction of green buildings. However, this material is disposed to weathering while using outdoors and it should be solved.

This study aims to examine the flow of unsteady mixed convective hybrid nanofluid over a rotating sphere with heat generation/absorption. The hybrid nanofluid contains different shapes of nanoparticles (copper [Cu] and aluminium oxide [Al₂O₃]) in the base fluid (water [H₂O]). The influence of different shapes (sphere, brick, cylinder, platelets and blades) of nanoparticle in water-based hybrid nanofluid is also investigated.

To analyse the nanomaterial, the flow model is established, and in doing so, the Prandtl’s boundary layer theory is incorporated into the present model. The bvp4c approach, i.e. finite difference method, is used to find the numerical solution of differential equations that is controlling the fluid flow. The effect of relevant flow parameters on nanofluid temperature and velocity profile is demonstrated in detailed explanations using graphs and bar charts, whereas numerical results for Nusselt number and the skin’s coefficient for various form parameters are presented in tabular form.

The rate of heat transfer is least for spherical-shaped nanoparticle because of its smoothness, symmetricity and isotropic behaviour. The rate of heat transfer is highest for blade-shaped nanoparticles as compared to other shapes (brick, cylindrical and platelet) of nanoparticles because the blade-shaped nanoparticles causes comparatively more turbulence flow in the nanofluid than other shapes of nanoparticle. Heat generation affects the temperature distribution and, hence, the particle deposition rate. The absorption of heat extracts heat and reduce the temperature across the rotating sphere. The heat generation/absorption parameter plays an important role in establishing and maintaining the temperature around the rotating sphere.

The numerical study is valid with the exception of the fluctuation in density that results in the buoyancy force and the functional axisymmetric nanofluid transport has constant thermophysical characteristics. In addition, this investigation is also constrained by the assumptions that there is no viscosity dissipation, no surface slippage and no chemically activated species. The hybrid nanofluid Al₂O₃–Cu/H₂O is an incompressible and diluted suspension. The single-phase hybrid nanofluid model is considered in which the relative velocity of water (H₂O) and hybrid nanoparticles (Al₂O₃–Cu) is the same and they are in a state of thermal equilibrium.

Study on convective flow across a revolving sphere has its applications found in electrolysis management, polymer deposition, medication transfer, cooling of spinning machinery segments, spin-stabilized missiles and other industrial and technical applications.

The originality of the study is to investigate the effect of shape factor on the flow of electrically conducting hybrid nanofluid past a rotating sphere with heat generation/absorption and magnetic field. The results are validated and provide extremely positive balance with the recognised articles. The results of the study provide many appealing applications that merit further study of the problem.

Whilst a modest number of investigations have been undertaken concerning nanofluids (NFs), the exploration of fluid flow under exponentially stretching velocities using NFs remains comparatively uncharted territory. This work presents a distinctive contribution through the comprehensive examination of heat and mass transfer phenomena in the NF ND–Cu/H₂O under the influence of an exponentially stretching velocity. Moreover, the investigation delves into the intriguing interplay of gyrotactic microorganisms and convective boundary conditions within the system.

Similarity transformations have been used on PDEs to convert them into dimensionless ODEs. The solution is derived by using the homotopy analysis method (HAM). The pictorial notations have been prepared for sundry flow parameters. Furthermore, some engineering quantities are calculated in terms of the density of motile microbes, Nusselt and Sherwood numbers and skin friction, which are presented in tabular form.

The mixed convection effect associated with the combined effect of the buoyancy ratio, bioconvection Rayleigh constant and the resistivity due to the magnetization property gives rise to attenuating the velocity distribution significantly in the case of hybrid nanoliquid. The parameters involved in the profile of motile microorganisms attenuate the profile significantly.

The current simulations have uncovered fascinating discoveries about how metallic NFs behave near a stretched surface. These insights give us valuable information about the characteristics of the boundary layer close to the surface under exponential stretching.

The novelty of the current investigation is the analysis of NF ND–Cu/H₂O along with an exponentially stretching velocity in a system with gyrotactic microorganisms. The investigation of fluid flow at an exponentially stretching velocity using NFs is still relatively unexplored.

Inclination angle has been reported to have an enhancing effect on the thermal-hydraulic characteristics and entropy of some thermal systems. Therefore, this paper aims to numerically investigate the effects of inclination angle, volume concentration and Reynolds number on the thermal and hydraulic characteristics and entropy generation rates of water-based Al₂O₃ nanofluids through a smooth circular aluminum pipe in a turbulent flow.

A constant heat flux of 2,000 Watts is applied to the circular surface of the tube. Reynolds number is varied between 4,000 and 20,000 for different volume concentrations of alumina nanoparticles of 0.5%, 1.0% and 2.0% for tube inclination angles of ±90o, ±60o, ±45o, ±30o and 0o, respectively. The simulation is performed in an ANSYS Fluent environment using the realizable kinetic energy–epsilon turbulent model.

Results show that +45o tube orientation possesses the largest thermal deviations of 0.006% for 0.5% and 1.0% vol. concentrations for Reynolds numbers 4,000 and 12,000. −45o gives a maximum pressure deviation of −0.06% for the same condition. The heat transfer coefficient and pressure drop give maximum deviations of −0.35% and −0.39%, respectively, for 2.0% vol. concentration for Reynolds number of 20,000 and angle ±90o. A 95%–99.8% and 95%–98% increase in the heat transfer and total entropy generation rates, respectively, is observed for 2.0% volume concentration as tube orientation changes from the horizontal position upward or downward.

Research investigating the effect of inclination angle on thermal-hydraulic performance and entropy generation rates in-tube turbulent flow of nanofluid is very scarce in the literature.

The purpose of this study is to examine the flow and heat transfer performance of titanium oxide/water and copper/water nanofluids with varying nanoparticle morphologies by considering magnetic, Joule heating and viscous dissipation effects. Furthermore, it studies the irreversibility caused by the flow of a hydromagnetic nanofluid past a radiated stretching sheet by considering different shapes of TiO₂ and Cu nanoparticles with water as the base fluid.

In this study, the authors investigated entropy production in an unsteady two-dimensional magneto-hydrodynamic nanofluid regime using water as the base fluid and five unique TiO₂ and Cu nanoparticle morphologies. Using appropriate similarity transformations, the controlling nonlinear system of partial differential equations is transformed into a system of ordinary differential equations. The shooting technique with Runge–Kutta method was then used to solve these equations quantitatively. The findings of this study are depicted graphically, and the skin friction corresponding to various nanoparticle geometries and physical parameter variations is tabulated.

To assess the reliability of the current findings, a tabular representation of the data was compared to that of previously published studies. It is noted that a reduction in thermal energy was detected as a result of the higher levels of Prandtl number (Pr). It is further analysed that the highest heat energy generation of TiO₂ nanoparticles was larger than that of Cu nanoparticles. The most important finding was that the sphere-shaped Cu/H₂O nanofluid had the lowest velocity and greatest temperature. Also, Cu nanoparticles in the shape of platelets generate the most entropy, while TiO₂ nanoparticles in the shape of spheres generate the least.

To the best of the knowledge of the authors, the attempt to investigate the previously unexplored shape effects of TiO₂ and Cu nanoparticles on the heat transfer enhancement and inherent irreversibility caused by hydromagnetic nanofluid flow past a radiated stretching sheet with magnetic, Joule heating and viscous dissipation effects. This study fills this gap in the existing literature and encourages scientists, engineers and businesses to do more research in this area. This model can be used to improve heat transfer in systems that use renewable energy, thermal management in industry and the processing of materials.

This paper aims to present the steady dual solutions on three-dimensional flow and heat transfer of nanofluid over a permeable non-linearly shrinking surface with two-order velocity slips conditions. Boundary layer assumption is considered in the mathematical modelling. Authors comprehend from previous studies and papers that the shrinking surfaces are extremely important in current engineering and environmental systems.

Using appropriate similarity variables, the full partial differential equations (PDF) are modified into a specific set of ordinary (similar) differential equations (ODE). The resulting non-linear ordinary differential system is then solved both analytically for some particular cases and numerically for the general case using the function bvp4c from MATLAB for characteristic values of the parameters which govern the equations. The transformed mathematical model is analysed using the bvp4c procedure. Based on the given assumptions, this study is able to produce multiple solutions of the problem.

The ordinary (similarity) differential equations have two branches solutions, upper and lower branch solutions, given some interval of shrinking and velocity slip parameters. The authors consider here a temporal stability analysis, as they want to establish which of the solutions are stable and which are not. In a distinct paragraph, the authors discuss in detail and present in a graphical manner the effects of shrinking and second-order slip flow model on the skin friction coefficient, surface wall heat flux and dimensionless velocity and temperature profiles. The analysis reveals that the second order slip has a big influence on the flow and heat transfer characteristics.

The present discoveries are unique and truly new for the research of the three-dimensional stretching/shrinking forced convection flow and heat transfer nanofluids. The nanofluid is a water-based nanofluid (H₂O), which contains one type of nanoparticles, namely, copper (Cu). Of course, the analysis can be further extended considering other types of nanoparticles such as alumina (Al₂O₃). The authors assume that the thermal equilibrium is reached for the base fluid together with the suspended nanoparticles and that the nanoparticles are uniform in dimension and form.

The purpose of this article is through a systematic literature review (SLR) to present a conceptual approach to the importance of communication for thermalism. An in-depth analysis of scientific publications provides a conceptual understanding about the definition of thermalism and the importance of communication in the thermal sector. The intention is also to identify the major challenges for communication in thermalism in times of crisis. The literature on conceptual approaches in the field of thermalism is almost non-existent, and this is an important contribution of the research presented.

To achieve the objectives, an SLR was carried out, through the Preferred Reporting Items Systematic Reviews and Meta-Analysis (PRISMA) Statement method, using the Web of Science and Scopus databases. A total of 139 articles were found, of which only 26 were used for the qualitative analysis. EndNote 20 and Nvivo software were used to identify the articles for the study, their analysis and systematization of the collected information.

The results, among others, through an in-depth analysis of scientific publications, clarified the definition of thermalism and provided relevant results for better understanding of the importance of the dimensions of communication for thermalism.

The research addresses the current scarcity of academic work on the importance of communication applied to a thermal destination and the lack of relevant strategic models for the diffusion/promotion of a destination. Finally, a limitation was the fact that only 2 databases were considered and only journal articles were included. As a future line of research the authors propose extending the theme to thermal tourism experiences. In addition, scientific studies focusing on water-based experiences connected with thermalism are almost non-existent and very relevant for the future of the sector, as well as studies in the area of communication with the following research questions: where do tourists consult information when choosing a travel destination? and what are the appropriate communication channels to reach the thermal market?; We close this reflection by concluding that the thermal tradition, through the know-how of the medical class, the properties of thermal waters and the cultural history associated with its early days, stimulated more recently by implementing innovations, will regain its role in preserving health and well-being through thermal water and the exploitation of territories' endogenous resources. These factors are the basis through which communication sciences can create strategies adapted to each country to promote a thermal destination brand.

Research in tourism destination management has provided solutions, through communication, to problems that are faced daily by countries, and the authors hope this research also contributes to the recovery of thermal tourism destinations in times of crisis. It is also from this perspective that based on the main themes and dimensions of communication identified in the SLR that the authors propose the Corporate, Organisational, Skills, Management and Online (COSMO) model to help promote resilient thermal destinations prepared for future crises. The diversity and originality of this research model will be useful for destination promoters, spa managers and communication professionals.

This study contributes to the literature by providing a theoretical framework of excellence in thermalism. One possible way to solve the ambiguity of terms related to thermalism is to consider another more comprehensive term as a combination of different approaches. The aim is not to create an academic division, but rather to contribute to better conceptual understanding, from a theoretical and paradigmatic perspective, of what thermalism is. Here, a new targeted and more comprehensive concept emerges, which from the academic perspective of communication sciences will lead to prevention for a new way of feeling good with life, contributing to promoting thermal destinations in the world with a greater understanding.

For better understanding of the concepts, this study proposes a new definition of thermalism. As research related to thermal destinations, through communication management contributes to attract tourists, promote experiences, provide the human capital of the sector with skills and create authentic and resilient place brands. It is from this perspective that the model was proposed, based on the dimensions of communication related to the main themes obtained through the SLR. This model supports a plurality of communication strategies, with different characteristics and objectives but which meet a collective purpose: to disseminate information about thermalism, in order to build collective knowledge to promote thermal destinations. The analysis highlights the need for further research into thermalism, with special focus on communication.