Search results

The interaction between mixed convection and thermal radiation in ventilated cavities with gray surfaces has been studied numerically using the Navier‐Stokes equations with the Boussinesq approximation. The effect of thermal radiation on streamlines and isotherms is shown for different values of the governing parameters namely, the Rayleigh number (10³ ≤ Ra ≤ 10⁶), the Reynolds number (50 ≤ Re ≤ 5000) and the surfaces emissivity (0 ≤ ε≤ 1). The geometrical parameters are the aspect ratio of the cavity A = L’/H’ = 2 and the relative height of the openings B = h’/H’ = 1/4. Results of the study show that thermal radiation alters significantly the temperature distribution, the flow fields and the heat transfer across the active walls of the cavities.

The purpose of this paper is to study the combined effects of moisture and radiation on thermal protective performance of protective clothing exposed to low level radiation.

Using a sweating manikin, the effect of radiation and moisture on heat and moisture transfer was initially analyzed under the dry manikin with sweating rate of 100 g/(m2h) exposed to 2.5 kW/m2, and then studied at 200 and 300 g/(m2h) exposed to 2 and 3 kW/m2, respectively. Finally, the combined effects of thermal radiation and moisture were predicted by fitting the relationships among heat loss and wet skin surface temperature, with the sweating rate and radiation intensity.

The results show that the heat loss and the wet skin surface temperature are affected by the combined effects of moisture and radiation, with two distinctly different trends. Heat loss from the manikin is increasing with the sweating rate, and decreasing with thermal radiation intensity. However, the wet skin surface temperature has an opposite situation.

Two filling equations are given to present the relationships among heat loss and wet skin surface temperature, with the sweating rate and radiation intensity. With these two equations, the heat loss and the wet skin surface temperature when exposed to radiation can be predicted by only measuring the mean radiant and ambient temperatures and controlling the sweating rate.

This paper's aim is to investigate the effect of surface radiation on the developing laminar forced convection flow of a transparent gas between two vertical parallel plates. The walls are heated asymmetrically, this enhances the effect of radiation even with the two walls having low values of emissivity.

Numerical techniques were used to study the effect of the controlling parameters on wall temperatures, fluid temperature profiles, and Nusslet number.

The values of the radiation number at which surface radiation can engender symmetric heating (and hence maximum average Nusslet number on the heated wall and maximum reduction in the maximum heated wall temperature are achieved) are obtained. Threshold values of the radiation number at which radiation effects can be neglected are obtained.

Boundary‐layer flow model is used.

The implications include design of high‐temperature gas‐cooled heat exchangers, advanced energy conversion devices, advanced types of power plants, and many others.

Though a number of analyses of internal flows including radiation effect have been made, most have been directed at the simplest case of the prescribed uniform (isothermal) temperature boundary condition. The available literature that deals with the problem with prescribed heat flux at the walls is limited to fully developed flow or specifying the convection coefficient a priori. The lack of both theoretical and experimental data concerning combined forced convection and surface radiation developing flows between two parallel and its practical importance motivated the present work.

Hybrid nanofluids are of significant engrossment for their considerable heat transport rate. The steady flow of an incompressible viscous electrically conducted hybrid nanofluid is considered over a rotating disk under a magnetic field. Titanium oxide (TiO₂) and ferrous (CoFe₂O₄) nanoparticles are used with their physical properties and water is considered as host liquid. The purpose of this paper is to analyze how hydrothermal integrity varies for hybrid nanosuspension over a spinning disk in the presence of magnetic orientation.

Governing equations with boundary conditions are transformed by similarity transformations and then solved numerically with RK-4 method. A comparison of linear and nonlinear thermal radiation for the above-mentioned parameters is taken and the efficiency of nonlinear radiation is established, the same over nanofluid and hybrid nanofluid is also discussed. Heat lines are observed and discussed for various parameters like magnetic field, concentration, suction and injection parameter, radiation effect and Prandtl number.

Suction and increasing nanoparticle concentration foster the radial and cross-radial velocities, whereas magnetization and injection confirm the reverse trend. The rate of increment of radial friction is quite higher for the usual nanosuspension. The calculated data demonstrate that the rate for hybrid nanofluid is 8.97 percent, whereas for nanofluid it is 15.06 percent. Double-particle suspension amplifies the thermal efficiency than that of a single particle. Magnetic and radiation parameters aid the heat transfer, but nanoparticle concentration and suction explore the opposite syndrome. The magnetic parameter increases the heat transport at 36.58 and 42.71 percent for nonlinear radiation and hybrid nanosuspension, respectively.

Nonlinear radiation gives a higher heat transport rate and for the radiation parameter it is almost double. This result is very significant for comparison between linear and nonlinear radiation. Heat lines may be observed by taking different nanoparticle materials to get some diverse result. Hydrothermal study of such hybrid liquid is noteworthy because outcomes of this study will aid nanoscience and nanotechnology in an efficient way.

The solution of radiative heat transfer problems in participating media is often obtained using the standard discrete ordinates method (SDOM). This method produces anomalies caused by ray effects if radiative boundary conditions have discontinuities or abrupt changes. Ray effects may be mitigated using the modified discrete ordinates method (MDOM), which is based on superposition of the solutions obtained by considering separately radiation from the walls and radiation from the medium. The purpose of this paper is to study the role of ray effects in combined conduction‐radiation problems and investigate the superiority of the MDOM over SDOM.

The MDOM has been used to calculate radiative heat transfer in irregular geometries using body‐fitted coordinates. Here, the blocked‐off region concept, originally developed in computational fluid dynamics, is used along with the finite volume method and SDOM or MDOM to solve combined conduction‐radiation heat transport problems in irregular geometries. Enclosures with an absorbing, emitting and isotropically or anisotropically scattering medium are analyzed.

The results confirm the capability of the MDOM to minimize the anomalies due to ray effects in combined heat transfer problems, and demonstrate that MDOM is more computationally efficient than SDOM.

The paper demonstrates the application of MDOM to combined conduction‐radiation heat transfer problems in irregular geometries using blocked‐off method.

This paper presents a numerical investigation of the interaction of surfaces radiation with developing laminar free convective heat transfer in a divided vertical channel. The influence of the radiation on the heat transfer and on the air flow is studied for various sizes (width and length) of the plate.

The specifically developed numerical code is based on the utilization of the finite volume method. The SIMPLER algorithm for the pressure‐velocity coupling is adopted. The view factors are determined by using boundary elements to fit the surfaces, an algorithm solving the shadow effect and a Monte Carlo method for the numerical integrations.

Results obtained show that the radiation: plays a very important role on the paces of the isotherms, especially at Ra≥1,600; increases considerably the average wall Nusselt number; and increases the mass flow rate and the average channel Nusselt number at high Rayleigh numbers. The plate location has a significant effect on the heat transfer only in presence of the radiation exchange. The increase of both length and width of the plate causes a decrease of the heat transfer and the mass flow rate.

The use of the code is limited to the flow that is assumed to be incompressible, laminar and two dimensional. The radiative surfaces are assumed diffuse‐gray.

Natural convection in vertical channels formed by parallel plates has received significant attention because of its interest and importance in industrial applications. Some applications are solar collectors, fire research, electronic cooling, aeronautics, chemical apparatus, building constructions, nuclear engineering, etc.

In comparison to the most of the previous studies on natural convection in partitioned channels, the radiation exchange was neglected. This study takes into account the radiation exchange in a divided channel.

This paper aims to numerically analyze the effect of non-gray gas radiation on mixed convection in a horizontal circular duct with isothermal partial heating from the sidewall. The influence of heater location on heat transfer, fluid flow and entropy generation is given and discussed in this study.

The numerical computation of heat transfer and fluid flow has been developed by the commercial finite element software COMSOL Multiphysics. Radiation code is developed based on the T₁₀ Ray-Tracing method, and the radiative properties of the medium are computed based on the statistical narrow band correlated-k model.

The obtained results depicted that the radiation considerably contributes to the temperature homogenization of the gas. The findings highlight the impact of the heater location on swirling flow. It is also shown that the laterally heating process provides better energy efficiency than heating from the top of the enclosure.

This study is performed to improve heat transfer and to minimize entropy generation. Therefore, it is conceivable to improve the model design of industrial applications.

This paper numerically investigates the effect of cavity radiation on the thermal response of hollow aluminium tubes and facade systems subjected to fire.

Finite element simulations were performed using ABAQUS 6.14. The accuracy of the numerical model was established through experimental and numerical results available in the literature. The proposed numerical model was utilised to study the effect of cavity radiation on the thermal response of aluminium hollow tubes and facade system. Different scenarios were considered to assess the applicability of the commonly used lumped capacitance heat transfer model.

The effects of cavity radiation were found to be significant for non-uniform fire exposure conditions. The maximum temperature of a hollow aluminium tube with 1-sided fire exposure was found to be 86% greater when cavity radiation was considered. Further, the time to attain critical temperature under non-uniform fire exposure, as calculated from the conventional lumped heat capacity heat transfer model, was non-conservative when compared to that predicted by the proposed simulation approach considering cavity radiation. A metal temperature of 550 °C was attained about 18 min earlier than what was calculated by the lumped heat capacitance model.

The present study will serve as a basis for the study of the effects of cavity radiation on the thermo-mechanical response of aluminium hollow tubes and facade systems. Such thermo-mechanical analyses will enable the study of the effects of cavity radiation on the failure mechanisms of facade systems.

Cavity radiation was found to significantly affect the thermal response of hollow aluminium tubes and façade systems. In design processes, it is essential to consider the potential consequences of non-uniform heating situations, as they can have a significant impact on the temperature of structures. It was also shown that the use of lumped heat capacity heat transfer model in cases of non-uniform fire exposure is unsuitable for the thermal analysis of such systems.

This is the first detailed investigation of the effects of cavity radiation on the thermal response of aluminium tubes and façade systems for different fire exposure conditions.

The purpose of this paper is to investigate the effects of thermal radiation and viscous dissipation on steady natural convection flow of a viscous incompressible fluid along a uniformly moving infinite vertical porous plate with Newtonian heating in the presence of transverse magnetic field. The governing non-linear boundary layer equations are solved by using homotopy analysis method (HAM). The effects of various system parameters on velocity and temperature fields are discussed graphically, and the numerical values for skin friction and Nusselt number are presented in tabular form.

The problem is formulated using the Boussinesq approximation under the effects of thermal radiation and transverse magnetic field. The resulting coupled system of non-linear differential equations is solved using HAM with appropriate boundary conditions for Newtonian heating of the plate. HAM is a powerful method which provides rapidly converging series solution for the velocity and temperature fields. The effects of Prandtl number, Grashof number, suction parameter, magnetic field parameter, radiation parameter and Eckert number on the fluid velocity, temperature, skin friction and Nusselt number have been investigated.

The HAM solution has been successfully applied to find the converging series solution for velocity and temperature fields in terms of pertinent system parameters. Comparison of the exact solution results agree well with the HAM solution results in the absence of Eckert number and this indicates that the HAM solutions are accurate. It is found that the velocity and temperature profiles decreases with the increase of thermal radiation and suction parameters. An increase in the magnetic field parameter leads to a rise in the fluid temperature and fall in the fluid velocity.

The present analysis is limited to steady state laminar natural convection flow only. Unsteady natural- /mixed-convection laminar flow in the presence of thermal radiation, chemical reaction and transverse magnetic field will be investigated in a future work.

The study provides very useful information for heat transfer engineers to understand the heat transfer rate when the moving vertical porous surface temperature is not known a prior. The present results have immediate relevance in the design of nuclear reactors where vertical moving porous plates are using as control rods.

The present research work is relatively original and illustrates the effects of thermal radiation, viscous dissipation and transverse magnetic field on natural convection flow past a uniformly moving infinite vertical porous plate with Newtonian heating.

A two‐dimensional numerical study was carried out to investigate laminar forced‐convection heat transfer characteristics of air flow in a two parallel plate channel with offset plates and heated by a radiation heat flux. The SIMPLE method was used for the numerical prediction of the flow and thermal fields. The flow field temperature boundary conditions were obtained by applying the energy balance equation to boundary elements. The ray tracing technique was used to obtain the net absorbed radiation fractions in the boundary elements. The numerical results were validated with measured temperature values and experimentally calculated values of local Nusselt number (Nu_x), and a reasonable agreement was shown. Then the numerical simulation was used to study effects of design parameters on the convective heat transfer coefficient. It was found that in Re numbers from 650 to 2,550, the optimum spacing of offset plates relative to the nearest channel wall was around one third of the channel height. Also, the optimum offset plates’ numbers can be calculated based on one offset plate length being equal to one and a half times the channel hydraulic diameter. A correlation of average Nusselt number between the flowing air and the offset plates was obtained as follows; —Nu = 1.81 Re ^0.352Pr^1/3(D_h/l)^1/2.