Search results

The demand for titanium alloys has received massive attention in the aerospace and automotive industry owing to their magnificent electrochemically compatibility and corrosion resistance, high strength at elevated temperatures and high strength-to-weight ratio. Although titanium alloy has impressive mechanical properties, they are challenging to machine or metal form due to its poor heat conductivity, high chemical reactivity, low modulus of elasticity, high friction coefficient and difficult lubricant that limits its application field and increases wear. However, surface treatment coating with the strong metallurgical bond between the titanium alloy matrixes is novel technique to resolve these challenges. This research will illustrate the influence of laser scanning power on the microstructure and tribological behavior of Nickel (NI)-composite claddings fabricated on TC4 titanium alloy to realize the strong metallurgical bond between the titanium alloy and NI-composite coating.

In this research, TiC/TC4 alloy nanocomposites were fabricated based on different laser power and temperatures. TC4 has been selected as a base material instead of TiC for the strong metallurgical bond between the titanium alloy matrixes. Then Ni-composite coating was used as the surface treatment coating on TC4 by laser cladding (LC) technique. The Ni-based alloy coating material powder is good self-fluxing, has high-temperature resistance and is analytically pure with 200 mesh, which can easily overcome the various challenges of titanium alloy. The chemical properties of Ni composite coating include 31.2% Chromium, 8%Titenium and 3.6% Carbon. The prepared surface treatment coating characterization and microstructure behavior are analyzed using optical micrograph, X-ray diffraction, scanning electron microscopes, energy dispersive spectroscopy and electron probe micro analyzer methods.

It is evident that at the beginning of the experiment, if the laser power increased, the quality of the coating increased. An optimal quality of the coating is found when the laser scanning power about 12.55 kJ/cm². Further increased laser power diminished the quality of the coating because the material plasticity had deteriorated. The TiC ceramic particle reinforced phase is dispersed into a two-phase solid solution of β-Ti and γ-Ni. The micro-hardness of the used coating is greater than the base alloy.

This research has practical value in the modern aerospace and automobile industry to increase the application of titanium alloy.

The purpose of this study is to reveal the effect of nano-Al₂O₃ particle addition on the nucleation/growth kinetics, microhardness, wear resistance and corrosion resistance of Co–P–xAl₂O₃ nanocomposite plating.

The kinetics and properties of Co–P–xAl₂O₃ nanocomposite plating prepared by electroplating were investigated by electrochemical measurements, scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Vickers microhardness measurement, SRV5 friction and wear tester and atomic force microscopy.

A 12 g/L nano-Al₂O₃ addition in the plating solution can transform the nucleation/growth kinetics of the plating from the 3D progressive model to the 3D instantaneous model. The microhardness of the plating increased with the increase of nano-Al₂O₃ content in plating. The wear resistance of the plating did not adhere strictly to Archard’s law. An even and denser corrosion product film was generated due to the finer grains, with a high corrosion resistance.

The effect of different nano-Al₂O₃ addition on the nucleation/growth kinetics and properties of Co–P–xAl₂O₃ nanocomposite plating was investigated, and an anticorrosion mechanism of Co–P–xAl₂O₃ nanocomposite plating was proposed.

Sai Coating, a small entrepreneurial firm, was one of the three firms that had received the license from ARCI for marketing the Detonation Spray Coating (DSC). Sai Coating made and sold the detonation gun (D-Gun) to three sectors, namely: Wire Drawing, Textiles and Aero components. The coating enhanced the life of the coated wire or surface and its functionality in some ways. The firm had a turnover of INR 4,500,000 and was looking to generate scale and maximize its revenues. The case revolves around the pricing strategy to be adopted by Sai coating to extract value from different set of customers. What should be the price levels given the nature of the product?

The purpose of this study is to prolong the service life of the Al–Si alloy cylinder and achieve the objective of energy saving and emission reduction by the composite treatments.

Chemical etching + laser texturing + filled MoS₂ composite treatment was applied to the friction surface of aluminum–silicon (Al–Si) alloy cylinder. The friction coefficient and wear loss were measured to characterize the tribology property of cylinders.

The composite-treated Al–Si alloy cylinder had the lowest friction coefficient and weight loss. The friction coefficient and weight loss of the composite treatment were approximately 27.08% and 54.17% lower than those of the untreated sample, respectively. The laser micro-textures control the release of solid lubricant to the interface of friction pairs slowly, which prolongs the service life of cylinders.

The synergistic effect of the chemical etching + laser texturing + filled MoS2 modified the tribology properties of Al–Si alloy cylinder. The chemical etching raised the silicon particles to bear the load, and laser micro-textures control the release of solid lubricant to improve the lubrication property.

This paper aims to design the nano-titanium dioxide (TiO₂) coating system which has superhydrophilic property, self-cleaning mechanism and antifog property as well as strong adhesion on glass substrate.

Two hydrophilic materials have been used such as TiO₂ nanoparticles as fillers and hydrophilic copolymer, Pluronic F-127 by using simple sol–gel approach. The prepared solution was applied onto glass through dip- and spray-coating techniques and then left for drying at ambient temperature.

The nano-TiO₂ superhydrophilic coating has achieved the water contact angle of 4.9° ± 0.5°. The superhydrophilic coating showed great self-cleaning effect against concentrated syrup and methylene blue where thin layer of water washes the dirt contaminants away. The nano-TiO₂ coating exhibits great antifog performance that maintains high transparency of around 89% when the coated glass is placed above hot-fog vapor for 10 min. The fog droplets were condensed into water film which allowed the transmission of light through the glass. The strong adhesion of coated glass shows no total failure at scratch profile when impacted with scratch load of 500, 800 and 1,200 mN.

Findings will be useful in the development of self-cleaning superhydrophilic coating that is applicable on building glass and photovoltaic panel.

The developed nano-TiO₂ coating is developed by the combination of hydrophilic organic copolymer–inorganic TiO₂ network to achieve great superhydrophilic property, optimum self-cleaning ability and supreme antifog performance.

The findings will be useful for residents in building glass window where the application will reduce dust accumulation and keep the glass clean for longer period.

The synthesis of nano-TiO₂ superhydrophilic coating which can be sprayed on large glass panel and cured at ambient temperature.

This paper aims to figure out the conundrum that the corrosion resistance longevity of steel wires for bridge cables was arduous to meet the requirements.

The “two-step” hot-dip coating process for cable steel wires was developed, which involved first hot-dip galvanizing and then hot-dip galvanizing of aluminum magnesium alloy. The corrosion rate, polarization curve and impedance of Zn–6Al–1Mg and Zn–10Al–3Mg alloy-coated steel wires were compared through acetate spray test and electrochemical test, and the corrosion mechanism of Zn–Al–Mg alloy-coated steel wires was revealed.

The corrosion resistance of Zn–10Al–3Mg alloy-coated steel wires had the best corrosion resistance, which was more than seven times that of pure zinc-coated steel wires. The corrosion current of Zn–10Al–3Mg alloy-coated steel wires was lower than that of Zn–6Al–1Mg alloy-coated steel wires, whereas the capacitive arc and impedance value of the former were higher than that of the latter, making it clear that the corrosion resistance of Zn–10Al–3Mg was better than that of Zn–6Al–1Mg alloy coating. Moreover, the Zn–Al–Mg alloy-coated steel wires for bridge cables had the function of coating “self-repairing.”

Controlling the temperature and time of the hot dip galvanizing stage can reduce the thickness of transition layer and solve the problem of easy cracking of the transition layer in the Zn–Al–Mg alloy coating due to the Sandelin effect.

This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved.

In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS₂ and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2  and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel.

The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss.

The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

This paper aims to comprehensively review the preparation methods of superhydrophobic surfaces (SHPS) for corrosion protection of Mg alloy in recent years.

The preparation methods, wettability and corrosion resistance of SHPS on Mg alloy in the past three years are systematically described in this paper.

Two types of SHPS, including single-layer and multilayer coatings for corrosion protection of Mg alloy are summarized. Preparing multilayered coatings with multifunction is the current trend in developing SHPS on Mg alloy.

This paper reviewed the preparation methods and corrosion resistance of SHPS on Mg alloys. It provides a valuable reference for researchers to develop highly durable SHPS with excellent corrosion resistance for Mg alloys.

This paper aims to investigate the high temperature corrosion behaviour of ZrO₂-reinforced Cr₂O₃ matrix-based composite coatings on ASTM-SA213-T-22 steel at 900°C in molten salt environment. The different coatings were deposited by high velocity oxy fuel (HVOF) method.

Hot corrosion studies were conducted in simulated boiler environment in silicon carbide tube furnace at 900°C for 50 cycles on bare and HVOF-coated boiler steel specimens. Each cycle consisted 50 h of heating in the simulated boiler environment followed by 20 min of cooling in air. The weight change measurements were performed after each cycle to establish the kinetics of corrosion using thermogravimetric technique. X-ray diffraction and scanning electron microscopy techniques were used to analyse the corroded specimens.

The addition of 20 Wt.% ZrO₂ in Cr₂O₃ helped reduce corrosion rate by 89.25% as compared to that of uncoated specimen. The phase analysis revealed the presence of Cr₂O₃ and ZrO₂ phases in composite coating matrix, which may have prevented the base metal from interacting with the corrosive elements present in the highly aggressive environment and thus had increased the resistance to hot corrosion.

It should be mentioned here that high temperature corrosion behaviour of thermally sprayed ZrO₂–Cr₂O₃ composite coatings has never been studied, and to the best of the authors’ knowledge, it is not available in the literature. Hence, present investigation can provide valuable information for application of ZrO₂-reinforced coatings in high temperature fuel combustion environments.

This study aims to investigate the effect of electrodeposition parameters (i.e. time and voltage) on the properties of hydroxyapatite (HA) coating fabricated on Ti6Al4V surface.

A full factorial design along with response surface methodology was utilized to evaluate the main effect of independent variables and their relative interactions on response variables. The effect of electrodeposition voltage and deposition time on HA coatings Ca/P molar ratio and the size of deposited HA crystals were examined by structural equation modeling (SEM). The formation of plate-like and needle-like HA crystals was observed for all experiments.

The results obtained showed that the higher electrodeposition voltage leads to lower Ca/P values for HA coatings. This is more significant at lower deposition times, where at a 20-minute deposition time, the voltage increased from 2 to 3 V and the Ca/P decreased from 2.27 to 1.52. Full factorial design results showed that electrodeposition voltage has a more significant effect on the size of the deposited HA crystal. With increasing the voltage from 2 to 3 V at a deposition time of 20 min, the HA crystal size varied from 99 to 36 µm.

The investigation delved into the impact of two critical parameters, deposition time and voltage, within the electrodeposition process on two paramount properties of HA coatings. Analyzing the alterations in coating characteristics relative to variations in these process parameters can serve as a foundational guide for subsequent research in the domain of calcium-phosphate deposition for implants.