Search results

The purpose of this paper is to propose a new converter topology for integrating PV plants constituted by many panels into the grid. The converter is capable of implementing MPPT algorithms on different subset of modules and can balance the different energy supplied by panels differently irradiated. The output voltage presents a very low ripple also if small filters are used for grid connection.

In the paper, at first the converter configuration is presented. Then a control strategy for obtaining, at the same time the distributed MPPT and the power balancing on the three phases is proposed. Finally, by means of numerical simulations, the good performances of the proposed converter are shown.

The proposed converter, lent from MMC configurations, is deeply studied and a suitable control strategy is well analyzed in the paper. Analytical model for voltage and current balancing are given.

The analysis presented in the paper complete some studies started in the last years and partially presented in previous scientific papers. It reaches a final point and gives all the specific for the realization of the converter and of its control.

The paper gives all the instrument to design and realize a PV power plant integrated into building façade.

The converter and the control for voltage and current balancing presented in this paper represent a significant original contribution of this work.

In the dispersed generation system, power electronic converters allow for coupling between energy sources and the power grid. The requirements of Transmission System Operators are difficult to meet when the share of distributed energy sources of the total energy balance increases. These requirements allow to increase penetration of distributed generation sources without compromising power system stability and reliability. Therefore, in addition to control of active or reactive power, as well as voltage and frequency stabilization, the modern power electronic converters should support power grid in dynamic states or in the presence of nonlinear distortions. The paper aims to discuss these issues.

The research methodology used in this paper is based on three steps: Mathematical modelling and simulation studies, Experiments on laboratory test stand, Analyzing obtained results, evaluating them and formulating the conclusions.

The authors identified two algorithms, αβ-Filter and Voltage Controlled Oscillator, which are able to successfully cope with notch distortions. Other algorithms, used previously for voltage dips, operate improperly when the voltage grid has notching disturbances. This work evaluates six different synchronization algorithms with respect to the abilities to deal with notching.

The paper presents results of the synchronization algorithms in the presence of nonlinear notching interference. These studies were performed using the original hardware-software power grid emulator, real-time d’Space platform and power electronic converter. This methodology allowed us to exactly and accurately evaluate synchronization performance methods in the presence of complex nonlinear phenomena in power grid and power electronic converter. The results demonstrated that the best algorithms were αβ – Filtering and Voltage Controlled Oscilator.

In this paper, different synchronization algorithms have been tested. These included the classical Phase Locked Loop with Synchronous Reference Frame as well as modified algorithms developed by the authors, which displayed high robustness with respect to the notching interference. During the tests, the previously developed original test rig was used, allowing software-hardware emulation of grid phenomena.

Votage source converter (VSC) based or current source converter (CSC) based shunt active power filter (SAPF)? It is the main question in harmonic elimination project using SAPF.This paper presents some criteria based on which the designer can decide which type of filter is more suitable for implementation of the project according to the nature and characteristics of the project.

Owing to the importance of cost and power losses criteria, relevant equations will be formulated and comparative analysis will be carried out between conventional structures based on CSC or VSC. For validation of analyses, simulation results have been studied in the MATLAB–SIMULINK environment.

Simulation results have examined two important criteria of power losses and costs. Although the results show the superiority of VSSAPF to CSSAPF in both criteria, this comparison is performed in a general and conventional condition. Using third-order filters of inductive-capacitive-inductive (LCL) type in VSSAPF, using insulated-gate bipolar transistor (IGBT) with reverse-voltage blocking ability in CSSAPF, which eliminates the need to use series diodes, and the use of superconducting technology in the DC-side endpoint in CSSAPF, not only reduce the difference of cost and losses in two schemes but also may lead to the lower costs and losses in CSSAPF than VSSAPF.

This paper is the result of many years working on active power filter and can be useful for engineers who are engaged in industrial projects.

The purpose of this paper is to consider both sides of a back‐to‐back AC‐DC‐AC interface.

The paper presents a mathematical analysis, simulation, laboratory test in scaled model.

The two main findings comprised concept of control methods for grid AC‐DC‐AC converter applied in renewable energy sources with variable speed operation under distorted grid. Active filtering functionality in case of non‐linear current of a parallel load. Second, a control algorithm dedicated for two‐level AC‐DC converter applied in industrial networks with high‐order harmonics compensation working under hard conditions – balanced and unbalanced voltage dips.

The paper shows preliminary results for AC‐DC‐AC converter and active filter (AF) during voltage dips and for harmonics compensation. Control methods and/or topology should be improved and tested in scale and after at high‐power system.

Power quality supplied/received to/from the grid can be increased. In case of low‐cost system only AF can be applied to existing non‐linear receivers. Moreover, in case of full AC‐DC‐AC converter energy saving and production is possible.

Presented control methods give satisfactory results. Paper presents laboratory results for grid and machine side two different power circuits during steady states and transients. Moreover, active filtering operation during voltage dips is presented.

Power converters are an integral part of the energy conversion process in solar photovoltaic (PV) systems which is used to match the solar PV generation with the load requirements. The increased penetration of renewable invokes intermittency in the generated power affecting the reliability and continuous energy supply of such converters. DC-DC converters deployed in solar PV systems impose stringent restrictions on supplied power, continuous operation and fault prediction scenarios by continuously observing state variables to ensure continuous operation of the converter.

A converter deployed for a mission-critical application has to ensure continuous regulated output for which the converter has to ensure fault-free operation. The fault diagnostic algorithm relies on the measurement of a state variable to assess the type of fault. In the same line, a predictive controller depends on the measurement of a state variable to predict the control variable of a converter system to regulate the converter output around a fixed or a variable reference. Consequently, both the fault diagnosis and the predictive control algorithms depend on the measurement of a state variable. Once measured, the available data can be used for both algorithms interchangeably.

The objective of this work is to integrate the fault diagnostic and the predictive control algorithms while sharing the measurement requirements of both these control algorithms. The integrated algorithms thus proposed could be applied to any converter with a single inductor in its energy buffer stage.

laboratory prototype is created to verify the feasibility of the integrated predictive control and fault diagnosis algorithm. As the proposed method combine the fault detection algorithm along with predictive control, a load step variation and manual fault creation methods are used to verify the feasibility of the converter as with the simulation analysis. The value for the capacitors and inductors were chosen based on the charge-second and volt-second balance equations obtained from the steady-state analysis of boost converter.

This paper aims to present the analysis, design and implementation of functional link-based recurrent fuzzy neural network (FLRFNN) for the control of variable-speed switched reluctance generator (SRG).

The node connecting weights of the FLRFNN are trained online by back-propagation (BP) algorithms. The proposed estimator requires less processing time than traditional methods and can be fully implemented using a low-cost digital signal processor (DSP) with MATLAB toolboxes. The DSP-based hybrid sensor presented in this paper can be applied to a wind energy-conversion system where the SRG is used as a variable-speed generator. The current transducer is used to monitor the energized current and proximity sensors for rotor salient.

The authors have found that optimal based on FLRFNN with Grey controller can resolve the regulation of the system with uncertainty model and unknown disturbances. This technique can maintain the system stability and reach the desired performance even with parameter uncertainties.

This design will improve the performance of SRG to operate more smoothly. This application is currently being studied because the SRG has well-known advantages such as robustness, low manufacturing cost and good size-to-power ratio. Performance of the proposed controller can offer better stability characteristics. Finally, the SRG has a very good efficiency in the whole operating range.

The purpose of this study is to present a new methodology of selective harmonics elimination (SHE) technique suitable for single-phase photovoltaic (PV) tied pulse width modulated (PWM) inverter.

In the proposed SHE, switching angles for inverter control are determined offline through numerical techniques and stored in a microcontroller memory as a function of modulation index (md). The methodology uses the solution that leads to a lower change of switching angles from the previous modulation index (md) for storing in the processor memory for multiple solutions. This leads to a smaller number of sections when a piecewise mixed model is considered for storing the entire switching angle curve for the online inverter control. The proposed idea is simulated and experimentally validated on a laboratory prototype of PV (500 W) grid-tied PWM inverter. The control environment is then realized in NI c-RIO 9082.

This proposed technique is suitable for limiting voltage total harmonics distortion (THD) in single-phase PV tied grid connected voltage source inverter (VSI). Moreover, it is found that filter (L-C) size requirement is less.

The proposed SHE with piecewise mixed model technique effectively reduces voltage THD with less filter size (L-C) in a single-phase PV-tied system.

Power‐electronic systems have been playing a significant role in the integration of large‐scale wind turbines into power systems due to the fact that during the past three decades power‐electronic technology has experienced a dramatic evolution. This second part of the paper aims to focus on a comprehensive survey of power converters and their associated control systems for high‐power wind energy generation applications.

Advanced control strategies, i.e. field‐oriented vector control and direct power control, are initially reviewed for wind‐turbine driven doubly fed induction generator (DFIG) systems. Various topologies of power converters, comprising back‐to‐back (BTB) connected two‐ and multi‐level voltage source converters (VSCs), BTB current source converters (CSCs) and matrix converters, are identified for high‐power wind‐turbine driven PMSG systems, with their respective features and challenges outlined. Finally, several control issues, viz., basic control targets, active damping control and sensorless control schemes, are elaborated for the machine‐ and grid‐side converters of PMSG wind generation systems.

For high‐power PMSG‐based wind turbines ranging from 3 MW to 5 MW, parallel‐connected 2‐level LV BTB VSCs are the most cost‐effective converter topology with mature commercial products, particularly for dual 3‐phase stator‐winding PMSG generation systems. For higher‐capacity wind‐turbine driven PMSGs rated from 5 MW to 10 MW, medium voltage multi‐level converters, such as 5‐level regenerative CHB, 3‐ and 4‐level FC BTB VSC, and 3‐level BTB VSC, are preferred. Among them, 3‐level BTB NPC topology is the favorite with well‐proven technology and industrial applications, which can also be extensively applicable with open‐end winding and dual stator‐winding PMSGs so as to create even higher voltage/power wind generation systems. Sensorless control algorithms based on fundamental voltages/currents are suggested to be employed in the basic VC/DPC schemes for enhancing the robustness in the entire PMSG‐based wind power generation system, due to that the problems related with electromagnetic interferences in the position signals and the failures in the mechanical encoders can be avoided.

This second part of the paper for the first time systematically reviews the latest state of arts with regard to power converters and their associated advanced control strategies for high‐power wind energy generation applications. It summarizes a variety of converter topologies with pros and cons highlighted for different power ratings of wind turbines.

The power electronic converter is used for the satisfaction of reactive power demand of induction generator, when grid-tied. This paper aims to present an application of STATCOM to reduce inrush transient caused by the connection of a squirrel-cage induction generator (SCIG) to the grid.

The power generation system consists of an uncontrolled prime mover, a SCIG and a power electronic converter connected to the grid. The three-phase Neutral Point Clamped (NPC) converter works as a STATCOM to satisfy a reactive power demand of the generator. A control scheme of STATCOM uses the x-y reference frame rotating synchronously with grid voltage vector and the p-q instantaneous power theory to calculate q component of grid power.

It is shown that the parallel converter, which works as a reactive power compensator allows decreasing transients during a grid connection of the induction generator.

Transients during a grid connection of the induction generator are only partially decreased.

It is needed to compensate for the reactive power of a SCIG. The NPC converter works as a STATCOM. The converter partially reduces grid transients during generator connection. The laboratory tests are demonstrated by connection 7.5 kW induction generator to 8 kVA transformer.

The paper presents the mitigation of grid transients during connection of induction generator with the power electronic converter working as reactive power compensator.