Search results

This paper aims to investigate the thermal stability and hydrophobicity of difference alkyl chain of silanes with silicon (Si) micro- and nanoparticles.

Sol-gel methods have been used to design superhydrophobic glass substrates through surface modification by using low-surface-energy Isooctyl trimethoxysilane (ITMS) and Ethyl trimethoxysilane (ETMS) solution. Hierarchical double-rough scale solid surface was built by Si micro- and nanoparticles to enhance the surface roughness. The prepared sol was applied onto glass substrate using dip-coating method and was dried at control temperature of 400°C inside the tube furnace.

The glass substrate achieved the water contact angle as high as 154 ± 2° and 150.4 ± 2° for Si/ITMS and Si/ETMS films, respectively. The Si/ITMS and Si/ETMS also were equipped with low sliding angle as low as 3° and 5°, respectively. The Si micro- and nanoparticles in the coating system have created nanopillars between them, which will suspend the water droplets. Both superhydrophobic coatings have showed good stability against high temperature up to 200°C as there are no changes in WCA shown by both coatings. Si/ITMS film sustains its superhydrophobicity after impacting with further temperature up to 400°C and turns hydrophobic state at 450°C.

Findings will be useful to develop superhydrophobic coatings with high thermal stability.

Sol method provides a suitable medium for the combination of organic-inorganic network to achieve high hydrophobicity with optimum surface roughness.

Application of different alkyl chain groups of silane resin blending with micro- and nanoparticles of Si pigments develops superhydrophobic coatings with high thermal stability.

The purpose of this paper is to develop a potential nanoparticles lubricant additive for solving the problem of the insolubility and stable dispersity; the complex nanoparticles with core-shell structures are less studied in the field. Therefore, this paper determines novel complex nanoparticles and their tribological properties.

According to the conventional preparation method, the complex nanoparticle styrene/calcium borate (PS/O-CaB) was synthesized. The microstructures of the as-obtained samples were characterized by X-ray diffraction infrared spectroscopy and thermogravimetric analysis. Tribological properties of PS/O-CaB used as lubricating oil additive were evaluated on four-ball tribometer. The worn surface of the steel ball was investigated by a three-dimensional non-contact surface profilometer and X-ray photoelectron spectroscopy (XPS).

The results of the structure characteristic indicate two different crystalline forms, namely, Ca₂B₆O₁₁ and Ca₂B₂O₅, and the average size of calcium borate nanoparticles in PS/O-CaB is about 20-40 nm. Moreover, the good tribological properties are due to a wear resistance film containing both depositions and the tribochemical reaction products which comprise B2O3, FeB and Fe2O3.

Novel complex nanoparticles with core-shell structure (PS/O-CaB) were successfully prepared. Moreover, the PS/O-CaB shows excellent tribological capacity such as load-carrying, friction-reducing and antiwear property.

The purpose of this study was to investigate the effects of CaCO₃ nanoparticles on the mechanical properties, and mixed-mode fracture behavior of acrylonitrile butadiene styrene 3D printed samples with different internal architectures.

The nanocomposite filaments have been fabricated by a melt-blending technique. The standard tensile, compact tension and special fracture test samples, named Arcan specimens, have been printed at constant extrusion parameters and at four different internal patterns. A special fixture was used to carry out the mixed-mode fracture tests of Arcan samples. Finite element analyses using the J-integral method were performed to calculate the fracture toughness of such samples. The fractographic observations were used to evaluate the mechanism of fracture at different concentrations of nanoparticles.

The addition of CaCO₃ nanoparticles has resulted in a significant increase in the fracture loading of the samples, although this increase was not consistent for all the filling patterns, being more significant for samples with linear and triangular structures. According to the fractographic observations, the creation of uniformly distributed microvoids due to the blunting effect of nanoparticles and 3D stress state at the crack tip in the samples with linear and triangular structures justify the enhancement in the fracture loading by the addition of CaCO₃ nanoparticles in the matrix.

There is a significant gap in the knowledge of the effects of different nanoparticles in the polymer samples produced by the fused filament fabrication process. One of such nanoparticles is an inorganic CaCO₃ nanoparticle that has been frequently used as nanofillers to improve the thermomechanical properties of thermoplastic polymers. Here, experimental and numerical studies have been conducted to investigate the effects of such nanoadditives on the mechanical and fracture behavior of 3D printed samples.

The purpose of this paper is to investigate the possibility of using the iron nanoparticles and iron nanoparticles coated with copper layer as additives to base oils.

Fe and Fe+Cu nanoparticles were synthesized by a reduction modification method and added to mineral oil. The size and structure of prepared nanoparticles were characterized by SEM, TEM, XRF, AAS and XRD analysis. Tribological properties of modified lubricants were evaluated on a four‐ball machine in a model of sliding friction pairs.

Spectral and microscopy analysis evidently displayed the formation of Fe and Fe+Cu nanoparticles in suspensions of colloidal solutions and oil. The size of formed nanoparticles was in 15‐50 nm range. Tribological experiments show good lubricating properties of oils modified with Fe and Fe+Cu nanoparticles: higher wear resistance (55 per cent and 46 per cent accordingly) and lower friction coefficient (30 per cent and 26 per cent accordingly). The tests show that nanoparticles provide decreasing tendency of friction torque during the operation of friction pair.

The paper demonstrates that iron nanoparticles and iron nanoparticles coated with copper layer, not only reduce the wear and friction decrease of friction pairs, but possibly also can create layer in oil which separates two friction surfaces and have some self‐organisation properties.

This study aims to explore the synergistic effect of oxide nanoparticles (ZnO, Fe₂O₃, SiO₂) and cerium nitrate inhibitor on anti-corrosion performance of epoxy coating. First, cerium nitrate inhibitors are absorbed on the surface of various oxide nanoparticles. Thereafter, epoxy nanocomposite coatings have been fabricated on carbon steel substrate using these oxide@Ce nanoparticles as both nano-fillers and nano-inhibitors.

To evaluate the impact of oxides@Ce nanoparticles on mechanical properties of epoxy coating, the abrasion resistance and impact resistance of epoxy coatings have been examined. To study the impact of oxides@Ce nanoparticles on anti-corrosion performance of epoxy coating for steel, the electrochemical impedance spectroscopy has been carried out in 3% NaCl solution.

ZnO@Ce3+ and SiO2@Ce3+ nanoparticles provide more enhancement in the epoxy pore network than modification of the epoxy/steel interface. Whereas, Fe2O3@Ce3+ nanoparticles have more to do with modification of the epoxy/steel interface than to change the epoxy pore network.

Incorporation of both oxide nanoparticles and inorganic inhibitor into the epoxy resin is a promising approach for enhancing the anti-corrosion performance of carbon steel.

The paper aims to investigate the effect of Degussa P-25 Titanium Dioxide (TiO₂) nanoparticles on hydrophobicity and self-cleaning ability as a single organic coating on glass substrate.

Two methods have been used to enhance the hydrophobicity on glass substrates, namely, surface modification by using low surface energy isooctyltrimethoxysilane (ITMS) solution and construction of rough surface morphology using Degussa P-25 TiO₂ nanoparticles with simple bottom-up approach. The prepared sol was applied onto glass substrate using dip-coating technique and stoved in the vacuum furnace 350°C.

The ITMS coating with nano TiO₂ pigment has modified the glass substrate surface by achieving the water contact angle as high as 169° ± 2° and low sliding angle of 0° with simple and low-cost operation. The solid and air phase interface has created excellent anti-dirt and self-cleaning properties against dilute ketchup solution, mud and silicon powder.

Findings will be useful in the development of self-cleaning and anti-dirt coating for photovoltaic panels.

Sol method provides the suitable medium for the combination of organic–inorganic network to achieve high superhydrophobicity and optimum self-cleaning ability.

Application of blended organic–inorganic sol as self-cleaning and anti-dirt coating film.

Gold clusters supported on oxide surface are most promising as active sites as biochemical sensors, in optical industry and catalysis, but there is no information about application of these nanoparticles in analytical chemistry for the chromatographical separation of organic compounds. Thus, the aim of this paper is the development of new separation systems based on gold nanoparticles.

The novel nanohybride system based on gold nanoparticles, cysteine and inorganic matrixes was synthesis. The results were obtained by the combined approach consisting quantum‐chemical calculations, direct organic synthesis and using chromatography investigation of obtained sorbent for separation of aminopyridines.

The structure optimization of cysteine‐gold cluster complexes reveals that adsorbed acid greatly changes the structure of gold nanoparticle and, consequently, changes its properties. The most bond energy is calculated for L‐form 82 kcal/mol. Material based on alumina, modified gold nanoparticle with L‐cysteine was synthesized and capacity coefficients for model compounds majoring by chromatography technique were obtained.

The developed sorbent that consists of alumina, gold nanoparticle and organic ligand (L‐cysteine) can used in analytical chemistry for the chromatographical separation of aminopyridine. The material has same advantages: simple sorbent synthesis, stability and repeatability in separation experimental. The presented novel nanohybride system is protected by Russian patent.

The paper presents a successful application of nanogold for analytical separation of organic compounds, new knowledge about properties of gold in nanosized region and information about bonding sulfur with nanocluster's surfaces, obtained by model physical‐chemistry methods.

This paper aimed to prepare a kind of ZnS nanoparticles/poly(phenylene vinylene) (PPV) nanofibre and investigate its properties. Because the ZnS nanoparticles are important optoelectronic materials, their incorporation into one-dimensional (1D) nanoscale polymer matrices should be a meaningful subject for electrospinning.

ZnS/PPV composite nanofibres with an average diameter of 600 nm were successfully prepared by a combination of the in situ method and electrospinning technique. The nanofibres were electrospun from Zn(CH3COO)2·2H2O and PPV precursor composite solution, and the ZnS/PPV fibres were obtained by exposure of the electrospun fibres to H₂S gas to prepare ZnS nanoparticles in situ. Such fibres were characterised using X-ray Diffraction (XRD), Fourier transform infrared, transmission electron microscope (TEM), scanning electron microscope and photoluminescence (PL). The photoelectric properties of the fibres obtained were also investigated.

XRD patterns proved that ZnS nanocrystals generated in the composite nanofibres. The TEM image showed that the nanocrystals were homogeneously dispersed in the nanofibres. The PL spectrum of ZnS/PPV composite nanofibres exhibited a blue shift relative to the PPV nanofibres. I-V curve of the single nanofibre device under 5.76 mW/cm2 light illumination showed that the composite nanofibres have good photoelectric properties.

The comparisons of advantages between ZnS/PPV nanofibres with similar nanofibres will be further expanded in a later research.

Results demonstrate the promise of these novel nanostructures as ultraminiature photodetectors with the potential for integration into future hybrid nanophotonic devices and systems.

The integration of inorganic semiconductor nanoparticles into organic conjugated polymers leads to composite materials with unique physical properties and important application potential. In this work, ZnS nanoparticles were introduced into PPV by an in situ method, so as to obtain a kind of novel 1D nanomaterials with good photoelectric properties.

This study aims to motivate the application of some low-cost minerals in synthesizing nanoparticles as effective additives on the performance of liquid crystal (LC) hydroxypropyl cellulose (HPC) nanocomposite film, in comparison with carbon nanoallotrope.

Metallic nanoparticles of vanadium oxide, montmorillonite (MMT) and bentonite were synthesized and characterized by different techniques (Transmission electron microscopy [TEM], X-ray diffraction [XRD] and Fourier transform infrared [FTIR]). While the XRD, FTIR, non-isothermal analysis thermogravimetric analysis, mechanical analysis, scanning electron microscope and polarizing microscope were techniques used to evaluate the key role of metallic nanoparticles on the performance of HPC-nanocomposite film.

The formation of nanoparticles was evidenced from TEM. The XRD and FTIR measurements of nanocomposite films revealed that incorporating the mineral nanoparticles led to enhance the HPCs crystallinity from 14% to 45%, without chemical change of HPC structure. It is interesting to note that these minerals provide higher improvement in crystallinity than carbon nanomaterials (28%). Moreover, the MMT provided film with superior thermal stability and mechanical properties than pure HPC and HPC containing carbon nanoparticles, where it increased the E_a from 583.6 kJ/mol to 669.3 kJ/mol, tensile strength from 2.25 MPa to 2.8 MPa, Young’s modulus from 119 MPa to 124 MPa. As well as it had a synergistic effect on the LC formation and the birefringence texture of the nanocomposites (chiral nematic).

Hydroxylpropyl cellulose-nanocomposite films were prepared by dissolving the HPC powder in water to prepare 50% concentration, (free or with incorporating 5% synthesized nanoparticles). To obtain films with uniform thickness, the prepared solutions were evenly spread on a glass plate via an applicator, by adjusting the thickness to 0.2 mm, then air dried.

These minerals provide higher improvement in crystallinity than carbon nanomaterials (28%), moreover, the MMT and bentonite provided films with superior thermal stability than pure HPC and HPC containing carbon nanoparticles. The mineral nanoparticles (especially MMT nanoclays) had a synergistic effect on LC formation and the birefringence texture of the nanocomposites (chiral nematic).

This study presents the route to enhance the utilization of claystone available in El-Fayoum Province as the precursor for nanoparticles and production high performance LC nanocomposites.

This study presents the route for the valorization of low-cost mineral-based nanoparticles in enhancing the properties of HPC-film (crystallinity, thermal stability, mechanical strength), in comparison with carbon-based nanoparticles. Moreover, these nanoparticles provided more ordered mesophases and, consequently, good synergetic effect on LCs formation and the birefringence texture of the HPC-films.

This study aims to investigate the effects of nano or inorganic fillers on unsaturated polyester’s (UPE) thermal, mechanical, and physical properties. UPE reinforced with nanoparticles shows better properties than the pure polymer itself. Nano or inorganic fillers are used in the polymeric matrix to improve thermal, mechanical and physical properties.

To improve thermal, mechanical and physical properties, UPE resin was modified with silica (S), boron nitride (BN) and S/BN hybrid nanoparticles at different ratios. Viscosity and solids content measurement, Fourier transform infrared spectroscopy, contact angle measurement, scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and thermal conductivity coefficient tests were performed on the samples.

In the SEM analysis, the UPE sample showed a smooth appearance, while all samples containing additives showed phase separation and overall heterogeneous distribution. TGA results demonstrated that the thermal stability of the resin increased in the presence of S and BN additives. According to the results, it was observed that the presence of S and BN additives in the UPE resin and the use of certain ratios improved the resin properties.

As a result of the literature search, to the best of the authors’ knowledge, no study was found in which BN nanoparticles were included in the UPE resin together with S.