Search results

The purpose of this paper is to present optimally designed synchronous reluctance machine (SynRM) to demonstrate the feasibility of eliminating the use of rare earth permanent magnet (PM) in electric machine for vehicle traction applications.

A typical rare earth interior permanent magnet (IPM) machine is used as the benchmark to conduct the optimal design study. Based on the flux distribution, major changes are made to the rotor lamination design. Enhanced torque production and lower torque ripple are specifically targeted as the two main objectives of the proposed design approach.

As a result, the optimally designed SynRM can achieve performance very close to that of the benchmark PM machine with a potential for further improvement.

Discussions of IPM replacement by optimally designed SynRM in electrical and hybrid electrical vehicles are given in terms of performance and cost.

The purpose of this paper is to present the optimal design of a low-cost interior permanent magnet (IPM) alternating current (AC) motor. It examines the influence of the permanent magnet (PM) materials, and proposes a simple and practical method of optimizing the air-gap field to achieve sinusoidal back electromotive force (EMF), and to reduce the cogging torque.

IPM AC motors with different magnet materials and various topologies are comparatively studied. Finite element method (FEM) is used to predict the performances of these designs. Material costs and manufacture costs are both taken into account. Finally, an optimized design is prototyped and tested, validating the design considerations.

In an IPM AC motor, even if the rotor outer profile is round, the air-gap field distribution can be fined, while the cogging torque can be significantly reduced, by properly shaping the stator tooth tips. Nevertheless, this technique is usually applicable to motor configurations with concentrated windings, but not to those with distributed windings.

While using ferrite magnets for PM AC motors with a kW power, interior magnets are usually inserted in V-shaped slots, and the rotor outer profile is often shaped in order to enhance the air-gap field distribution. However, such a rotor configuration usually increases the manufacture costs, and also deteriorates the consistency of mass production. Therefore, a new motor configuration with a round rotor outer profile and shaped stator tooth tips is proposed. It can not only overcome the aforementioned problems, but also improve the motor performance.

In the past electromechanical actuators have been used to operate and control functions that demanded reasonably low power whilst the more arduous requirements of secondary and primary flying control surfaces have been powered by hydraulic motors and drives. With the advent of rare earth permanent magnet electrical machines with greatly enhanced magnetic properties allowing higher powers to be achieved without significant increases in mass and dimension, together with the development of high voltage power electronic devices, it is now possible to extend the application of electomechanical actuation even to primary flying control surfaces. This paper highlights some design aspects in the development of electromechanical actuators (EMA's), draws attention to the several advantages of EMA's and their rare earth drive motors and addresses some of the problems that need to be tackled in order to achieve full certification for future aircraft.

This study aims to propose criteria for both optimal-shape and magnetizer-system designs to be used for a high-output spoke-type motor. The study also examines methods of reducing high-cogging torque and torque ripple, to prevent noise and vibration.

The optimal design of the stator and rotor can be enhanced using both a response surface method (RSM) and finite element method (FEM). In addition, a magnetizer system is optimally designed for the magnetization of permanent magnets for use in the motor.

The criteria not only improve performance but also reduce manufacturing costs. The criteria are verified FEM together with an RSM. These methods are used to optimize the stator and rotor shape and the magnetization system. These methods allow us to produce an efficient system for mass production of the motor.

This study proposed a design method that uses rare earth magnets in a system to replace the spoke-type IPM. To verify the optimal design, torque characteristics were analysed using FEM and RSM. Excellent results were achieved regarding the reduction of cogging torque and torque ripple. In addition, the design of the magnetizer enables a cost-effective mass production system for the motor.

Reducing eddy current losses in magnets of electrical machines can be obtained by means of several techniques. The magnet segmentation is the most popular one. It imposes the least restrictions on machine performances. This paper investigates the effectiveness of the magnet circumferential segmentation technique to reduce these undesirable losses. The full and partial magnet segmentation are both studied for a frequency range from few Hz to a dozen of kHz. To increase the efficiency of these techniques to reduce losses for any working frequency, an optimization strategy based on coupling of finite elements analysis and genetic algorithm is applied. The purpose of this paper is to define the parameters of the total and partial segmentation that can ensure the best reduction of eddy current losses.

First, a model to analyze eddy current losses is presented. Second, the effectiveness of full and partial magnet circumferential segmentation to reduce eddy loss is studied for a range of frequencies from few Hz to a dozen of kHz. To achieve these purposes a 2-D finite element model is developed under MATLAB environment. In a third step of the work, an optimization process is applied to adjust the segmentation design parameters for best reduction of eddy current losses in case of surface mounted permanent magnets synchronous machine.

In case of the skin effect operating, both full and partial magnet segmentations can lead to eddy current losses increases. Such deviations of magnet segmentation techniques can be avoided by an appropriate choice of their design parameters.

Few works are dedicated to investigate partial magnet segmentation for eddy current losses reduction. This paper studied the effectiveness and behaviour of partial segmentation for different frequency ranges. To avoid eventual anomalies related to the skin effect an optimization process based on the association of the finite elements analysis to genetic algorithm method is adopted.

The purpose of this paper is to comparatively study the conventional, i.e. single magnet, and novel hybrid-magnet switched-flux permanent-magnet (HMSFPM) machines.

The HMSFPM machines utilize two magnet types, i.e. low-cost ferrites and NdFeB. Thus, a set of magnet ratios (?), defined as the quotient of the NdFeB volume to the total PM volume, is introduced. This allows any desired performance and cost trade-off to be designed. Series- and parallel-excited magnet configurations are investigated using 2-dimensional finite element analysis.

The torque of the HMSFPM machines is lower than the NdFeB SFPM machine but the flux-weakening performance is improved for similar machine efficiency. If the machine dimensions are unconstrained, the HMSFPM machines can have the same torque for reduced material costs and a moderate increase in machine dimensions. Ferrite SFPM machines have the lowest cost for the same torque but a significant increase in machine dimensions is required. Finally, the series-excited HMSFPM machine is the preferred over the parallel-excited HMSFPM machine because it has superior demagnetization withstand capability.

Mechanical and winding eddy current losses are not considered in the efficiency map calculations.

The NdFeB SFPM, ferrite SFPM, series-excited HMSFPM, and the parallel-excited HMSFPM machines are compared for their electromagnetic performance, flux-weakening, PM demagnetization, efficiency, and material costs.

Rare earths are essential materials for many high-tech industries critical to both economic development and national defense. China, the world's dominant supplier of rare earths, has recently been imposing stricter controls over its production and export. The purpose of this paper is to examine the domestic roots of the changes in China's rare earth industry production and exports in its three-decade rise to the current global monopoly.

This paper adopts the historical institutionalism approach to analyze the trajectory of industry and trade development. The author analyzes data collected from government whitepapers and reputed scholarly and news sources.

This paper argues that the Chinese rare earth industry has gone through three periods of development, in which the state attempted to control the market and industry through reformulating rules and institutions to achieve state goals. Domestic state institutions, combined with macroeconomic environment and state governance strategy shaped the three-decade experience of rare earth industry and trade development in China.

This paper builds on existing findings about Chinese state regulations to provide a novel analytical framework to analyze the role of the state in industry and trade development in the rare earth industry. The focus on a single strategic industry seldom studied in the current literature also provides ample empirical value to further scholarly understanding about this industry.

This paper demonstrates how the 3D edge element method can be applied to the analysis of permanent magnet motors. The edge element method using the vector magnetic potential has been used. Special attention has been paid to the analysis of systems with inhomogeneously magnetized permanent magnets. The magnets are not skewed and are mounted on a cylindrical laminated rotor. Calculations have been performed for different magnet widths and different distribution of the magnetization vector. Brushless motors with radially and inhomogeneously magnetized magnets have been compared.

The purpose of this paper is to solve the optimization problem for a permanent magnet linear actuator with moving magnet for driving a needle in a knitting machine. The optimization is carried out with respect to the maximal average force along the stroke.

The optimization factors are the dimensions of the permanent magnet and the pole length. For obtaining the objective function for each parameter combination, the static force‐stroke characteristic is computed. Three‐dimensional finite element analysis is employed for obtaining the electromagnetic force. The objective function is then approximated by secondary models on the basis of design of experiment. The optimization is carried out using sequential linear programming.

Optimal solution to the problem has been obtained and the force‐stroke characteristic of the optimal actuator is given.

The proposed approach employs sequential linear programming with move limits using trust region concept, 3D finite element analysis, design of experiments and secondary models for optimization of a permanent magnet linear actuator for individual needle driving in a knitting machine.

The purpose of this paper is to investigate the influence of stator and rotor pole number combinations together with the flux-barrier layers number on the performance of synchronous reluctance machine with emphasis on output torque capability and torque ripple.

AC synchronous reluctance machine (SynRM) or permanent magnet assisted SynRM presently receives a great deal of interest, since there is less or even no rare-earth permanent magnet in the rotor. Most of SynRM machines employ a stator that is originally designed for a standard squirrel cage induction motor for a similar output rating and application, or the SynRM machine with 24-slot, four-pole are often directly chosen for investigation in most of the available literature. Therefore, it is necessary to investigate the influence of stator and rotor pole number combinations together with the flux-barrier layers number on the performance of SynRM machine with emphasis on output torque capability and torque ripple.

The average torque decreases with the increase of the pole numbers but remain almost constant when employing different stator slot numbers but with the same pole number. In addition, the torque ripple decreases significantly with the increase of the stator slot number. The machine with double-layer flux-barrier in the rotor has the biggest average torque, while the machines with three- and four-layer flux-barrier in the rotor have almost the same average torque but their value is slightly smaller than that of machine with double-layer flux-barrier. However, the machine with three-layer flux-barrier has the lowest torque ripple but the highest torque ripple exists in the machine with double-layer flux-barrier.

The purely sinusoidal currents are applied in this analysis and the effects of harmonics in the current on torque ripple are not considered in this application.

This paper has analyzed the torque ripple and average torque of SynRMs with considering slot/pole number combinations together with the flux-barrier number.