Search results

This study aims to determine the appropriate irradiation dose for induction of somaclonal variation in mass of unorganized parenchyma cells derived from sainfoin (Onobrychis viciifolia) tissues.

To investigate the feasibility of UV-B irradiation (312 nm), seeds and callus of sainfoin were exposed to five different intensities (20-100 per cent) for evaluating the effectiveness of phytochemical constituents and cellular behaviour.

Although percentage of seed viability reduced in 20 per cent intensity of UV-B irradiation compared with control seeds, the germination speed significantly enhanced from 3.58 to 5.42. The spectrophotometer analysis confirmed that concentrations of chlorophyll (a and b) decreased after UV-B exposure as compared with control callus. Also, carotenoid content showed significant differences among treated calli. Flavonoid and phenolic contents were observed to gradually increase when the non-irradiated callus subjected to 40 and 60 per cent intensities of UV-B irradiation, respectively. Observation on cellular behaviour such as determination of nuclear and cell areas, mitotic index and chromosomal aberrations were also detected to change in different intensities of UV-B irradiation. Fragmented and aneuploidy aberrations were only observed in exposed cells with more than 40 per cent intensity of UV-B irradiation.

In reality, radiocytological evaluation was proven to be essential in deducing the effectiveness of UV-B irradiation to induce somaclonal variation in callus tissue of sainfoin.

This paper aims to investigate the thermal performance involving larger heating rate, targeted heating, heating with least non-uniformity of the spatial distribution of temperature and larger penetration of heating within samples vs shapes of samples (circle, square and triangular).

Galerkin finite element method (GFEM) with adaptive meshing in a composite domain (free space and sample) is used in an in-house computer code. The finite element meshing is done in a composite domain involving triangle embedded within a semicircular hypothetical domain. The comparison of heating pattern is done for various shapes of samples involving identical cross-sectional area. Test cases reveal that triangular samples can induce larger penetration of heat and multiple heating fronts. A representative material (beef) with high dielectric loss corresponding to larger microwave power or heat absorption in contrast to low lossy samples is considered for the current study. The average power absorption within lossy samples has been computed using the spatial distribution and finite element basis sets. Four regimes have been selected based on various local maxima of the average power for detailed investigation. These regimes are selected based on thin, thick and intermediate limits of the sample size corresponding to the constant area of cross section, Ac involving circle or square or triangle.

The thin sample limit (Regime 1) corresponds to samples with spatially invariant power absorption, whereas power absorption attenuates from exposed to unexposed faces for thick samples (Regime 4). In Regimes 2 and 3, the average power absorption non-monotonically varies with sample size or area of cross section (A_c) and a few maxima of average power occur for fixed values of A_c involving various shapes. The spatial characteristics of power and temperature have been critically analyzed for all cross sections at each regime for lossy samples. Triangular samples are found to exhibit occurrence of multiple heating fronts for large samples (Regimes 3 and 4).

Length scales of samples of various shapes (circle, square and triangle) can be represented via Regimes 1-4. Regime 1 exhibits the identical heating rate for lateral and radial irradiations for any shapes of lossy samples. Regime 2 depicts that a larger heating rate with larger temperature non-uniformity can occur for square and triangular-Type 1 lossy sample during lateral irradiation. Regime 3 depicts that the penetration of heat at the core is larger for triangular samples compared to circle or square samples for lateral or radial irradiation. Regime 4 depicts that the penetration of heat is still larger for triangular samples compared to circular or square samples. Regimes 3 and 4 depict the occurrence of multiple heating fronts in triangular samples. In general, current analysis recommends the triangular samples which is also associated with larger values of temperature variation within samples.

GFEM with generalized mesh generation for all geometries has been implemented. The dielectric samples of any shape are surrounded by the circular shaped air medium. The unified mesh generation within the sample connected with circular air medium has been demonstrated. The algorithm also demonstrates the implementation of various complex boundary conditions in residuals. The numerical results compare the heating patterns for all geometries involving identical areas. The thermal characteristics are shown with a few generalized trends on enhanced heating or targeted heating. The circle or square or triangle (Type 1 or Type 2) can be selected based on specific heating objectives for length scales within various regimes.

This paper aims to propose a mathematical model and numerical modeling to study the behavior of low conductive incompressible multicomponent hydrocarbon mixture in a channel under the influence of electron irradiation. In addition, it also aims to present additional mechanisms to study the radiation transfer and the separation of the mixture’s components.

The three-dimensional non-stationary Navier–Stokes equation is the basis for this model. The Adams–Bashforth scheme is used to solve the convective terms of the equation of motion using a fourth-order accuracy five-point elimination method, and the viscous terms are computed with the Crank–Nicolson method. The Poisson equation is solved with the matrix sweep method and the concentration and electron irradiation equations are solved with the Crank–Nicolson method too.

It shows high computational efficiency and good estimation quality. On the basis of numerical results of mathematical model, the effect of the separation of mixture to fractions with various physical characteristics was obtained. The obtained results contribute to the improvement of technologies for obtaining high-quality oil products through oil separation into light and heavy fractions. Mathematical model is approbated based on test problem, and has good agreement with the experimental data.

The constructed mathematical model makes developing a methodology for conducting experimental studies of this phenomenon possible.

Selective laser sintering (SLS) is a leading process for developing rapid prototype objects by selectively fusing layers of powder according to numerically defined cross‐sectional geometry. The process has the potential to become an indispensable industrial tool. However, continuous process improvement is necessary. Improved understanding of the parameter effects on the process response is expected to lead to process advances. In this work the analytical problem describing the energy delivery, heat transfer and sintering process along with other pertinent phenomena is studied. Physical experiments and implementation of a numerical simulation are conducted using Bisphenol‐A polycarbonate. The effects of selected parameters on the SLS process response are examined. The primary parameters of interest are the laser power, laser beam velocity, hatch spacing, laser beam spot size and scan line length. This work shows that the secondary process parameters, delay period and number of effective exposures have a significant influence on the process response.

The anticorrosion coatings used in marine and atmospheric environment are subjected to many environmental factors. And the aging failure has been puzzling researchers. The purpose of this study is to find the correlation between the initial aging of epoxy coatings and the typical marine atmospheric environmental factors.

The epoxy coatings were subjected to a one-year exposure in three typical marine atmospheres. Meanwhile, principal component analysis, linear regression and Spearman and gray correlation analysis were applied to quantify the environmental characteristics and establish correlations with the coating aging.

The results indicate that the coating will undergo macroscopic fading and chalking upon exposure to the marine atmosphere, while microscopic examination reveals holes, cracks and partial peeling. The adhesion performance and electrochemical properties of the coating deteriorated with prolonged exposure, coating aging mainly occurs with the generation of O-H bonds and the breakage of molecular chains such as C-N and C-O-C. The coating was most deeply aged after exposure to the Xisha, followed by Zhoushan and finally Qingdao. Environmental factors affect the photooxidative aging and hydrolytic degradation processes of coatings and thus coating aging. To further demonstrate the correlation between environmental factors and coating aging, principal component analysis was used. The correlation model between environmental factors and coating aging was subsequently obtained. The correlation model between the rate of coating adhesion loss (E) and the comprehensive evaluation parameter of environmental factors (Z) is expressed as E = 0.142 + 0.028Z. Meanwhile, the Spearman correlation analysis and gray correlation method were used to investigate the impact of each environmental factor on coating aging. Solar irradiation, relative humidity and wetting time have the highest correlation with coating aging, which are all above 0.8 and have the greatest influence on coating aging; wind speed and temperature have the smallest correlation with coating aging, which are about 0.6 and have the least influence on coating aging.

This paper establishes a correlation between typical marine environmental factors and coating aging performance, which is crucial for predicting the service life of other coatings in diverse environments.

This study aims to provide an alternative adoption to overcome the energy crisis and environmental effluence by comparative theoretical and trial testing analysis of an innovative combined condenser unit over traditional individual condenser unit water heating systems.

The presented innovative new unit of the combined condenser heat pipe works efficiently through its improved idea and unique design, providing uniform heating to improve the heat transfer and, finally, the temperature of water increases without enhancing the cost. In this design, all these five evaporator units were connected with a single combined condenser unit in such a manner that after the condensation of heat transfer fluid vapour, it goes equally into the evaporator pipe.

The maximum temperature of hot water obtained from the combined condenser heating system was 60.6, 55.5 and 50.3°C at a water flow rate of 0.001, 0.002 and 0.003 kg/s, respectively. The first and second law thermodynamic efficiency of the combined condenser heating system were 55.4%, 60.5% and 89.0% and 2.6%, 3.7% and 4.1% at 0.001, 0.002 and 0.003 kg/s of water flow rates, respectively. The combined condenser heat pipe solar evacuated tube heating system promoting progressive performance is considered efficient and environment-friendly compared to the traditional condenser unit water heating system.

Innovative combined condenser heat pipe evacuated tube collector assembly was designed and developed for the study. A comparative theoretical and experimental energy-exergy performance analysis was performed of innovated collective condenser and traditional individual condenser heat pipe water heating system at various mass flow rate.

The purpose of this paper is to investigate the effect of high-intensity pulsed ion beam (HIPIB) intensity on the structure and corrosive properties of microarc oxidation (MAO) films on AZ31 magnesium alloy and explore the mechanism for modified anti-corrosion properties of irradiated films.

The energy deposited on the coating surface influences the remelting process of the MAO coatings significantly, which was closely related to the intensity of HIPIB; therefore, HIPIB with various intensities of 100-350 A/cm², was selected to modify the MAO films on AZ31 magnesium alloy. The changes in film structure and phase structure of modified films were characterized by scanning electron microscopy and X-ray diffractometry (XRD) with CuKα, respectively. The corrosive behavior of the MAO films was featured with polarization curves and electrochemical impedance spectrum in 3.5 per cent NaCl solution on a PAR 2273 electrochemical workstation.

The results clearly show that a dense, continual and remelted layer with a few micrometers in thickness was obtained on the irradiated surface at 200 A/cm², which are mainly responsible for the modified and optimal anti-corrosion property of MAO films by suppressing/retarding the process of the corrosive electrolyte infiltration into magnesium substrate surface.

The paper reveals that HIPIB irradiation could modify the corrosion resistance by producing a remelted compact layer on the MAO film surface at a suitable irradiation parameter and explored the modified mechanism of MAO films.

The purpose of this paper is to study the effect of gamma-rays on murexide (Mx) dye and its possible use as radiation dosimeters in two different dosimetry systems. The first system depends on the Mx dye as a liquid dosimeter. The second dosimetry system depends also on the same dye but as in a gel form, which is more sensitive to gamma-rays.

The prepared Mx (solutions/gels) have a considerable two peaks at 324 and 521 nm that upon irradiation, the intensity of these peaks decreases with the increasing radiation dose.

The gamma-ray absorbed dose for these dosimeters was found to be up to 2 kGy for the solution samples and 40 Gy for the gels. Radiation chemical yield, dose response function, radiation sensitivity and before and after-irradiation stability under various conditions were discussed and studied.

It is expected that the radiolysis of the Mx dye can be used as radiation dosimeters in two different dosimetry systems; liquid and gel dosimeters. This can be applied in a wide range of gamma radiation practical industrial applications in water treatment, food irradiation dosimeters, radiotherapy and fresh food irradiation and seed production.

Both of the prepared Mx dyes, either as solutions or gel samples, can be facilely prepared from commercially, cheap, safe, available chemicals and suitable for useful applied Mx solutions and gels radiation dosimeters.

In this article, a unique concept for a device that conducts photochromic measurement in the reflectance mode together with the methodology described has been patented in the Czech Republic in the author's name. This unique device allows measurements of colorimetric and spectral characteristics of photochromic textiles as photochromic sensors and also as a fatigue tester for the control of color change stability. The measurement of colorimetric and spectral parameters in comparison together with the intensity of UV irradiation allows the dependence of color change on intensity of irradiation to determined, and a scale for individual visual observation to be developed, as well as the risks of UV irradiation to be evaluated.

This paper aims to present the numerical models and experimental outcomes pertain to the performance of the parabolic dish concentrator system with a modified cavity-type receiver (hemispherical-shaped).

The numerical models were evolved based on two types of boundary conditions; isothermal receiver surface and non-isothermal receiver surface. For validation of the numerical models with experimental results, three statistical terms were used: mean of absolute deviation, R² and root mean square error.

The thermal efficiency of the receiver values obtained using the numerical model with a non-isothermal receiver surface found agreeing well with experimental results. The numerical model with non-isothermal surface boundary condition exhibited more accurate results as compared to that with isothermal surface boundary condition. The receiver heat loss analysis based on the experimental outcomes is also carried out to estimate the contributions of various modes of heat transfer. The losses by radiation, convection and conduction contribute about 27.47%, 70.89% and 1.83%, in the total receiver loss, respectively.

An empirical correlation based on experimental data is also presented to anticipate the effect of studied parameters on the receiver collection efficiency. The anticipations may help to adopt the technology for practical use.

The developed models would help to design and anticipating the performance of the dish concentrator system with a modified cavity receiver that may be used for applications e.g. power generation, water heating, air-conditioning, solar cooking, solar drying, energy storage, etc.

The originality of this manuscript comprising presenting a differential-mathematical analysis/modeling of hemispherical shaped modified cavity receiver with non-uniform surface temperature boundary condition. It can estimate the variation of temperature of heat transfer fluid (water) along with the receiver height, by taking into account the receiver cavity losses by means of radiation and convection modes. The model also considers the radiative heat exchange among the internal ring-surface elements of the cavity.