Search results

The purpose of this paper is to apply the novel instantaneous power flow balance (IPFB)-based identification strategy to a specific practical situation like nonlinear lap joints having single and double bolts. The paper also investigates the identification performance of the proposed power flow method over conventional acceleration-matching (AM) methods and other methods in the literature for nonlinear identification.

A parametric model of the joint assembly formulated using generic beam element is used for numerically simulating the experimental response under sinusoidal excitations. The proposed method uses the concept of substructure IPFB criteria, whereby the algebraic sum of power flow components within a substructure is equal to zero, for the formulation of an objective function. The joint parameter identification problem was treated as an inverse formulation by minimizing the objective function using the Particle Swarm Optimization (PSO) algorithm, with the unknown parameters as the optimization variables.

The errors associated with identified numerical results through the instantaneous power flow approach have been compared with the conventional AM method using the same model and are found to be more accurate. The outcome of the proposed method is also compared with other nonlinear time-domain structural identification (SI) methods from the literature to show the acceptability of the results.

In this paper, the concept of IPFB-based identification method was extended to a more specific practical application of nonlinear joints which is not reported in the literature. Identification studies were carried out for both single-bolted and double-bolted lap joints with noise-free and noise-contamination cases. In the current study, only the zone of interest (substructure) needs to be modelled, thus reducing computational complexity, and only interface sensors are required in this method. If the force application point is outside the substructure, there is no need to measure the forcing response also.

The purpose of this paper is to provide an effective and simple technique for structural parameter identification, particularly to identify multiple cracks in a structure using simultaneous measurement of acceleration responses and voltage signals from PZT patches which is a multidisciplinary approach. A hybrid element constituted of one-dimensional beam element and a PZT sensor is used with reduced material properties which is very convenient for beams and is a novel application for inverse problems.

Multi-objective formulation is used whereby structural parameters are identified by minimizing the deviation between the predicted and measured values from the PZT patch and acceleration responses, when subjected to excitation. In the proposed method, a patch is attached to either end of the fixed beam. Using particle swarm optimization algorithm, normalized fitness functions are defined for both voltage and acceleration components with weighted aggregation multi-objective optimization technique. The signals are polluted with 5 percent Gaussian noise to simulate experimental noise. The effects of various weighting factors for the combined objective function are studied. The scheme is also experimentally validated by identification of cracks in a fixed-fixed beam.

The numerical and experimental results shows that significant improvement in accuracy of damage detection is achieved by the combined multidisciplinary method, when compared with only voltage or only acceleration-matching method as well as with other methods.

The proposed multidisciplinary crack identification approach, which is based on one-dimensional PZT patch model as well as conventional acceleration method, is not reported in the literature.

Aim of the present monograph is the economic analysis of the role of MNEs regarding globalisation and digital economy and in parallel there is a reference and examination of some legal aspects concerning MNEs, cyberspace and e‐commerce as the means of expression of the digital economy. The whole effort of the author is focused on the examination of various aspects of MNEs and their impact upon globalisation and vice versa and how and if we are moving towards a global digital economy.

Discusses the 27 papers in ISEF 1999 Proceedings on the subject of electromagnetisms. States the groups of papers cover such subjects within the discipline as: induction machines; reluctance motors; PM motors; transformers and reactors; and special problems and applications. Debates all of these in great detail and itemizes each with greater in‐depth discussion of the various technical applications and areas. Concludes that the recommendations made should be adhered to.

At the current stage of electrical technology development, it is relevant to take into account the quality of electrical energy. It can be implemented if an assessed energy quality indicator is available. The amount of electrical energy is determined by active power, which is transmitted over a certain time period. In some cases, reactive power is included in the metering system. The distortion power is justifiably criticized and is not taken into account. The purpose of this paper consists in the substantiation of the indicator of the distortion of the periodic polyharmonic current electrical energy power, by separating from the instantaneous power such harmonics, which formed by same frequencies current and voltage harmonics.

Using the method of calculating linear polyharmonic current circuits, the following quantities are identified in instantaneous power: active, reactive and apparent powers of each harmonic. These components are known from references as canonical.

By the method of instantaneous power harmonic analysis, the components formed by current and voltage harmonics of the same frequency and different frequencies are distinguished.

The RMS value of the instantaneous power due to current and voltage harmonics of different frequencies is justified in the work. This quantity allows you to distinguish the instantaneous power distortion level in comparison with the existing quantity.

The results can be used to assess the level of instantaneous power distortion level in commercial and technical metering systems.

The definition of instantaneous power distortion by extracting the canonical components from it and determining the root mean square value of the remainder is proposed.

This paper aims to propose a novel grid current control strategy for grid-connected voltage source converters (VSCs) under unbalanced grid voltage conditions.

A grid voltage dynamic model is represented in symmetrical positive and negative sequence reference frames. A proportional controller structure with a first-order low-pass filter disturbance observer (DOB) is designed for power control in unbalanced voltage conditions. This controller is capable of meeting the positive sequence power requirements, and it also eliminates negative sequence power components which cause double-frequency oscillations on power. The symmetrical components are calculated by using the second-order generalized integrator-based observer, which accurately estimates the symmetrical components.

Proportional current controllers are sufficient in this study in a wide range of operating conditions, as DOB accurately estimates and feed-forwards nonlinear terms which may be deteriorated by physical and operating conditions. This is the first reported scheme which estimates the VSC disturbances in terms of symmetrical component decomposition and the DOB concept.

The proposed method does not require any grid parameter to be known, as it estimates nonlinear terms with a first-order low-pass filter DOB. The proposed control system is implemented on a dSPACE ds1103 digital controller by using a three-phase, three-wire VSC.

The purpose of this paper is to use numerical simulations to investigate the energy conversion performance and the flow and temperature structures inside horizontal tubes connected to a vertical manifold channel.

The simulations are performed for different flow rates and inlet temperatures using CFD.

In both the “flowing wind mode” and “upwind mode,” the inlet velocity is not infinitely small under the influence of natural convection; however, such small inlet velocities cannot be achieved in practice and are of no practical significance. In the “flowing wind mode,” the appropriate velocity for achieving high efficiency is 0.01-0.02 m/s. In the “upwind mode,” the appropriate velocity for obtaining high efficiency is 0.1-0.2 m/s. A high inlet temperature can lead to high efficiency; therefore, a large temperature difference and a small flow can be used in actual designs.

The energy conversion performance and flow structures inside evacuated tubular collectors were investigated using CFD for different operating conditions, notably in the “following wind mode” and the “upwind mode.”

The purpose of this paper is to propose a new converter topology for integrating PV plants constituted by many panels into the grid. The converter is capable of implementing MPPT algorithms on different subset of modules and can balance the different energy supplied by panels differently irradiated. The output voltage presents a very low ripple also if small filters are used for grid connection.

In the paper, at first the converter configuration is presented. Then a control strategy for obtaining, at the same time the distributed MPPT and the power balancing on the three phases is proposed. Finally, by means of numerical simulations, the good performances of the proposed converter are shown.

The proposed converter, lent from MMC configurations, is deeply studied and a suitable control strategy is well analyzed in the paper. Analytical model for voltage and current balancing are given.

The analysis presented in the paper complete some studies started in the last years and partially presented in previous scientific papers. It reaches a final point and gives all the specific for the realization of the converter and of its control.

The paper gives all the instrument to design and realize a PV power plant integrated into building façade.

The converter and the control for voltage and current balancing presented in this paper represent a significant original contribution of this work.

Turbomachinery, including pumps, are mainly designed to extract/produce energy from/to the flow. A major challenge in the numerical simulation of turbomachinery is the inlet flow rate, which is routinely treated as a known boundary condition for simulation purposes but is properly a dependent output of the solution. As a consequence, the results from numerical simulations may be erroneous due to the incorrect specification of the discharge flow rate. Moreover, the transient behavior of the pumps in their initial states of startup and final states of shutoff phases has not been studied numerically. This paper aims to develop a coupled procedure for calculating the transient inlet flow rate as a part of the solution via application of the control volume method for linear momentum. Large eddy simulation of a four-blade axial hydraulic pump is carried out to calculate the forces at every time step. The sharp interface immersed boundary method is used to resolve the flow around the complex geometry of the propeller, stator and the pipe casing. The effect of the spurious pressure fluctuations, inherent in the sharp interface immersed boundary method, is damped by local time-averaging of the forces. The developed code is validated by comparing the steady-state volumetric flow rate with the experimental data provided by the pump manufacturer. The instantaneous and time-averaged flow fields are also studied to reveal the flow pattern and turbulence characteristics in the pump flow field.

The authors use control volume analysis for linear momentum to simulate the discharge rate as part of the solution in a large eddy simulation of an axial hydraulic pump. The linear momentum balance equation is used to update the inlet flow rate. The sharp interface immersed boundary method with dynamic Smagorinsky sub-grid stress model and a proper wall model is used.

The steady-state volumetric flow rate has been computed and validated by comparing to the flow rate specified by the manufacturer at the simulation conditions, which shows a promising result. The instantaneous and time averaged flow fields are also studied to reveal the flow pattern and turbulence characteristics in the pump flow field.

An approach is proposed for computing the volumetric flow rate as a coupled part of the flow solution, enabling the simulation of turbomachinery at all phases, including the startup/shutdown phase. To the best of the authors’ knowledge, this is the first large eddy simulation of a hydraulic pump to calculate the transient inlet flow rate as a part of the solution rather than specifying it as a fixed boundary condition. The method serves as a numerical framework for simulating problems incorporating complex shapes with moving/stationary parts at all regimes including the transient start-up and shut-down phases.

This paper aims to propose an improved multifunctional control strategy for achieving real, reactive power flow control and the mitigation of power quality issues in grid integrated photovoltaic (GIPV) systems.

The paper proposes a dual stage, three phase, multifunctional GIPV system with modified instantaneous reactive power (IRP) theory-based and modified synchronous reference frame (SRF) theory-based control algorithms for reference template generation with continuous load power requirement tracking. The control structure is designed so as to impart virtual distribution static compensator functionality to the photovoltaic inverter. The dual mode operation in active filter and renewable power injection modes provides enhanced capability to the GIPV system. A comprehensive evaluation of the dynamic behaviour of the GIPV system is carried out for various conditions of irradiance and load under MATLAB/Simulink platform. The performance comparison is done considering an uncompensated system and the GIPV system with both proposed control algorithms.

The extensive simulation results demonstrate that the proposed modified SRF theory-based multifunctional control strategy shows superior performance in real and reactive power flow control; reduction in real and reactive burden of the utility grid; and regulation of dc bus voltage under varying scenarios of irradiance and load. Furthermore, there is improvement of grid power factor and reduction in total harmonic distortion of grid currents in compliance with the IEEE 519 standard even with highly non-linear loads at the point of common coupling.

The proposed modified SRF theory-based multifunctional controller offers a viable solution for power quality enhancement as well as the realization of effective real and reactive power flow control in GIPV systems. Thus, the penetration level of distributed generation can be increased in this era of global energy crisis.