Search results

The purpose of this study is to numerically examine the heat transfer and transport of space charges in the solid insulating materials [low density polyethylene (LDPE), flame retardant type 4 (FR4), Polytetrafluoroethylene (PTFE)] using the transmission line modeling (TLM) method. Besides, a comprehensive study is performed on the mutual influences of heat transfer and space charges transport within the solid dielectric bulk.

The obtained governing equations including continuity and circuit equations are coupled with heat transfer equations, and they are solved via fourth-order Runge–Kutta method.

The electric potential and field, current density and temperature distribution are calculated. It is shown that compared with FR4 and PTFE, the temperature increment rate in LDPE is much lower. Moreover, the heat transfer in the solid insulating materials bulk increases the homo-charges density and temperature in the vicinity of electrodes. Hence, the reduction in electric field is reflected in the potential deformations in the proximity of electrodes. Furthermore, where the electric field is maximized, the temperature is minimized.

This study is restricted to two-dimensional problems.

Interestingly, because of the lower temperature in LDPE, the current density and their increment rates in LDPE are much lower than that in FR4 and PTFE dielectric materials.

The purpose of this paper is to explore and develop specific models of the kinetics of isothermal depolarization currents (IDC) and the corresponding methods for the diagnostics of the physical parameters of localized electronic states (LES) in heterogeneous materials and corresponding polycrystalline semiconductor materials and heterogeneous insulators with a conductive phase.

Analysis of the kinetics of isothermal depolarization on the basis of the models allowed the authors to establish a sufficient level of their information content. This also allowed the possibility of applying for research and testing of heterogeneous structures of electronic technique.

Optimal conditions (full charge of LES on one side of the object and full discharge on the other side) and the correction factors, allowed the researchers to find concentration of these states using the developed models.

This paper uses a particular method to determine and test the parameters of LES, including operations of determining the time constant of IDC signal from its frequency spectrum, finding the ionization energy and the capture coefficient of electrons from the temperature dependence of this time constant, determining the concentration based on the integration of the time dependence of current density of IDC in the time interval that boundaries are determined from the limited range of frequencies of the signal IDC spectrum has been proposed, validated and verified by numerical experiments.

The purpose of this paper is to present numerical studies on thermally induced vibrations of piezo‐thermo‐viscoelastic composite beam subjected to a transient thermal load using coupled finite element method.

The thermal relaxation and viscoelastic relaxations are taken into consideration to obtain the system response. The concept of “memory load” along with the thermal relaxation is accounted for viscoelastic core material. The influence of type of core material on the response of the system also analyzed.

The findings show viscoelastic behavior with relaxation times in composite sandwich structures.

The paper shows accounting relaxation times as a memory load in composite sandwich structures.

The paper proposes and presents a comprehensive and integrated circuit model for investigating the behaviour of partial discharges occurring in voids inside the solid insulations of medium and high voltage cables.

The model is based on the well‐known three capacitors model, which is remarkably improved to handle physical parameters such as cavity size, position, shape and pressure, environmental parameters such as cable temperature, in addition to operational parameters such as the contributions of the avalanche of free electrons inside the cavity through considering stochastic time delays.

A complete, flexible and reliable model for partial discharges in voids inside the solid insulation of medium and high voltage cables is presented whose output agrees with experimental reported results.

The proposed model deals only with single voids, and the semiconductor layers in the insulation of cables are not considered.

The model can be used in different physical, environmental and operational conditions in order to investigate the characteristics of partial discharge signals to be used as the bases for partial discharge detection and classification in power cables.

This paper presents a novel comprehensive and integrated circuit model with controlling functions to propose the behaviour of partial discharge occurring in voids inside the solid insulation of power cables. The model provides the contribution of geometrical parameters of the void, and operational conditions such as cable temperature and source frequency in partial discharge analysis.

High voltage direct current (HVDC) cable is an important part in the electric power transmission and distribution systems. However, very little research has been carried out on partial discharge under direct current (DC) conditions. Niemeyer’s model has been widely used under alternating current (AC) conditions. This paper aims to intend to modify the Niemeyer’s model considering both electric field and charge dynamics under DC conditions, and therefore proposes a numerical model describing partial discharge characteristics in HVDC cable.

This paper intends to understand partial discharge characteristics under DC conditions through numerical modelling. Niemeyer’s model that has been widely used under AC conditions has been modified, taking both electric field and charge dynamics under DC conditions into consideration. The effects of loading level or current through the conductor, cavity location and material properties on partial discharges have also been studied.

Electrical conductivity is important in determining the characteristics of partial discharge under DC conditions and discharges tend to happen in short when the cavity field exceeds the inception level under the parameter values studied in the paper.

Building the numerical model is the purpose of the paper, and there is lack in experiment and the comparison between the simulation results and experiment.

The proposed model provides the numerical model describing partial discharge in HVDC cable and helps understand the partial discharge mechanism under DC voltage.

To the best of the author’s knowledge, this paper is a very early research on the numerical modelling work on partial discharge under DC voltage.

The purpose of this paper is to develop the models of the dielectric permittivity dispersion of heterogeneous systems based on semiconductors to a level that would allow to apply effectively the method of broadband dielectric spectroscopy for the study of electronic processes in ceramic and composite materials.

The new approach for determining the complex dielectric permittivity of heterogeneous systems with semiconductor particles is used. It includes finding the analytical expression of the effective dielectric permittivity of the separate semiconductor particle of spherical shape. This approach takes into account the polarization of the free charge carriers in this particle, including capturing to localized electron states. This enabled the authors to use the known equations for complex dielectric permittivity of two-component matrix systems and statistical mixtures.

The presented dispersion equations establish the relationship between the parameters of the dielectric spectrum and electronic processes in the structures like semiconductor particles in a dielectric matrix in a wide frequency range. Conditions of manifestation and location of the different dispersion regions of the complex dielectric heterogeneous systems based on semiconductors in the frequency axis and their features are established. The most high-frequency dispersion region corresponds to the separation of free charge carriers at polarization. After this region in the direction of reducing of the frequency, the dispersion regions caused by recharge bulk and/or surface localized states follow. The most low-frequency dispersion region is caused by recharging electron traps in the boundary layer of the dielectric matrix.

Dielectric dispersion models are developed that are associated with: electronic processes of separation of free charge carriers in the semiconductor component, recapture of free charge carriers in the localized electronic states in bulk and on the surface of the semiconductor and also boundary layers of the dielectric at the polarization. The authors have analyzed to situations that correspond applicable and promising materials: varistor ceramics and composite structure with conductive and semiconductor fillers. The modelling results correspond to the existing level of understanding of the electron phenomena in matrix systems and statistical mixtures based on semiconductors. It allows to raise efficiency of research and control properties of heterogeneous materials by dielectric spectroscopy.

The purpose of this study is to introduce a new type of sensor which uses microwave metamaterials and direct-coupled split-ring resonators (DC-SRRs) to measure the dielectric properties of solid materials in real time. The sensor uses a transmission line with a bridge-type structure to measure the differential frequency, which can be used to calculate the dielectric constant of the material being tested. The study aims to establish an empirical relationship between the dielectric properties of the material and the frequency measurements obtained from the sensor.

In the proposed design, the opposite arm of the bridge transmission line is loaded by DC-SRRs, and the distance between DC-SRRs is optimized to minimize the mutual coupling between them. The DC-SRRs are loaded with the material under test (MUT) to perform differential permittivity sensing. When identical MUT is placed on both resonators, a single transmission zero (notch) is obtained, but non-identical MUTs exhibit two split notches. For the design of differential sensors and comparators based on symmetry disruption, frequency splitting is highly useful.

The proposed structure is demonstrated using electromagnetic simulation, and a prototype of the proposed sensor is fabricated and experimentally validated to prove the differential sensing principle. Here, the sensor is analyzed for sensitivity by using different MUTs with relative permittivity ranges from 1.006 to 10 and with a fixed dimension of 9 mm × 10 mm ×1.2 mm. It shows a very good average frequency deviation per unit change in permittivity of the MUTs, which is around 743 MHz, and it also exhibits a very high average relative sensitivity and quality factor of around 11.5% and 323, respectively.

The proposed sensor can be used for differential characterization of permittivity and also as a comparator to test the purity of solid dielectric samples. This sensor most importantly strengthens robustness to environmental conditions that cause cross-sensitivity or miscalibration. The accuracy of the measurement is enhanced as compared to conventional single- and double-notch metamaterial-based sensors.

This paper aims to report on fabrication procedure and presents microstructure and dielectric behaviour of LiZn_0.92Cu_0.08PO₄ ceramic material with Li₂CO₃ as a sintering aid.

Substrates based on LiZn_0.92Cu_0.08PO₄ with Li₂CO₃ addition were prepared via solid-state synthesis, doping, milling, pressing and sintering. Characterization of the composition, microstructure and dielectric properties was performed using X-ray diffractometry, energy dispersive spectroscopy, scanning electron microscopy, impedance spectroscopy in the 100 Hz to 2 MHz range and time-domain spectroscopy in the 0.1–3 THz range.

Doped LiZnPO₄ ceramic, which exhibits a low dielectric constant of 5.9 at 1 THz and low sintering temperature of 800 °C, suitable for low temperature co-fired ceramics (LTCC) technology, was successfully prepared. However, further studies are needed to lower dielectric losses by optimising the doping level, synthesis and sintering conditions.

Search for new low dielectric constant materials applicable in LTCC technology and optimization of processing are essential tasks for developing modern microwave circuits. The dielectric characterization of doped LiZnPO₄ ceramic in the terahertz range, which was performed for the first time, is crucial for potential millimetre-wave applications of this substrate material.

This paper aims to concentrate on research that has been conducted in the previous decade on metamaterial (MTM)-based sensors for material characterization, which includes solid dielectrics, micro fluids and biomolecules.

There has been a vast advancement in sensors based on MTM since the past few decades. MTM elements provide a sensitive response to materials while having a tiny footprint, making them an appealing alternative for realizing diverse sensing devices.

Related research papers on MTM sensors published in reputable journals were reviewed in this report, with a specific emphasis on the structure, size and nature of the materials characterized. Because electromagnetic wave interaction excites MTM structures, sensing applications around the electromagnetic spectrum are possible.

The paper contains valuable information on MTM sensor technology for material characterization, and this study also highlights the challenges and approaches that will guide future development.

A major drawback of current copper thick‐film technology is the inefficient removal of the organic binder associated with the dielectric material in the low‐oxygen inert gas (N2) atmosphere of the furnace. In processing large area and/or multilayer substrates, the incomplete binder removal causes deleterious effects which have been well documented. Therefore, it is necessary to remove hydrocarbons and residual carbon from the films in the burn‐out section of the furnace before the films begin developing their characteristic microstructures. However, the atmosphere currently employed is not capable of removing all the carbon and hydrogen in the form of gaseous oxides. In literature, in addition to furnace modifications, several atmosphere modifications and manipulations have been proposed to achieve optimum properties for the fired films. With few exceptions, the scientific basis for such atmosphere modifications and manipulations has been left either unaddressed or obscure. With this background, this paper examines the feasibility of using a reactive gas mixture in the furnace to achieve efficient organic binder removal. Phase stability diagrams are presented to illustrate the stability of (i) carbon, (ii) thick film copper ingredients, (iii) active phases of resistors, and (iv) components of glassy and crystalline phases of dielectrics in selected reactive atmospheres. The stability of certain furnace belt constituents is also addressed. Mass balance calculations are shown to demonstrate the extent of carbon removal and copper oxidation in typical nitrogen atmospheres. Based on the interpretation of thermodynamic data and reaction mechanisms involved, a specific H2‐H2O mixture with nitrogen as the carrier gas is recommended. The approach presented here constitutes a general analytical scheme to understand materials‐atmosphere interactions occurring across a temperature range. Several issues in furnace design are also discussed from the standpoint of gas‐solid reaction kinetics. These deal with the design of gas‐flow systems that facilitate removal of organic binders.