Search results

1 – 10 of 235
Article
Publication date: 28 August 2019

Fatemeh FaghihKhorasani, Mohammad Zaman Kabir, Mehdi AhmadiNajafabad and Khosrow Ghavami

The purpose of this paper is to provide a method to predict the situation of a loaded element in the compressive stress curve to prevent failure of crucial elements in…

Abstract

Purpose

The purpose of this paper is to provide a method to predict the situation of a loaded element in the compressive stress curve to prevent failure of crucial elements in load-bearing masonry walls and to propose a material model to simulate a compressive element successfully in Abaqus software to study the structural safety by using non-linear finite element analysis.

Design/methodology/approach

A Weibull distribution function was rewritten to relate between failure probability function and axial strain during uniaxial compressive loading. Weibull distribution parameters (shape and scale parameters) were defined by detected acoustic emission (AE) events with a linear regression. It was shown that the shape parameter of Weibull distribution was able to illustrate the effects of the added fibers on increasing or decreasing the specimens’ brittleness. Since both Weibull function and compressive stress are functions of compressive strain, a relation between compressive stress and normalized cumulative AE hits was calculated when the compressive strain was available. By suggested procedures, it was possible to monitor pretested plain or random distributed short fibers reinforced adobe elements (with AE sensor and strain detector) in a masonry building under uniaxial compression loading to predict the situation of element in the compressive stress‒strain curve, hence predicting the time to element collapse by an AE sensor and a strain detector. In the predicted compressive stress‒strain curve, the peak stress and its corresponding strain, the stress and strain point with maximum elastic modulus and the maximum elastic modulus were predicted successfully. With a proposed material model, it was illustrated that the needed parameters for simulating a specimen in Abaqus software with concrete damage plasticity were peak stress and its corresponding strain, the stress and strain point with maximum elastic modulus and the maximum elastic modulus.

Findings

The AE cumulative hits versus strain plots corresponding to the stress‒strain curves can be divided into four stages: inactivity period, discontinuous growth period, continuous growth period and constant period, which can predict the densifying, linear, non-linear and residual stress part of the stress‒strain relationship. By supposing that the relation between cumulative AE hits and compressive strain complies with a Weibull distribution function, a linear analysis was conducted to calibrate the parameters of Weibull distribution by AE cumulative hits for predicting the failure probability as a function of compressive strain. Parameters of m and θ were able to predict the brittleness of the plain and tire fibers reinforced adobe elements successfully. The calibrated failure probability function showed sufficient representation of the cumulative AE hit curve. A mathematical model for the stress–strain relationship prediction of the specimens after detecting the first AE hit was developed by the relationship between compressive stress versus the Weibull failure probability function, which was validated against the experimental data and gave good predictions for both plain and short fibers reinforced adobe specimens. Then, the authors were able to monitor and predict the situation of an element in the compressive stress‒strain curve, hence predicting the time to its collapse for pretested plain or random distributed short fibers reinforced adobe (with AE sensor and strain detector) in a masonry building under uniaxial compression loading by an AE sensor and a strain detector. The proposed model was successfully able to predict the main mechanical properties of different adobe specimens which are necessary for material modeling with concrete damage plasticity in Abaqus. These properties include peak compressive strength and its corresponding axial strain, the compressive strength and its corresponding axial strain at the point with maximum compressive Young’s modulus and the maximum compressive Young’s modulus.

Research limitations/implications

The authors were not able to decide about the effects of the specimens’ shape, as only cubic specimens were chosen; by testing different shape and different size specimens, the authors would be able to generalize the results.

Practical implications

The paper includes implications for monitoring techniques and predicting the time to the collapse of pretested elements (with AE sensor and strain detector) in a masonry structure.

Originality/value

This paper proposes a new method to monitor and predict the situation of a loaded element in the compressive stress‒strain curve, hence predicting the time to its collapse for pretested plain or random distributed short fibers reinforced adobe (with AE sensor and strain detector) in a masonry building under uniaxial compression load by an AE sensor and a strain detector.

Article
Publication date: 24 October 2023

Quan-Pu Liu, Jia Kang, Long-Xu Tan, Si-Yu Wang, Otto Bruhns and Heng Xiao

This paper aims to present a direct analysis to demonstrate why markedly different tensile and compressive behaviors of concretes could not be simulated with the Drucker–Prager…

Abstract

Purpose

This paper aims to present a direct analysis to demonstrate why markedly different tensile and compressive behaviors of concretes could not be simulated with the Drucker–Prager yield criterion.

Design/methodology/approach

This study proposed an extended form of the latter for establishing a new elastoplasticity model with evolving yield strengths.

Findings

Explicit closed-form solutions to non-symmetric tensile and compressive responses of uniaxial specimens at finite strain are for the first time obtained from hardening to softening.

Originality/value

With such exact solutions, the yield strengths in tension and compression can be explicitly prescribed by uniaxial tensile and compressive stress-strain functions. Then, the latter two are further provided in explicit forms toward accurately simulating tensile and compressive behaviors. Numerical examples are supplied for meso-scale heterogeneous concrete (MSHC) and high-performance concrete (HPC), etc. Model predictions are in good agreement with test data.

Details

Multidiscipline Modeling in Materials and Structures, vol. 19 no. 6
Type: Research Article
ISSN: 1573-6105

Keywords

Article
Publication date: 1 June 1995

R.V. Balendran

Discusses the results of a study of the moduli of elasticity ofconcretes made with artificially manufactured lightweight aggregatessubjected to uniaxial compression and uniaxial

3491

Abstract

Discusses the results of a study of the moduli of elasticity of concretes made with artificially manufactured lightweight aggregates subjected to uniaxial compression and uniaxial tension. Two artificially manufactured lightweight aggregates and one normal weight aggregate (for comparison) were used in the investigation. Concrete mixes designed to have compressive strengths varying from 20 MPa to 60 MPa were used in this study. Presents the results of static and dynamic moduli of elasticity, Poisson′s ratio, ultrasonic pulse velocity, compressive strength and tensile strength tests. Observes that the static modulus of elasticity in tension is nearly equal to the static modulus of elasticity in compression at a stress level of one‐third the ultimate stress. Compressive modulus values are shown to be dependent on the stress level and type of modulus, i.e. either secant or tangent. On the other hand, the tensile modulus is not affected by the stress level. The modulus of elasticity of lightweight aggregate concrete is about 60‐70 per cent of that of normal weight concrete. Compares the test results obtained in this study with research work carried out on other lightweight aggregate concretes by other investigators. Also presents the relationships between static modulus of elasticity, dynamic modulus of elasticity, compressive strength, and Poisson′s ratio, and equations for estimating elastic modulus and Poisson′s ratio.

Details

Structural Survey, vol. 13 no. 2
Type: Research Article
ISSN: 0263-080X

Keywords

Article
Publication date: 4 August 2021

Pandimani, Markandeya Raju Ponnada and Yesuratnam Geddada

This study aims to present comprehensive nonlinear material modelling techniques and simulations of reinforced concrete (RC) beams subjected to short-term monotonic static load…

Abstract

Purpose

This study aims to present comprehensive nonlinear material modelling techniques and simulations of reinforced concrete (RC) beams subjected to short-term monotonic static load using the robust and reliable general-purpose finite element (FE) software ANSYS. A parametric study is carried out to analyse the flexural and ductility behaviour of RC beams under various influencing parameters.

Design/methodology/approach

To develop and validate the numerical FE models, a total of four experimentally tested simply supported RC beams are taken from the available literature and two beams are selected from each author. The concrete, steel reinforcements, bond-slip mechanism, loading and supporting plates are modelled using SOLID65, LINK180, COMBIN39 and SOLID185 elements, respectively. The validated models are then used to conduct parametric FE analysis to investigate the effect of concrete compressive strength, percentage of tensile reinforcement, compression reinforcement ratio, transverse shear reinforcement, bond-slip mechanism, concrete compressive stress-strain constitutive models, beam symmetry and varying overall depth of beam on the ultimate load-carrying capacity and ductility behaviour of RC beams.

Findings

The developed three-dimensional FE models can able to capture the load and midspan deflections at critical points, the accurate yield point of steel reinforcements, the formation of initial and progressive concrete crack patterns and the complete load-deflection curves of RC beams up to ultimate failure. From the numerical results, it can be concluded that the FE model considering the bond-slip effect with Thorenfeldt’s concrete compressive stress-strain model exhibits a better correlation with the experimental data.

Originality/value

The ultimate load and deflection results of validated FE models show a maximum deviation of less than 10% and 15%, respectively, as compared to the experimental results. The developed model is also capable of capturing concrete failure modes accurately. Overall, the FE analysis results were found quite acceptable and compared well with the experimental data at all loading stages. It is suggested that the proposed FE model is a practical and reliable tool for analyzing the flexural behaviour of RC members and can be used for performing parametric studies.

Details

World Journal of Engineering, vol. 20 no. 1
Type: Research Article
ISSN: 1708-5284

Keywords

Article
Publication date: 30 December 2020

Florian Hüter and Frank Rieg

A general first-invariant constitutive model has been derived in literature for incompressible, isotropic hyperelastic materials, known as Marlow model, which reproduces test data…

Abstract

Purpose

A general first-invariant constitutive model has been derived in literature for incompressible, isotropic hyperelastic materials, known as Marlow model, which reproduces test data exactly without the need of curve-fitting procedures. This paper aims to describe how to extend Marlow’s constitutive model to the more general case of compressible hyperelastic materials.

Design/methodology/approach

The isotropic constitutive model is based on a strain energy function, whose isochoric part is solely dependent on the first modified strain invariant. Based on Marlow’s idea, a principle of energetically equivalent deformation states is derived for the compressible case, which is used to determine the underlying strain energy function directly from measured test data. No particular functional of the strain energy function is assumed. It is shown how to calibrate the volumetric and isochoric strain energy functions uniquely with uniaxial or biaxial test data only. The constitutive model is implemented into a finite element program to demonstrate its applicability.

Findings

The model is well suited for use in finite element analysis. Only one set of test data is required for calibration without any need for curve-fitting procedures. These test data are reproduced exactly, and the model prediction is reasonable for other deformation modes.

Originality/value

Marlow’s basic concept is extended to the compressible case and applied to both the volumetric and isochoric part of the compressible strain energy function. Moreover, a novel approach is described on how both compressive and tensile test data can be used simultaneously to calibrate the model.

Details

Engineering Computations, vol. 38 no. 6
Type: Research Article
ISSN: 0264-4401

Keywords

Article
Publication date: 14 June 2019

Abdurra’uf M. Gora, Jayaprakash Jaganathan, M.P. Anwar and H.Y. Leung

Advanced fibre-reinforced polymer (FRP) composites have been increasingly used over the past two decades for strengthening, upgrading and restoring degraded civil engineering…

Abstract

Purpose

Advanced fibre-reinforced polymer (FRP) composites have been increasingly used over the past two decades for strengthening, upgrading and restoring degraded civil engineering infrastructure. Substantial experimental investigations have been conducted in recent years to understand the compressive behaviour of FRP-confined concrete columns. A considerable number of confinement models to predict the compressive behaviour of FRP-strengthened concrete columns have been developed from the results of these experimental investigations. The purpose of this paper is to present a comprehensive review of experimental investigations and theoretical models of circular and non-circular concrete columns confined with FRP reinforcement.

Design/methodology/approach

The paper reviews previous experimental test results on circular and non-circular concrete columns confined with FRP reinforcement under concentric and eccentric loading conditions and highlights the behaviour and mechanics of FRP confinement in these columns. The paper also reviews existing confinement models for concrete columns confined with FRP composites in both circular and non-circular sections.

Findings

This paper demonstrates that the performance and effectiveness of FRP confinement in concrete columns have been extensively investigated and proven effective in enhancing the structural performance and ductility of strengthened columns. The strength and ductility enhancement depend on the number of FRP layers, concrete compressive strength, corner radius for non-circular columns and intensity of load eccentricity for eccentrically loaded columns. The impact of existing theoretical models and directions for future research are also presented.

Originality/value

Potential researchers will gain insight into existing experimental and theoretical studies and future research directions.

Details

World Journal of Engineering, vol. 16 no. 4
Type: Research Article
ISSN: 1708-5284

Keywords

Article
Publication date: 1 August 2000

Pankaj and Khalid Moin

Plane strain constitutive behaviour of von Mises and isotropic Hoffman materials is examined using single element tests. Two kinds of tests are conducted – (a) prescribed…

Abstract

Plane strain constitutive behaviour of von Mises and isotropic Hoffman materials is examined using single element tests. Two kinds of tests are conducted – (a) prescribed displacement tests; and (b) tests with a mixture of displacements and boundary tractions prescribed. While (a) are used to understand the manner of stress traversal on the yield surface in principal stress space, (b) are employed to study the load displacement response and the possibility of ensuing localization. Associated plasticity is assumed throughout. The tests are conducted using perfect and strain softening plasticity. It is found that for the von Mises criterion limited exact solutions can be evolved even under softening (or hardening) conditions. For isotropic Hoffman materials the nature of the stress traversal, load deflection response and the satisfaction of the localization conditions are strongly influenced by the ratio and difference of uniaxial yield strengths, in tension and compression, as well as by the softening parameters.

Details

Engineering Computations, vol. 17 no. 5
Type: Research Article
ISSN: 0264-4401

Keywords

Article
Publication date: 1 June 2006

J. Pina‐Henriques and Paulo B. Lourenço

To contribute for a reliable estimation of the compressive strength of unreinforced masonry from the properties of the constituents (units and mortar).

1831

Abstract

Purpose

To contribute for a reliable estimation of the compressive strength of unreinforced masonry from the properties of the constituents (units and mortar).

Design/methodology/approach

Sophisticated non‐linear continuum models, based on damage, plasticity, cracking or other formulation, are today standard in several finite element programs. The adequacy of such models to provide reliable estimates of masonry compressive strength, from the properties of the constituents, remains unresolved. The authors have shown recently that continuum models might significantly overestimate the prediction of the compressive strength. Hence, an alternative phenomenological approach developed in a discrete framework is proposed, based on attributing to masonry components a fictitious micro‐structure composed of linear elastic particles separated by non‐linear interface elements. The model is discussed in detail and a comparison with experimental results and numerical results using a standard continuum model is provided.

Findings

Clear advantages in terms of compressive strength and peak strain prediction were found using the particle model when compared with standard continuum models. Moreover, compressive and tensile strength values provided by the model were found to be particle size‐ and particle distortion‐independent for practical purposes. It is also noted that size‐dependent responses were obtained and that shear parameters rather than tensile parameters were found to play a major role at the meso‐level of the phenomenological model.

Originality/value

This paper provides further insight into the compressive behaviour of quasi‐brittle materials, with an emphasis on the strength prediction of masonry composites. Reliable prediction of masonry strength is of great use in the civil engineering field, allowing one to reduce experimental testing in expensive wallets and to avoid the usage of conservative empirical formulae.

Details

Engineering Computations, vol. 23 no. 4
Type: Research Article
ISSN: 0264-4401

Keywords

Article
Publication date: 7 November 2019

Vijay Kumar Polimeru and Arghadeep Laskar

The purpose of this study is to evaluate the effectiveness of two-dimensional (2D) cyclic softened membrane model (CSMM)-based non-linear finite element (NLFE) model in predicting…

Abstract

Purpose

The purpose of this study is to evaluate the effectiveness of two-dimensional (2D) cyclic softened membrane model (CSMM)-based non-linear finite element (NLFE) model in predicting the complete non-linear response of shear critical bridge piers (with walls having aspect ratios greater than 2.5) under combined axial and reversed cyclic uniaxial bending loads. The effectiveness of the 2D CSMM-based NLFE model has been compared with the widely used one-dimensional (1D) fiber-based NLFE models.

Design/methodology/approach

Three reinforced concrete (RC) hollow rectangular bridge piers tested under reversed cyclic uniaxial bending and sustained axial loads at the National Centre for Research on Earthquake Engineering (NCREE) Taiwan have been simulated using both 1D and 2D models in the present study. The non-linear behavior of the bridge piers has been studied through various parameters such as hysteretic loops, energy dissipation, residual drift, yield load and corresponding drift, peak load and corresponding drift, ultimate loads, ductility, specimen stiffness and critical strains in concrete and steel. The results obtained from CSMM-based NLFE model have been critically compared with the test results and results obtained from the 1D fiber-based NLFE models.

Findings

It has been observed from the analysis results that both 1D and 2D simulation models performed well in predicting the response of flexure critical bridge pier. However, in the case of shear critical bridge piers, predictions from 2D CSMM-based NLFE simulation model are more accurate. It has, thus, been concluded that CSMM-based NLFE model is more accurate and robust to simulate the complete non-linear behavior of shear critical RC hollow rectangular bridge piers.

Originality/value

In this study, a novel attempt has been made to provide a rational and robust FE model for analyzing shear critical hollow RC bridge piers (with walls having aspect ratios greater than 2.5).

Details

Engineering Computations, vol. 37 no. 1
Type: Research Article
ISSN: 0264-4401

Keywords

Article
Publication date: 10 April 2017

Mojtaba Labibzadeh, Mojtaba Zakeri and Abdol Adel Shoaib

The purpose of this paper is to present a new method for determining the input parameters of the concrete damaged plasticity (CDP) model of ABAQUS standard software. The existing…

1088

Abstract

Purpose

The purpose of this paper is to present a new method for determining the input parameters of the concrete damaged plasticity (CDP) model of ABAQUS standard software. The existing available methods in the literatures are case sensitive, i.e., they give different input parameters of CDP for a unique concrete class used in different finite element (FE) simulation of concrete structures. In this study, the authors attempt to introduce a new approach for the identification of the input parameters of the CDP model, which guarantees the uniqueness and precision of the model. In other words, by this method, the input parameters obtained for a specific concrete class with a unique characteristic strength can be used for FE simulation of the different concrete structures which were constructed by this concrete without the need to additional modifications raised from any new application.

Design/methodology/approach

For the input parameter identification of the CDP model, different standard tests of plain concrete are simulated by the ABAQUS standard software. These test simulations are performed for various set of input parameters. In the end, those set of input parameters which represents the best curve fitting with the experimental results is chosen as the optimum parameters.

Findings

By comparison of the FE simulation results obtained from the ABAQUS for two different concrete structures using the proposed input parameters for the CDP model with the experimental results, it was shown that the presented method for determining those parameters can guarantee the uniqueness and precision of the CDP model in simulation.

Originality/value

The method described for determining the input parameters of the CDP model of the ABAQUS standard software has not been previously presented.

Details

International Journal of Structural Integrity, vol. 8 no. 2
Type: Research Article
ISSN: 1757-9864

Keywords

1 – 10 of 235