Search results

Despite almost limitless possibilities of rapid prototyping, the idea of 3D printed fully functional electronic device still has not been fulfilled – the missing point is a highly conductive material suitable for this technique. The purpose of this paper is to present the usage of the photonic curing process for sintering highly conductive paths printed on the polymer substrate.

This paper evaluates two photonic curing processes for the conductive network formulation during the additive manufacturing process. Along with the xenon flash sintering for aerosol jet-printed paths, this paper examines rapid infrared sintering for thick-film and direct write techniques.

This paper proves that the combination of fused deposition modeling, aerosol jet printing or paste deposition, along with photonic sintering, is suitable to obtain elements with low resistivity of 3,75·10⁻⁸ Ωm. Presented outcomes suggest the solution for fabrication of the structural electronics systems for daily-use applications.

The combination of fused deposition modelling (FDM) and aerosol jet printing or paste deposition used with photonic sintering process can fill the missing point for highly conductive materials for structural electronics.

The paper aims to present the research results related to transparent heating elements made from carbon nanomaterials. Heating elements were fabricated only with cost-effective techniques with the aim to be easily implemented in large area applications. Presented materials and methods are an interesting alternative to vacuum deposition of transparent resistive layers and etching of low-resistive patterns. Fabricated heating elements were designed to be used as de-icing structures in roof-top windows.

The paper presents the research results related to transparent heating elements made from carbon nanomaterials. Heating elements were fabricated only with cost-effective techniques with the aim to be easily implemented in large area applications. Presented materials and methods are an interesting alternative to vacuum deposition of transparent resistive layers and etching of low-resistive patterns. Fabricated heating elements were designed to be used as de-icing structures in roof-top windows.

The sheet resistance of obtained layers was between 9 and 11 kΩ/□; however, double-walled carbon nanotubes showed significantly higher optical transmission (around 70 per cent) than graphene nanoplatelets (around 55 per cent for visible and near infrared range). The amount of polymer resin had the influence on the paints stability, electrical properties and coatings adhesion.

Results show a novel method of fabrication of a large area and transparent heating elements with tunable resistance done through the change of spray coating paint composition.

The aims of this paper are to investigate the influence of direct current (DC) electric field on separation and orientation of carbon nanotubes (CNTs) in spray-coated layers and apply this method to the fabrication of elastic and transparent electrodes. The orientation of CNTs in the form of paths in the direction of electrical conduction should increase the electrode conductivity without decreasing its optical transmission.

Materials are deposited using vacuum-free, ultra-fine nozzle spray coating technique, easily applicable for large-scale production. After the deposition of carbon nanomaterials, nanoparticles are oriented in the electric field and initially cured with infrared halogen lamp to evaporate solvents and preserve orientation of the nanoparticles in the deposited layer. Afterwards, layers are cured in a chamber dryer to obtain desired properties. Nanoparticles orientation and carbon nanomaterials separation via DC electric field are analysed, and the optical and electrical properties of prepared electrodes are measured.

Experiments described in this paper showed that DC electric field can be applied provide separation and orientation of CNTs and combined with spray coating technique, can be used as additional tool for tuning the conductivity of flexible and transparent electrodes by decreasing the sheet resistance about five times.

The results showed that spray coating combined with electric field orientation is a promising solution of obtaining elastic and transparent electrodes with oriented carbon particles. According to the authors’ knowledge, none of the experiments was directed to obtain DC electric field-oriented transparent layers produced with the use of spray coating technique.

The aim of this paper was to verify applicability of graphene-based sensors for voltammetric and amperometric measurements of low-concentration compounds in biological fluids.

Using the screen printing method, electrochemical sensors were manufactured on polymethylmetacrylate foil using a paste consisting of organic solvents and graphene nanopetals. As the model of a biological fluid tear film was chosen, the compound chosen as the analyte was H₂O₂, which is produced in oxidation of biological compounds. Tear film analog was prepared, in which, the measurements were carried out in a wide range of concentrations to determine the oxidation potential of H₂O₂ through square-wave voltammetry. The second series of amperometric measurements was carried out for concentrations between 0 and 30 μM/L, which is the lower range of physiological glucose concentration in tear films.

The sensors presented linearity for concentrations from 0 to 3.5 per cent. Mean linear correlation coefficient between the peak current and the concentration for the examined sensors was 0.9764. Mean sensitivity was 434.4 mA·M−1·L−1.

Results indicate a need for optimization of the sensors ' performance. Main parameters to be improved are surface area of electrodes and purity of the graphene layer, as well as uniformity of the manufacturing process to improve accuracy and repeatability of measurements.

Technology and materials used present an opportunity for creating low-cost, miniaturized and biocompatible sensors to be used in medical monitoring.

Printed electronics technology described was not investigated previously in the field of biological sensors and could contribute to the solving of vital medicine problems.

New types of substrates were used for fabrication of printed electroluminescent structures. Polymer foils mainly used as substrates for such optoelectronic elements were replaced with paper and textiles. Printing on non-transparent substrate requires elaboration of printed transparent electrode, while usually polyester foils with sputtered ITO transparent electrodes are used. The paper aims to discuss these issues.

Electroluminescent structures were fabricated with elaborated polymer compositions filled with nanomaterials, such as carbon nanotubes and graphene platelets, dielectric and luminophore nanopowders. Structures were printed as “reverse stack”, where transparent electrode is printed on top of the last luminophore layer. For that carbon nanotubes and graphene platelets filled composition was used, deposited with spray-coating technique.

Main issue with new substrates is proper wetting with the use of screen-printing pastes, and much higher roughness especially for textiles.

Fully functional structures were obtained, but several disadvantages were observed that needs to be eliminated in further studies.

The purpose of this paper is to present a proposal for the methodology of developing rescue plans and the concepts of applying recommended response schedules in the context of the State Fire Service’s planning responsibilities (preparation) and public administration (reconciliation and approval), according to the legal order in force in Poland. In the proposed concept, recommended schedules are built on the basis of the matches and successes identified according to the criteria, i.e. the best carried out rescue actions from the register of reports.

The paper is based on the analysis of existing legal status and policy in Poland as well as the selected relevant academic literature.

The result is the formulation of a methodology for drawing up the rescue plans to the extent required by law and proposing a concept for the method of developing and applying recommended response schedules, supporting operational planning and conducting rescue operations.

The proposed methodology is to support the procedure of drawing up rescue plans by implying and implementing them into IT solutions. The suggested recommended response schedules, based on observations and conclusions from the analysis of the past rescue operations, may present circumstances and sequences of the use of forces and measures that have had beneficial effects in the past. An in-depth analysis of historical data from the conducted rescue operations may also be used to determine time indicators for the response phase.

The proposed solutions complement the methods currently used by public administration in Poland. The concept can also be inspiring for the State Fire Service (PSP) which has its own analytical tools in the form of a decision support system and registers of rescue operations carried out. The PSP may undertake the practical verification of the presented methodology for preparing rescue plans and recommended response schedules.