Search results

The purpose of this research is to study the performance of piezoresistive pressure sensors using polysilicon as the piezoresistive material, which is typically used to measure pressure in high-temperature environments.

The performance of this sensor is enhanced by studying the influence of multi-turn configuration at which the piezoresistors are arranged. Different configurations are studied and compared by laying down their analytical solution.

The validation of analytical results is accomplished through finite element analysis using the software COMSOL Multiphysics. The best configuration, which uses a partial triple-turn configuration, was able to achieve a sensitivity of 116.00 mV/V/MPa over a simulated pressure range of 0 to 500 KPa.

The literature shows the study of single-turn and double-turn meander-shaped configuration of micro-electromechanical systems piezoresistive pressure sensor but multi-turn meander-shaped configuration using a square silicon diaphragm has not been reported. Its study has reflected promising results than its counterparts based on key performance parameters such as sensitivity and linearity and are more effective to be used for automotive, aviation, biomedical and consumer electronics applications.

Material extrusion-based additive manufacturing is a prominent manufacturing technique to fabricate complex geometrical three-dimensional (3D) parts. Despite the indisputable advantages of material extrusion-based technique, the poor surface and subsurface integrity hinder the industrial application of this technology. The purpose of this study is introducing the hot air jet treatment (HAJ) technique for surface treatment of additive manufactured parts.

In the presented research, novel theoretical formulation and finite element models are developed to study and model the polishing mechanism of printed parts surface through the HAJ technique. The model correlates reflow material volume, layer width and layer height. The reflow material volume is a function of treatment temperature, treatment velocity and HAJ velocity. The values of reflow material volume are obtained through the finite element modeling model due to the complexity of the interactions between thermal and mechanical phenomena. The theoretical model presumptions are validated through experiments, and the results show that the treatment parameters have a significant impact on the surface characteristics, hardness and dimensional variations of the treated surface.

The results demonstrate that the average value of error between the calculated theoretical results and experimental results is 14.3%. Meanwhile, the 3D plots of Ra and Rq revealed that the maximum values of Ra and Rq reduction percentages at 255°C, 270°C, 285°C and 300°C treatment temperatures are (35.9%, 33.9%), (77.6%,76.4%), (94%, 93.8%) and (85.1%, 84%), respectively. The scanning electron microscope results illustrate three different treatment zones and the treatment-induced and manufacturing-induced entrapped air relief phenomenon. The measured results of hardness variation percentages and dimensional deviation percentages at different regimes are (8.33%, 0.19%), (10.55%, 0.31%) and (−0.27%, 0.34%), respectively.

While some studies have investigated the effect of the HAJ process on the structural integrity of manufactured items, there is a dearth of research on the underlying treatment mechanism, the integrity of the treated surface and the subsurface characteristics of the treated surface.

Hydraulic slide valve failure often results from competing failure modes, termed competitive failure. To enhance prediction accuracy for hydraulic slide valve remaining useful life, the authors propose a method incorporating competitive failure and Monte Carlo simulation. This method allows for more accurate prediction of hydraulic slide valve remaining useful life.

In this paper, the competitive failure mode of the hydraulic slide valve is analyzed by studying the two failure modes of the hydraulic slide valve, and the prediction of the remaining useful life of the hydraulic slide valve is studied by using the sample set generated by Monte Carlo simulation and the competitive failure joint model.

The results show that the proposed prediction method based on competitive failure and Monte Carlo simulation is more accurate than the traditional Bayesian joint model prediction method when dealing with the failure mode competition phenomenon of hydraulic slide valve.

In this paper, the remaining useful life prediction of hydraulic slide valve with competitive failure characteristics is studied, which provides a new idea for the remaining useful life prediction method.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2023-0361/

The purpose of this study is to investigate whether and how inter-firm cooperation and firm age moderate the relationship between family ownership and productivity.

We first estimate the total factor productivity (TFP) of a large sample of Italian firms observed over the period 2010–2018 and then apply a Poisson random effects model.

TFP is, on average, higher for non-family firms (non-FFs) than for FF. Furthermore, inter-organizational cooperation and firm age mitigate the negative effect of family ownership. In detail, it is found that belonging to a network acts as a moderator in different ways according to firm age. Indeed, young FFs underperform non-FF peers, although the TFP gap decreases with age. In contrast, the benefits of a formal network are high for older FFs, suggesting that an age-related learning process is at work.

The study provides evidence that FFs can outperform non-FFs when they move away from Socio-Emotional Wealth-centered reference points and exploit knowledge flows arising from high levels of social capital. In the case of mature FFs, networking is a driver of TFP, allowing them to acquire external resources. Since FFs often do not have sufficient in-house knowledge and resources, they must be aware of the value of business cooperation. While preserving the familiar identity of small companies, networks grant FFs the competitive and scale advantages of being large.

Despite the wide but ambiguous body of research on the performance gap between FFs and non-FFs, little is known about the role of FFs’ heterogeneity. This study has proven successful in detecting age as a factor in heterogeneity, specifically to explain the network effect on the link between ownership and TFP. Based on a representative sample, the study provides a solid framework for FFs, policymakers and academic research on family-owned companies.

Wire-arc-based additive manufacturing (WAAM) is a promising technology for the efficient and economical fabrication of medium-large components. However, the anisotropic behavior of the multilayered WAAM-fabricated components remains a challenging problem.

The purpose of this paper is to conduct a comprehensive study of the grain morphology, crystallographic orientation and texture in three regions of the WAAM printed component. Furthermore, the interdependence of the grain morphology in different regions of the fabricated component with their mechanical and tribological properties was established.

The electron back-scattered diffraction analysis of the top and bottom regions revealed fine recrystallized grains, whereas the middle regions acquired columnar grains with an average size of approximately 8.980 µm. The analysis revealed a higher misorientation angle and an intense crystallographic texture in the upper and lower regions. The investigations found a higher microhardness value of 168.93 ± 1.71 HV with superior wear resistance in the bottom region. The quantitative evaluation of the residual stress detected higher compressive stress in the upper regions. Evidence for comparable ultimate tensile strength and greater elongation (%) compared to its wrought counterpart has been observed.

The study found a good correlation between the grain morphology in different regions of the WAAM-fabricated component and their mechanical and wear properties. The Hall–Petch relationship also established good agreement between the grain morphology and tensile test results. Improved ductility compared to its wrought counterpart was observed. The anisotropy exists with improved mechanical properties along the longitudinal direction. Moreover, cylindrical components have superior tribological properties compared with cuboidal components.

Concrete-filled double skin tube (CFDST) columns are considered one of the most effective steel-concrete composite sections owing to the higher load carrying capacity as compared to its counterpart concrete-filled tube (CFT) columns. This paper aims to numerically investigate the performance of axially loaded, circular CFDST short columns, with the innovative strengthening technique of providing stiffeners in outer tubes. Circular steel hollow sections have been adopted for inner as well as outer tubes, while varying the length of rectangular steel stiffeners, fixed inside the outer tubes only, to check the effect of stiffeners in partially and full-length stiffened CFDST columns.

The behaviour of these CFDST columns is investigated numerically by using a verified finite element analysis (FEA) model from the ABAQUS. The behaviour of 20-unstiffened, 80-partially stiffened and 20-full-length stiffened CFDST columns is studied, while varying the strength of steel (f_yo = 250–750 MPa) and concrete (30–90 MPa).

The FEA results are verified by comparing them with the previous test results. FEA study has exhibited that, there is a 7%–25% and 39%–49% increase in peak-loads in partially stiffened and full-length stiffened CFDST columns, respectively, compared to unstiffened CFDST columns.

Enhanced strength has been observed in partially stiffened and full-length stiffened CFDST columns as compared to unstiffened CFDST columns. Also, a significant effect of strength of concrete has not been observed as compared to the strength of steel.

Given the relevance of female directors in the governance of any firm, this paper aims to examine their effect on firms’ financial performance by investigating their general impact and segregating the same into different subgroups based on Kanter’s theory.

To achieve the purpose, this study selects a sample of the top 100 listed Indian firms for the period of 2014–2018 and gathers the data pertaining to the variables under consideration from the respective firms’ annual report and corporate database Capitaline Plus. For undertaking the investigation, the authors have segregated the sample into three groups, i.e. firms with boards having less than 10% of female directors are called skewed boards; firms with boards having female directors that range from 10% to 20% are called as tilted board; and firms with boards having sizable representation of female directors of above 20%. To examine the performance impact of overall female directors and their different subgroups, the authors have used a generalized estimating equation model. For the robustness test, the authors have used the fixed-effect model.

The authors find a significant positive impact of the overall percentage of female directors on the financial performance of firms. Additionally, the results indicate that boards with a titled group of female directors and boards with a sizable representation of female directors significantly positively impact firms’ performance. However, the authors fail to extricate any significant performance impact of boards with a skewed group of female directors.

First, the study reveals that despite prevailing nepotism in India, female directors, owing to their core characteristics, can create a favorable perception of firms in the market. Second, it also works as an eye-opener for regulators by revealing the minimum threshold for female directors that a board should have to exploit the benefits of a gender quota rather than mere compliance with the requirements of the Companies Act, 2013. Third, it implies that more gender-diverse boards can improve a firm’s financial performance only if female directors range between the thresholds of 10% to 20%. Finally, the finding is significant for changing the business culture in India, where institutions are traditionally less supportive of women than in other emerging countries.

Departing from existing studies, which provide evidence on the performance impact of the overall percentage of female directors, the study unveils the differential impact of female directors on firms’ financial performance depending on their level of representation on the board. To the best of the authors’ knowledge, this is the first study in the context of an emerging market to test Kanter’s theory.

This study aims to investigate the thermal fracture mechanism of moisture-preconditioned SAC305 ball grid array (BGA) solder joints subjected to multiple reflow and thermal cycling.

The BGA package samples are subjected to JEDEC Level 1 accelerated moisture treatment (85 °C/85%RH/168 h) with five times reflow at 270 °C. This is followed by multiple thermal cycling from 0 °C to 100 °C for 40 min per cycle, per IPC-7351B standards. For fracture investigation, the cross-sections of the samples are examined and analysed using the dye-and-pry technique and backscattered scanning electron microscopy. The packages' microstructures are characterized using an energy-dispersive X-ray spectroscopy approach. Also, the package assembly is investigated using the Darveaux numerical simulation method.

The study found that critical strain density is exhibited at the component pad/solder interface of the solder joint located at the most distant point from the axes of symmetry of the package assembly. The fracture mechanism is a crack fracture formed at the solder's exterior edges and grows across the joint's transverse section. It was established that Au content in the formed intermetallic compound greatly impacts fracture growth in the solder joint interface, with a composition above 5 Wt.% Au regarded as an unsafe level for reliability. The elongation of the crack is aided by the brittle nature of the Au-Sn interface through which the crack propagates. It is inferred that refining the solder matrix elemental compound can strengthen and improve the reliability of solder joints.

Inspection lead time and additional manufacturing expenses spent on investigating reliability issues in BGA solder joints can be reduced using the study's findings on understanding the solder joint fracture mechanism.

Limited studies exist on the thermal fracture mechanism of moisture-preconditioned BGA solder joints exposed to both multiple reflow and thermal cycling. This study applied both numerical and experimental techniques to examine the reliability issue.

The lightweight design of aircraft seats can significantly improve fuel efficiency and reduce greenhouse gas emissions. Metal additive manufacturing (MAM) can produce lightweight topology-optimized designs with improved performance, but limited build volume restricts the printing of large components. The purpose of this paper is to design a lightweight aircraft seat leg structure using topology optimization (TO) and MAM with build volume restrictions, while satisfying structural airworthiness certification requirements.

TO was used to determine a lightweight conceptual design for the seat leg structure. The conceptual design was decomposed to meet the machine build volume, a detailed CAD assembly was designed and print orientation was selected for each component. Static and dynamic verification was performed, the design was updated to meet the structural requirements and a prototype was manufactured.

The final topology-optimized seat leg structure was decomposed into three parts, yielding a 57% reduction in the number of parts compared to a reference design. In addition, the design achieved an 8.5% mass reduction while satisfying structural requirements for airworthiness certification.

To the best of the authors’ knowledge, this study is the first paper to design an aircraft seat leg structure manufactured with MAM using a rigorous TO approach. The resultant design reduces mass and part count compared to a reference design and is verified with respect to real-world aircraft certification requirements.