Search results

The purpose of this study is to numerically investigate the effect of jet impingement, magnetic field and nanoparticle shape (sphericity) on the hydrodynamic/heat transfer characteristics of nanofluids over stationary and vibrating plates.

A two-dimensional finite volume method-based homogeneous heat transfer model has been developed, validated and used in the present investigation. Three different shapes of non-spherical carbon nanoparticles namely nanotubes, nanorods and nanosheets are used in the analysis. Sphericity-based effective thermal conductivity of nanofluids with Brownian motion of nanoparticles is considered in the investigation. Moreover, the ranges of various comprehensive parameters used in the study are Re = 500 to 900, St = 0.0694 to 0.2083 and Ha = 0 to 80.

The hydrodynamic/heat transfer performance of jet impingement in the case of vibrating plate is 298 per cent higher than that of stationary plate at Re = 500. However, for the case of vibrating plate, a reduction in the heat transfer performance of 23.35 per cent is observed by increasing the jet Reynolds number from 500 to 900. In the case of vibrating plate, the saturation point for Strouhal number is found to be 0.0833 at Re = 900 and Ha = 0. Further decrement in St beyond this limit leads to a drastic reduction in the performance. Moreover, no recirculation in the flow is observed near the stagnation point for jet impingement over vibrating plate. It is also observed that the effect of magnetic field enhances the performance of jet impingement over a stationary plate by 36.18 per cent at Ha = 80 and Re = 900. Whereas, opposite trend is observed for the case of vibrating plate. Furthermore, at Re = 500, the percentage enhancement in the Nuavg values of 3 Vol.% carbon nanofluid with nanosheets, nanorods and nanotubes are found to be 47.53, 26.86 and 26.85 per cent when compared with the value obtained for pure water.

The present results will be useful in choosing nanosheets-based nanofluid as the efficient heat transfer medium in cooling of high power electronic devices. Moreover, the obtained saturation point in the Strouhal number of the vibrating plate will help in cooling of turbine blades, as well as paper and textile drying. Moreover, the developed homogeneous heat transfer model can also be used to study different micro-convection phenomena in nanofluids by considering them as source terms in the momentum equation.

Impingement of jet over two different plate types such as stationary and vibrating is completely analyzed with the use of a validated in-house FVM code. A complete investigation on the influence of external magnetic field on the performance of plate type configuration is evaluated. The three fundamental shapes of carbon nanoparticles are also evaluated to obtain sphericity based hydrodynamic/heat transfer performance of jet impingement.

The purpose of this study is to examine the physical processes experienced by a particle-laden gas due to various types of collisions, different heat transfer modalities and jet axis switching. Here, attention is focused on a particle-laden gas subjected to jet axis switching while experiencing fluid flow and heat transfer.

The methodology used to model and solve these complex problems is numerical simulation treated here as a two-phase turbulent flow in which the gas and the particles keep their separate identities. For the turbulent flow model, validation was achieved by comparisons with appropriate experimental data. The considered interactions between the fluid and the particles include one-way fluid–particle interactions, two-way fluid–particle interactions and particle–particle interactions.

For the fluid flow portion of the work, emphasis was placed on the particle collection efficiency and on independent variables that affect this quantity and the trajectories of the fluid and of the particles as they traverse the space between the jet orifice and the impingement plate. The extent of the effect depended on four factors: particle size, particle density, number of particles and the velocity of the fluid flow. The major effect on the heat transferred to the impingement plate occurred when direct heat transfer between the impinging particles and the plate was taken into account.

This paper deals with issues never before dealt with in the published literature: the effect of jet axis switching on the fluid mechanics of gas-particle flows without heat transfer and the effect of jet axis switching and the presence of particles on jet impingement heat transfer. The overall focus of the work is on the impact of jet axis switching on particle-laden fluid flow and heat transfer.

Convective heat transfer features of a turbulent slot jet impingement are comprehensively studied using two different computational approaches, namely, URANS (unsteady Reynolds-averaged Navier–Stokes equations) and SAS (scale-adaptive simulation). Turbulent slot jet impingement heat transfer is used where a considerable heat transfer enhancement is required, and computationally, it is a quite challenging flow configuration.

Customized OpenFOAM 4.1, an open-access computational fluid dynamics (CFD) code, is used for SAS (SST-SAS k-ω) and URANS (standard k-ε and SST k-ω) computations. A low-Re version of the standard k-ε model is used, and other models are formulated for good wall-refined calculations. Three turbulence models are formulated in OpenFOAM 4.1 with second-order accurate discretization schemes.

It is observed that the profiles of the streamwise turbulence are under-predicted at all the streamwise locations by SST k-ω and SST SAS k-ω models, but follow similar trends as in the reported results. The standard k-ε model shows improvements in the predictions of the streamwise turbulence and mean streamwise velocity profiles in the zone of outer wall jet. Computed profiles of Nusselt number by SST k-ω and SST-SAS k-ω models are nearly identical and match well with the reported experimental results. However, the standard k-ε model does not provide a reasonable profile or quantification of the local Nusselt number.

Hybrid turbulence model is suitable for efficient CFD computations for the complex flow problems. This paper deals with a detailed comparison of the SAS model with URANS and LES for the first time in the literature. A thorough assessment of the computations is performed against the results reported using experimental and large eddy simulations techniques followed by a detailed discussion on flow physics. The present results are beneficial for scientists working with hybrid turbulence models and in industries working with high-efficiency cooling/heating system computations.

This study aims to focus on the surface curvature, jet to target spacing and jet Reynolds number effects on the heat transfer and fluid flow characteristics of a slot jet impinging on a confined concave target surface at constant jet to target spacing.

Numerical simulations are used in this research. Jet to target spacing, H/B is varying from 1.0 to 2.2, B is the slot width. The jet Reynolds number, Rej, varies from 8,000 to 40,000, and the surface curvature, R2/B, varies from 4 to 20. Results of the target surface heat transfer, flow parameters and fluid flow in the concave channel are performed.

It is found that an obvious backflow occurs near the upper wall. Both the local and averaged Nusselt numbers considered in the defined region respond positively to the Rej. The surface curvature plays a positive role in increasing the averaged Nusselt number for smaller surface curvature (4-15) but affects little as the surface curvature is large enough (> 15). The thermal performance is larger for smaller surface curvature and changes little as the surface curvature is larger than 15. The jet to target spacing shows a negative effect in heat transfer enhancement and thermal performance.

The surface curvature effects are conducted by verifying the concave surface with constant jet size. The flow characteristics are first obtained for the confined impingement cases. Then confined and unconfined slot jet impingements are compared. An ineffective point for surface curvature effects on heat transfer and thermal performance is obtained.

Numerical simulations are performed to determine the heat transfer characteristics of slot jet impingement of air on a concave surface. The purpose of this paper is to investigate the effect of protrusions on the heat transfer by placing semi-circular protrusions on the concave surface at several positions. After identifying appropriate locations where the heat transfer is a maximum, multiple protrusions are placed at desired locations on the plate. The gap ratio, curvature ratio (d/D) and the dimensions of the plate are varied so as to obtain heat transfer data. The curvature ratio is varied first, keeping the concave diameter (D) fixed followed by a fixed slot width (d). A surrogate model based on an artificial neural network is developed to determine optimum locations of the protrusions that maximize the heat transfer from the concave surface.

The scope and objectives of the present study are two-dimensional numerical simulations of the problem by considering all the geometrical parameters (H/d, d_p, Re, θ) affecting heat transfer characteristics with the help of networking tool and numerical simulation. Development of a surrogate forward model with artificial neural networks (ANNs) with a view to explore the full parametric space. To quantitatively ascertain if protrusions hurt or help heat transfer for an impinging jet on a concave surface. Determination of the location of protrusions where higher heat transfer could be achieved by using exhaustive search with the surrogate model to replace the time consuming forward model.

A single protrusion has nearly no effect on the heat transfer. For a fixed diameter of concave surface, a smaller jet possesses high turbulence kinetic energy with greater heat transfer. ANN is a powerful tool to not only predict impingement heat transfer characteristics by considering multiple parameters but also to determine the optimum configuration from many thousands of candidate solutions. A maximum increase of 8 per cent in the heat transfer is obtained by the best configuration constituting of multiple protrusions, with respect to the baseline smooth configuration. Even this can be considered as marginal and so it can be concluded that first cut results for heat transfer for an impinging jet on a concave surface with protrusions can be obtained by geometrically modeling a much simpler plain concave surface without any significant loss of accuracy.

The heat transfer during impingement cooling depends on various geometrical parameters but, not all the pertinent parameters have been varied comprehensively in previous studies. It is known that a rough surface may improve or degrade the amount of heat transfer depending on their geometrical dimensions of the target and the rough geometry and the flow conditions. Furthermore, to the best of authors’ knowledge, scarce studies are available with inclusion of protrusions over a concave surface. The present study is devoted to development of a surrogate forward model with ANNs with a view to explore the full parametric space.

The purpose of this study is to investigate the effects of film holes’ arrangements and jet Reynolds number on flow structure and heat transfer characteristics of jet impingement conjugated with film cooling in a semicylinder double wall channel.

Numerical simulations are used in this research. Streamlines on different sections, skin-friction lines, velocity, wall shear stress and turbulent kinetic energy contours near the concave target wall and vortices in the double channel are presented. Local Nusselt number contours and surface averaged Nusselt numbers are also obtained. Topology analysis is applied to further understand the fluid flow and is used in analyzing the heat transfer characteristics.

It is found that the arrangement of side films positioned far from the center jets helps to enhance the flow disturbance and heat transfer behind the film holes. The heat transfer uniformity for the case of 55° films arrangement angle is most improved and the thermal performance is the highest in this study.

The film holes’ arrangements effects on fluid flow and heat transfer in an impingement cooled concave channel are conducted. The flow structures in the channel and flow characteristics near target by topology pictures are first obtained for the confined film cooled impingement cases. The heat transfer distributions are analyzed with the flow characteristics. The highest heat transfer uniformity and thermal performance situation is obtained in present work.

The purpose of this paper is to explore the flow and heat transfer characteristics of the jet impingement onto a conical heat sink and evaluate the ability of heat transfer enhancement.

A numerical study of the flow and heat transfer of liquid impingement on cone heat sinks was conducted, and transition SST turbulence model was validated and adopted. The flow and thermal performances were investigated with the Reynolds number that ranges from 5,000 to 23,000 and cone angle that ranges from 0° to 70° in four regions.

Local Nusselt numbers are large, and pressure coefficients drop rapidly near the stagnation point. In the conical bottom edge, a secondary inclined jet was observed, thereby introducing a horseshoe vortex that causes drastic fluctuations in the curves of the flow and heat transfer. The average Nusselt numbers are higher in a conical protuberance than in flat plates in most cases, thus indicating that the heat transfer performance of jet impingement can be improved by a cone heat sink. The maximum increase is 13.6 per cent when the cone angle is 60°, and the Reynolds number is 23,000.

The flow and heat transfer behavior at the bottom edge of the cone heat sink is supplemented. The average heat transfer capacity of different heat transfer radii was evaluated, which provided a basis for the study of cone arrays.

The dimple is adopted into a double wall cooling structure which is widely used in hot gas components to increase the heat transfer effects with relatively low pressure drop penalty. The purpose of this paper is to study the effect of dimple depth and dimple diameter on the target surface heat transfer and the inlet to outlet friction factor.

The study is carried out by using the numerical simulations. The impingement flow is directly impinging on the dimple and released from the film holes after passing the double wall chamber. The ratio between dimple depth and dimple diameter is varied from 0 to 0.4 and the ratio between dimple diameter and impingement hole diameter is ranging from 0.5 to 3. The Reynolds number is between 10,000 and 70,000. Results of the target surface Nusselt number, friction factor and flow structures are included. For convenience of comparison, the double wall cooling structure without the dimple is considered as the baseline.

It is found that the dimple can effectively enhance the target surface heat transfer due to thinning of the flow boundary layer and flow reattachment as well as flow recirculation outside the dimple near the dimple rim especially for the large Re number condition. However, the stagnation point heat transfer is reduced. It is also found that for a large dimple depth or large dimple diameter, a salient heat transfer reduction occurs for the toroidal vortex. The thermal performance indicates that the intensity of the heat transfer enhancement depends upon the dimple depth and dimple diameter

This is the first time to adopt a dimple into a double wall cooling structure. It suggests that the target surface heat transfer in a double wall cooling structure can be increased by the use of the dimple. However, the heat transfer characteristic is sensitive for the different dimple diameter and dimple depth which may result in a different flow behavior

The purpose of this study is to perform computational analysis on the steady flow and heat transfer due to a slot nanojet impingement onto a heated moving body. The object is moving at constant speed and nanoparticle is included in the heat transfer fluid. The unsteady flow effects and interactions of multiple impinging jets are also considered.

The finite volume method was used as the solver in the numerical simulation. The movement of the hot body in the channel is also considered. Influence of various pertinent parameters such as Reynolds number, jet to target surface spacing and solid nanoparticle volume fraction on the convective heat transfer characteristics are numerically studied in the transient regime.

It is found that the flow field and heat transfer becomes very complicated due to the interaction of multiple impinging jets with the movement of the hot body in the channel. Higher heat transfer rates are achieved with higher values of Reynolds number while the inclusion of nanoparticles resulted in a small impact on flow friction. The middle jet was found to play an important role in the heat transfer behavior while jet and moving body temperatures become equal after t = 80.

Even though some studies exist for the application of jet impingement heat transfer for a moving plate, the configuration with a solid moving hot body on a moving belt under the impacts of unsteady flow effects and interactions of multiple impinging jets have never been considered. The results of the present study will be helpful in the design and optimization of various systems related to convective drying of products, metal processing industry, thermal management in electronic cooling and many other systems.

Maintaining the turbine blade’s temperature within the safety limit is challenging in high-pressure turbines. This paper aims to numerically present the conjugate heat transfer analysis of a novel approach to mini-channel embedded film-cooled flat plate.

Numerical simulations were performed at a steady state using SST k – ω turbulence model. Impingement and film cooling are classical approaches generally adopted for turbine blade analysis. The existing film cooling techniques were compared with the proposed design, where a mini-channel was constructed inside the solid plate. The impact of the blowing ratio (M), Biot number (Bi) and temperature ratio (TR) on overall cooling performance was also studied.

Overall cooling effectiveness was always shown to be higher for mini-channel embedded film-cooled plates. The effectiveness increases with increasing the blowing ratio from M = 0.3 to 0.7, then decreases with increasing blowing ratio (M = 1 and 1.4) due to lift-off conditions. The mini-channel embedded plate resulted in an approximately 21% increase in area-weighted average overall effectiveness at a blowing ratio of 0.7 and Bi = 1.605. The lower uniform temperature was also found for all blowing ratios at a low Biot number, where conduction heat transfer significantly impacts total cooling effectiveness.

To the best of the authors’ knowledge, this study presents a novel approach to improve the cooling performances of a film-cooled flat plate with better cooling uniformity by using embedded mini-channels. Despite the widespread application of microchannels and mini-channels in thermal and fluid flow analysis, the application of mini-channels for blade cooling is not explored in detail.