Search results

This paper aims to investigate the influence of oil–air lubrication flow behavior on point contact sliding wear characteristics.

Oil–air lubrication equations between point contact counterparts were established on the basis of volume of fluid model. The effects of oil supply and injection azimuth on oil-phase volume fraction and its pressure distribution were simulated with commercial software Fluent. Characteristics of point contact sliding wear were then tested with an MFT-3000 friction tester under oil–air lubrication condition. The influence of flow behavior on wear characteristic was investigated combined with numerical and experimental results. The wear mechanism was revealed using SEM, EDS and ferrography.

When air supply speed is constant, the oil-phase volume fraction increases with the increase in oil supply, which helps form continuous oil film and decrease the sliding wear evidently. The injection angle and distance considerably influence the oil–air flow behavior. When injecting at a certain distance and angle, the oil-phase volume fraction reaches its maximum, and the abrasion loss is minimal. Under the test conditions in this study, abrasive particles are mainly debris and a few spiral cuttings. The wear mechanism is abrasive wear.

The influence of the behavior of oil–air lubrication flow on the characteristic of point contact sliding wear is analyzed. This work provides guidance for the application of oil–air lubrication technology in point contact friction pairs.

The purpose of this paper is to design an oil-air lubrication system with low temperature rise, vibration and noise simplifies the spindle configuration. The oil-air lubrication unit is a key component for high-speed grinding machine tools. The development of oil-air lubrication unit suitable for high/ultrahigh rotational speed is a daunting task owing to the lubrication challenges.

This paper emphasizes three main issues: the analysis of oil-air two-phase flow for tradition oil-air lubrication unit with the simulation method; the design of new oil-air lubrication unit for the high/ultrahigh-speed grinding machine tools and the comparative experiment research of tradition and new oil-air lubrication unit. The optimum structure parameters that create the optimum flow pattern and operating conditions resulting in low temperature increase, vibration and noise of oil-air lubricated spindle can be achieved by the simulation method and experiments.

The simulation and experimental results show that new oil-air lubrication unit lubricating a high speed electric spindle has a better performance with a small temperature increase and vibration, which means that our proposed method is an effective design method for oil-air lubrication system.

A design method suitable for high-speed oil-air lubrication unit is proposed. New oil-air lubrication unit is expected to apply for high/ultrahigh rotational speed grinding machine tools.

The purpose of this paper is to investigate that if the lubrication system of a helicopter reducer is compromised, its gears and bearings will be at non-lubricating oil work state, which causes the reducer to be damaged in a very short time.

Various 2 per cent additives were injected and mixed with aeronautical oil to produce 45-min oil/mist lubrication and oil/air lubrication experiments performed upon aeronautical steel tribo-pairs.

The results show that the best anti-wear effect is produced by oil/air lubrication that contains 2 per cent T391. It consumes the least quantity of oil and produces the least wear width, the least rise in temperature and the best surface wear quality.

The technology of oil/air lubrication that contains an extreme-pressure and anti-wear additive is a feasible way to improve the operational ability of a helicopter transmission system that is out of oil.

The purpose of this paper is to design the novel oil–air distributor (N-OAD). Its structure design, oil feeding reliability, service life and viscosity properties of air bubble (AB) oil were analyzed. Meanwhile, the formation mechanism of AB oil was established based on Kelvin–Helmholtz instability.

First, oil–air distributor (OAD) and N-OAD were randomly selected for testing when the air pressure was 0.25 MPa and oil feeding was 100 times per hour. Then, the bubbles were found in the lubricant during the experiment, and the void fraction and viscosity properties of AB oil were tested by image processing method and the MARS 40 rheometer, respectively.

N-OAD has longer service life and higher working reliability than OAD. The key factors of AB oil formation were air pressure and oil feeding. And the void fraction of AB oil has different results on the viscosity at high and low shear rates.

The outcome of this research paper gives an insight to improve the reliability of oil–air lubrication systems and the safety factor of machine tool spindle operation.

The purpose of this paper is to improve the lubrication and remove as much as possible of the heat generated in the bearing assembly, embedded in the jet engine.

To determine the necessary values of the air pressure and oil amount, an experimental approach is used. For that purpose, a custom made test rig is developed.

Less amount of oil makes better lubrication conditions, reflected in the smaller temperature of the bearings. Concerning the air pressure, too high and too low air pressure deteriorates the lubrication parameters. An optimum value should be determined experimentally. The influence of oil amount is remarkably bigger than the influence of air pressure.

This experimental investigation provides an easy and fast way to improve the high-speed bearings lubrication parameters.

This paper aims to investigate the effects of air inlet flow rate on the bearing cavity and operating conditions during the oil-air lubrication.

A model of oil-air lubrication of rolling bearings is established using computational fluid dynamics numerical simulation. Moreover, temperature and vibration experiments are carried out for comparisons and validation.

Results suggest that the velocity and pressure distributions of the oil-air flow inside the chamber are not uniform. Moreover, the uniform decreases with increasing air inlet flow rate. The non-uniform oil distribution inside the bearing significantly influences the bearing temperature rise and lubrication effect. Furthermore, the decrease in pressure uniformity enhances the vibration intensity and increases the amplitude of the vibration acceleration by more than 40 per cent. Increasing the air inlet flow rate improves lubrication and cooling efficiency but produces intense vibrations.

A method of establishing rolling bearings model under oil-air lubrication is presented in the paper. The effect of air inlet flow rate on flow uniform under oil-air lubrication has been researched insightfully. The results provide a useful reference to improve the oil-air lubrication system and enhance the operational stability of the motorized spindle.

Under-race lubrication can increase the amount of lubricating oil entering a bearing and greatly improve lubrication and cooling effects. The oil-air two-phase flow and heat transfer characteristics inside a ball bearing with under-race lubrication play a key role in lubrication and cooling performance. The purpose of this paper is to study these two characteristics, and then provide guidance for lubrication and heat dissipation of bearing with under-race lubrication.

In this paper, a simplified three-dimension heat transfer model of ball bearing with under-race lubrication is established; the coupled level set volume of fluid method is used to track the oil-air two-phase flow, and the Palmgren method is used to calculate the heat generation. The influence of rotation speed and inlet velocity on oil volume fraction, temperature and convection heat transfer is investigated. A temperature test for under-race lubrication is carried out.

Because of the centrifugal force, lubricating oil is located more on the outer ring raceway. As the rotation speed decreases and the inlet velocity increases, the oil volume fraction increases and the temperature decreases. Furthermore, the area with high oil volume fraction has a large convection heat transfer coefficient and low temperature. The error between the simulation temperature and the test temperature is within 10%.

The research on the temperature field and convection heat transfer characteristics of under-race lubrication ball bearings at different rotation speeds and inlet velocities is rarely involved.

For a lightweight and accurate description of bearing temperature, this paper aims to present an efficient semi-empirical model with oil–air two-phase flow and gray-box model.

First, the role of lubricant/coolant in bearing temperature was discussed separately, and the gray-box models on the heat convection inside a bearing cavity were also created. Next, the bearing node setting scheme was optimized. Consequently, a novel semi-empirical two-phase flow thermal grid for high-speed angular contact ball bearings was planned. With this model, the thermal network for the selected motored spindle was built, and the numerical solutions for bearing temperature rise were obtained and contrasted with the experimental values for validation. The polynomial interpolation on test data, meanwhile, was also performed to help us observe the temperature change trend. Finally, the simulations based on the current models of bearings were implemented, whose corresponding results were also compared with our research work.

The validation result indicates that the thermal prediction is more accurate and efficient when the developed semi-empirical oil–air two-phase flow model is employed to assess the thermal change of bearings. Clearly, we provide a more proper model for the thermal assessment of bearing and even spindle heating.

To the best of the authors’ knowledge, this paper introduced the oil–air separation and gray-box model for the first time to describe the heat exchange inside bearing cavities and accordingly presents an efficient semi-empirical oil–air two-phase flow model to evaluate the bearing temperature variation by using thermal network method.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-06-2023-0180/

The study aims to the distribution rule of lubricating oil film of full ceramic ball bearing and improve its performance and life.

The paper established an analysis model based on the fluid–solid conjugate heat transfer theory for full ceramic ball bearings. The distribution of flow, temperature and pressure field of bearings under variable working conditions is analyzed. Meanwhile, the mathematical model of elastohydrodynamic lubrication (EHL) of full ceramic ball bearings is established. The numerical analysis is used to study the influence of variable working conditions on the lubricant film thickness and pressure distribution of bearings. The temperature rise test of full ceramic ball bearing under oil lubrication was carried out to verify the correctness of simulation results.

As the speed increased, the oil volume fraction in full ceramic ball bearing decreased and the surface pressure of rolling element increased. The temperature rise of full ceramic ball bearings increases with increasing speed and load. The lubricant film thickness of full ceramic ball bearing is positively correlated with speed and negatively correlated with load. The pressure of lubricating film is positively correlated with speed and load. The test shows that the higher inner ring speed and radial load, the higher the steady-state temperature rise of full ceramic ball bearing. The test results are in high agreement with simulation results.

Based on the fluid–solid conjugate heat transfer theory and combined with Reynolds equation, lubricating oil film thickness formula, viscosity temperature and viscosity pressure formula. The thermal analysis model and EHL mathematical model of ceramic ball bearings are established. The flow field, temperature field and pressure field distribution of the full ceramic ball bearing are determined. And the thickness and pressure distribution of lubricating oil film in the contact area of full ceramic ball bearing were determined.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2023-0126/

Thermal performances are key factors impacting the operation of angular contact ball bearings. Heat generation and transfer about angular contact ball bearings, however, have not been addressed thoroughly. So far, most researchers only considered the convection effect between bearing housings and air, whereas the cooling/lubrication operation parameters and configuration effect were not taken into account when analyzing the thermal behaviors of bearings. This paper aims to analyze the structural constraints of high-speed spindle, structural features of bearing, heat conduction and convection to study the heat generation and transfer of high-speed angular contact ball bearings.

Based on the generalized Ohm’s law, the thermal grid model of angular contact ball bearing of high-speed spindle was first established. Next Gauss–Seidel method was used to solve the equations group by Matlab, and the nodes temperature was calculated. Finally, the bearing temperature rise was tested, and the comparative analysis was made with the simulation results.

The results indicate that the simulation results of bearing temperature rise for the proposed model are in better agreement with the test values. So, the thermal grid model established is verified.

This paper shows an improved model on forecasting temperature rise of high-speed angular contact ball bearings. In modeling, the cooling/lubrication operation parameters and structural constraints are integrated. As a result, the bearing temperature variation can be forecasted more accurately, which may be beneficial to improve bearing operating accuracy and bearing service life.