Search results

The purpose of this paper is to study the effect of nano alumina (Al₂O₃) on the properties of fresh concrete, hardened concrete and microstructure of concrete incorporated with high range water reducer (HRWR). This initiative was taken to improve characteristic properties of concrete using nano alumina because nano alumina can be easily be manufactured from a scrap of industrial aluminum products, so its incorporation in concrete will not only reduce industrial aluminum waste but will also change the morphology of concrete at the microstructural level.

To accomplish the objectives of the research, four different concrete mixes with the constant water–cement ratio (W/C) and superplasticizer (SP) content 0.4 and 0.6% by weight of cement, respectively, were prepared, whereas nano alumina content was altered by 0.3% and 0.4% by weight of cement. Fresh property of concrete was analyzed by using slump cone test, whereas hardened properties of concrete were analyzed through compression test and flexural strength test. The interaction of nano alumina with concrete composite was evaluated using an X-ray diffraction test.

It was observed that 0.6% superplasticizer by weight of cement increased workability by 22% but with the addition of 0.3%, nano alumina by weight of cement workability decreased by 31%. Compressive strength increased by 4.88% with the addition of 0.6% superplasticizer but with the addition of 0.3% nano alumina by weight of cement compressive strength increased by 18.60%. Also, flexural strength increased by 1.21% with the addition of 0.6% superplasticizer by weight of cement but with the addition of 0.3% nano alumina by weight of cement flexural strength increased by 8.76%. With the addition of superplasticizer, alite and belite phases remained un-hydrated but with the addition of nano alumina alite phase was hydrated while belite phase was un-hydrated. The size of belite crystals in mixes having nano alumina was less than that of mix having 0.6% superplasticizer. Also with the addition of nano alumina, a calcium aluminum silicate phase was formed which was responsible for the increment of strength in mixes having nano alumina.

Incorporation nano alumina (Al₂O₃) in concrete will not only reduce industrial aluminum waste but will also reduce CO₂ emission. Nano alumina (Al₂O₃) also changes morphology of concrete at micro structural level.

This study aims to assess the efficacy of nano-alumina (nano-Al₂O₃) in improving the performance of epoxy adhesives used to assemble archaeological glass. The conservators face a significant problem in assembling this type of artifact. Therefore, the assembling process is considered one of the important stages that must be taken care of to preserve these artifacts from damage and loss.

To evaluate the stability of adhesives, the samples were subjected to artificial aging under varying environmental conditions. Some investigative techniques and mechanical testing were used in this study to evaluate the selected materials. It includes a transmission electron microscope, X-ray diffraction, visual assessment, digital microscope, scanning electron microscopy (SEM), color change and tensile strength test.

The visual evaluation and the digital microscope results showed that the epoxy/nano-Al₂O₃ greatly resisted artificial aging. Although slight yellowing was present, it did not significantly affect the general appearance of the samples. On the other hand, the pure epoxy sample showed cracks of different sizes on its surface due to aging, as evidenced by SEM examination. Furthermore, epoxy/nano-Al₂O₃ has a better tensile strength (11.27 MPa) and slight color change (ΔE = 2.06).

The main objective of the experimental study was to identify appropriate adhesive materials that possess key properties such as non-yellowing and improved tensile strength by conducting various tests and evaluations. Ultimately, the goal was to identify materials that could serve as effective adhesives for assembling the archaeological glass.

The purpose of this paper is to fabricate the scaffolds with different pore architectures using additive manufacturing and analyze its mechanical and biological properties for bone tissue engineering applications.

The polylactic acid (PLA)/composite filament were fabricated through single screw extrusion and scaffolds were printed with four different pore architectures, i.e. circle, square, triangle and parallelogram with fused deposition modelling. Afterwards, scaffolds were coated with hydroxyapatite (HA) using dip coating technique. Various physical and thermo-mechanical tests have been conducted to confirm the feasibility. Furthermore, the biological tests were conducted with MG63 fibroblast cell lines to investigate the biocompatibility of the developed scaffolds.

The scaffolds were successfully printed with different pore architectures. The pore size of the scaffolds was found to be nearly 1,500 µm, and porosity varied between 53% and 63%. The fabricated circular pore architecture resulted in highest average compression strength of 13.7 MPa and modulus of 525 MPa. The characterizations showed the fidelity of the work. After seven days of cell culture, it was observed that the developed composites were non-toxic and supported cellular activities. The coating of HA made the scaffolds bioactive, showing higher wettability, degradation and high cellular responses.

The research attempts highlight the development of novel biodegradable and biocompatible polymer (PLA)/bioactive ceramic (Al₂O₃) composite for additive manufacturing with application in the tissue engineering field.

The purpose of this study is to do a numerical analysis of the jet to a body filled with phase change material (PCM). The melting of the PCM filled body was investigated by the hot jet flow. Four different values of the Reynolds number were taken, ranging from 5 × 103 = Re = 12.5 103. Water, Al₂O₃ 1%, Al₂O₃ 2% and hybrid nanofluid (HNF; Al₂O₃–Ag mixture) were used as fluid types and the effects of fluid type on melting were investigated. At 60 °C, the jet stream was impinged on the PCM filled body at different Reynolds numbers.

Two-dimensional analysis of melting of PCM inserted A block via impinging turbulent slot jet is numerically studied. Governing equations for turbulent flow are solved by using the finite element method via analysis and system fluent R2020.

The obtained results showed that the best melting occurred when the Reynolds number increased and the HNF was used. However, the impacts of using alumina-water nanofluid were slight. At Re = 12,500, phase completion time was reduced by about 13.77% when HNF was used while this was only 3.93% with water + alumina nanofluid as compared to using only water at Re = 5,000. In future studies, HNF concentrations will change the type of nanoenhanced PCMs. In addition, the geometry and jet parameters of the PCM-filled cube can be changed.

Effects of impinging jet onto PCM filled block and control of melting via impinging hot jet of PCM. Thus, novelty of the work is to control of melting in a block by impinging hot jet and nanoparticles.

The evaluation of the haptics of water taps and wear-related changes during usage usually involves time- and cost-intensive testing. The purpose of this paper is to abstract the tribo-system between technical ceramic disks of water tap mixer cartridges to the model level and study the tribological behavior.

The friction and wear behavior was studied by means of an alumina ball-on-original alumina disk setup at different temperatures as well as under dry conditions and under lubrication by different greases. Thereby, the frictional behavior was measured in situ, and the wear losses were analyzed by means of laser scanning microscopy.

It was shown that friction and wear can behave in a contrasting way, whereby one grease might lead to low friction, that is, an easy-going movability of the water tap, but to increased wear losses. The latter, in turn, is an indicator for the usability and service life, which cannot be explained from friction alone. Thereby, the viscosity of the base oil, the grease consistency and additives were identified as relevant grease formulation parameters to allow for fluid film (re-)formation and removal of wear particles.

To the authors’ best knowledge, this is the first approach to systematically analyze the friction and wear behavior of technical ceramic disks of water tap mixer cartridges in dependency on the temperature as well as the used lubricating grease. This approach is relevant for developing screening test strategies as well as for the selection of lubricants for water tap applications.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2022-0334/

FeNi36 (Invar-36) alloy is widely used in the fabrication of molding tools in aerospace industries but there remains a need to improve its wear and friction performance due to its relatively low hardness. The formation of a heat affected zone (HAZ) on the surface of Invar-36 cut by wire electric discharge machining (WEDM) is promising to enhance its tribological properties. This study aims to investigate the tribological performance of WEDM-treated Invar-36 via a ball-on-disk tribometer in dry-sliding conditions.

The untreated and WEDM-treated Invar-36 surfaces were reciprocated against an alumina ball at a sliding velocity of 40 mm/s, a stroke length of 10 mm and a sliding duration of 125 min under loads of 5, 10 and 20 N. The worn surfaces were characterized using a 2D profilometry and a scanning electron microscope equipped with energy-dispersive spectroscopy.

The results showed that the WEDM-treated surface had a superior friction coefficient and wear resistance in comparison to the untreated surface, due to the grown HAZ. There was found to be a 9.3%–11.4% decrease in the friction coefficient and a 47%–57% reduction in the wear volume after the WEDM treatment. Both the untreated and WEDM-treated Invar-36 surfaces found abrasion and plastic deformation as the dominant wear mechanisms.

Previous works have not focused on the tribological performance of the WEDM-treated Invar-36 extensively used for molding tools in aerospace industries. Our findings provide compelling evidence that the WEDM treatment improved the wear and friction performance of Invar-36 alloy because of the grown HAZ.

This paper aims to provide a critical review of water generation from atmospheric air by using desiccant materials. Over the past few years, there has been very high stress on water scarcity, especially in Asian and African countries. Because of this insecurity, many countries are focusing on their research in the field of water technologies. Water generation from atmospheric air by using desiccant materials is one of the techniques among the air-to-water generators (AWGs).

A structured and systematic literature review has been presented to observe and understand the past trend/patterns in the field of water generation from atmospheric air by using desiccant materials. To understand the water generation technologies based on desiccant materials, the research papers from the years 1987 to 2022 have been studied and included.

The properties of the different and most probable desiccant materials in the field of AWGs have been discussed. A detailed review of testing reports of collected water samples has also been presented in tabular form. Finally, the economic analysis has been done and future prospects have been discussed. It is also found that the capacity of solid desiccant materials to adsorb the water is less as compared to liquid desiccant materials. But, the adsorption capacity can be improved by using composite desiccant materials.

The uniqueness of this manuscript lies in the compiling and examination of the existed published research papers, including variables such as author, year and geographical location, experimental/simulative, types of desiccant material, type of setup, desiccant material type and quantity and type of concentrator. This manuscript provides critique to the empirical and conceptual research in AWG technologies and also stimulates researchers to explore the topic very carefully.

This paper aims to investigate the hydrodynamic instability properties of a mixed convection flow of nanofluid in a porous channel.

The treated single-phase nanofluid is a suspension consisting of water as the working fluid and alumina as a nanoparticle. The anisotropy of the porous medium and the effects of the inclination of the magnetic field are highlighted. The effects of viscous dissipation and thermal radiation are incorporated into the energy equation. The eigenvalue equation system resulting from the stability analysis is processed numerically by the spectral collocation method.

Analysis of the results in terms of growth rate reveals that increasing the volume fraction of nanoparticles increases the critical Reynolds number. Parameters such as the mechanical anisotropy parameter and Richardson number have a destabilizing effect. The Hartmann number, permeability parameter, magnetic field inclination, Prandtl number, wave number and thermal radiation parameter showed a stabilizing effect. The Eckert number has a negligible effect on the growth rate of the disturbances.

Linear stability analysis of Magnetohydrodynamics (MHD) mixed convection flow of a radiating nanofluid in porous channel in presence of viscous dissipation.

Inclination angle has been reported to have an enhancing effect on the thermal-hydraulic characteristics and entropy of some thermal systems. Therefore, this paper aims to numerically investigate the effects of inclination angle, volume concentration and Reynolds number on the thermal and hydraulic characteristics and entropy generation rates of water-based Al₂O₃ nanofluids through a smooth circular aluminum pipe in a turbulent flow.

A constant heat flux of 2,000 Watts is applied to the circular surface of the tube. Reynolds number is varied between 4,000 and 20,000 for different volume concentrations of alumina nanoparticles of 0.5%, 1.0% and 2.0% for tube inclination angles of ±90o, ±60o, ±45o, ±30o and 0o, respectively. The simulation is performed in an ANSYS Fluent environment using the realizable kinetic energy–epsilon turbulent model.

Results show that +45o tube orientation possesses the largest thermal deviations of 0.006% for 0.5% and 1.0% vol. concentrations for Reynolds numbers 4,000 and 12,000. −45o gives a maximum pressure deviation of −0.06% for the same condition. The heat transfer coefficient and pressure drop give maximum deviations of −0.35% and −0.39%, respectively, for 2.0% vol. concentration for Reynolds number of 20,000 and angle ±90o. A 95%–99.8% and 95%–98% increase in the heat transfer and total entropy generation rates, respectively, is observed for 2.0% volume concentration as tube orientation changes from the horizontal position upward or downward.

Research investigating the effect of inclination angle on thermal-hydraulic performance and entropy generation rates in-tube turbulent flow of nanofluid is very scarce in the literature.