Search results
1 – 10 of 214Ozgur Balli, Alper Dalkıran and Tahir Hikmet Karakoç
This study aims to investigate the aviation, energetic, exergetic, environmental, sustainability and exergoeconomic performances of a micro turbojet engine used in unmanned aerial…
Abstract
Purpose
This study aims to investigate the aviation, energetic, exergetic, environmental, sustainability and exergoeconomic performances of a micro turbojet engine used in unmanned aerial vehicles at four different modes.
Design/methodology/approach
The engine data were collected from engine test cell. The engine performance calculations were performed for four different operation modes.
Findings
According to the results, maximum energy and exergy efficiency were acquired as 19.19% and 18.079% at Mode 4. Total cost rate was calculated as 6.757 $/h at Mode-1, which varied to 10.131 $/h at Mode-4. Exergy cost of engine power was observed as 0.249 $/MJ at Mode-1, which decreased to 0.088 $/MJ at Mode-4 after a careful exergoeconomic analysis.
Originality/value
The novelty of this work is the capability to serve as a guide for similar systems with a detailed approach in the thermodynamic, thermoeconomic and environmental assessments by prioritizing efficiency, fuel consumption and cost formation. This investigation intends to establish a design of the opportunities and benefits that the thermodynamic approach provides to turbojet engine systems.
Details
Keywords
Peyman Maghsoudi, Sadegh Sadeghi, Qingang Xiong and Saiied Mostafa Aminossadati
Because of the appreciable application of heat recovery systems for the increment of overall efficiency of micro gas turbines, promising evaluation and optimization are crucial…
Abstract
Purpose
Because of the appreciable application of heat recovery systems for the increment of overall efficiency of micro gas turbines, promising evaluation and optimization are crucial. This paper aims to propose a multi-factor theoretical methodology for analysis, optimization and comparison of potential plate-fin recuperators incorporated into micro gas turbines. Energetic, exergetic, economic and environmental factors are covered.
Design/methodology/approach
To demonstrate applicability and reliability of the methodology, detailed thermo-hydraulic analysis, sensitivity analysis and optimization are conducted on the recuperators with louver and offset-strip fins using a genetic algorithm. To assess the relationship between investment cost and profit for the recuperated systems, payback period (PBP), which incorporates all the factors is used as the universal objective function. To compare the performance of the recuperated and non-recuperated systems, exergy efficiency, exergy destruction and corresponding cost rate, fuel consumption and environmental damage cost rates, capital and operational cost rates and acquired profit rates are determined.
Findings
Based on the results, optimal PBP of the louvered-fin recuperator (147 days) is slightly lower than that with offset-strip fins (153 days). The highest profit rate is acquired by reduction of exergy destruction cost rate and corresponding decrements for louver and offset-strip fins are 2.3 and 3.9 times compared to simple cycle, respectively.
Originality/value
This mathematical study, for the first time, focuses on introducing a reliable methodology, which covers energetic, exergetic, economic and environmental points of view beneficial for design and selection of efficient plate-fin recuperators for micro gas turbine applications.
Details
Keywords
Abbas Naeimi, Mohammad Hossein Ahmadi, Milad Sadeghzadeh and Alibakhsh Kasaeian
This paper aims to determine the optimum arrangement of a reverse osmosis system in two methods of plug and concentrate recycling.
Abstract
Purpose
This paper aims to determine the optimum arrangement of a reverse osmosis system in two methods of plug and concentrate recycling.
Design/methodology/approach
To compare the optimum conditions of these two methods, a seawater reverse osmosis system was considered to produce fresh water at a rate of 4,000 m3/d for Mahyarkala city, located in north of Iran, for a period of 20 years. Using genetic algorithms and two-objective optimization method, the reverse osmosis system was designed.
Findings
The results showed that exergy efficiency in optimum condition for concentrate recycling and plug methods was 82.6 and 92.4 per cent, respectively. The optimizations results showed that concentrate recycling method, despite a 36 per cent reduction in the initial cost and a 2 per cent increase in maintenance expenses, provides 6 per cent higher recovery and 19.7 per cent less permeate concentration than two-stage plug method.
Originality/value
Optimization parameters include feed water pressure, the rate of water return from the brine for concentrate recycling system, type of SW membrane, feedwater flow rate and numbers of elements in each pressure vessel (PV). These parameters were also compared to each other in terms of recovery (R) and freshwater unit production cost. In addition, the exergy of all elements was analyzed by selecting the optimal mode of each system.
Details
Keywords
Sunday Olayinka Oyedepo, Richard Olayiwola Fagbenle, Samuel Sunday Adefila and Md Mahbub Alam
This study aims to use an environomics method to assess the environmental impacts of selected gas turbine power plants in Nigeria.
Abstract
Purpose
This study aims to use an environomics method to assess the environmental impacts of selected gas turbine power plants in Nigeria.
Design/methodology/approach
In this study, exergoenvironomic analysis has been carried out to investigate the environmental impact of selected gas turbine power plants in Nigeria from an exergetic point of view.
Findings
The exergy analysis reveals that the combustion chamber is the most exergy destructive component compared to other cycle components. The exergy destruction of this component can be reduced by increasing gas turbine inlet temperature (GTIT). The results of the study show that thermodynamic inefficiency is responsible for the environmental impact associated with gas turbine components. The study further shows that CO2 emissions and cost of environmental impact decrease with increasing GTIT.
Originality/value
The exergo-environomic parameters computed in this study are CO2 emission in kg per MWh of electricity generated, depletion number, sustainability index, cost flow rate of environmental impacts (Ċenv) in $/h and total cost rates of products (ĊTot) in $/hr. For the period considered, the CO2 emissions for the selected plants vary from 100.18 to 408.78 kgCO2/MWhm, while cost flow rate of environmental impacts varies from $40.18 /h to $276.97 /h and the total cost rates of products vary from $2935.69/h to $12,232.84/h. The depletion number and sustainability index vary from 0.69 to 0.84 and 1.20 to 1.44, respectively.
Details
Keywords
P. Gunasekar, S. Manigandan, Venkatesh S., R. Gokulnath, Rakesh Vimal and P. Boomadevi
The depletion of fossil fuel and emissions of harmful gases forced the pioneers in search of alternate energy source. The purpose of this study is to present an effective use of…
Abstract
Purpose
The depletion of fossil fuel and emissions of harmful gases forced the pioneers in search of alternate energy source. The purpose of this study is to present an effective use of hydrogen fuel for turbojet engines based on its exergetic performance.
Design/methodology/approach
This study was performed to measure the assessment of exergetic data of turbojet engines. Initially, the test was carried out on the Jet A-1 fuel. Then, a series of similar tests were carried out on turbojet engines with hydrogen fuel to measure their performance results. Finally, the exergetic values of both were compared with each other.
Findings
The introduction of hydrogen fuel reduced the exergy efficiency, and a 10 per cent reduction was observed in exergy efficiency. Simultaneously, the waste exergy rate increased by 9 per cent. However, because of the high specific fuel exergy, hydrogen fuel was better than Jet A-1 fuel. Note that parameters such as environmental effect factor and ecological effect witnessed an increase in their index owing to the addition of hydrogen.
Practical implications
Introduction of alternative blends is necessary for achieving lower emission of gases such as CO, NOx and CO2 from gas turbine engines without compromising on performance. The Jet A fuels were replaced by blends to obtain better emission characteristics.
Originality/value
The use of hydrogen in turbojet engines showed an adverse effect on exergetic performance. However, it was very impressive to see a 200 per cent reduction in emissions. From the comparison of exergy efficiency results of inlet, combustion and nozzle, it is evident that the combustion chamber has the largest values of exergy ratio, waste exergy ratio, cost flow, ecological factor, environmental factor and fuel ratio owing to irreversibility in the combustion process.
Details
Keywords
Taraprasad Mohapatra and Sudhansu Sekhar Mishra
The study aims to verify and establish the result of the most suitable optimization approach for higher performance and lower emission of a variable compression ratio (VCR) diesel…
Abstract
Purpose
The study aims to verify and establish the result of the most suitable optimization approach for higher performance and lower emission of a variable compression ratio (VCR) diesel engine. In this study, three types of test fuels are taken and tested in a variable compression ratio diesel engine (compression ignition). The fuels used are conventional diesel fuel, e-diesel (85% diesel-15% bioethanol) and nano-fuel (85% diesel-15% bioethanol-25 ppm Al2O3). The effect of bioethanol and nano-particles on performance, emission and cost-effectiveness is investigated at different load and compression ratios (CRs). The optimum performance and lower emission of the engine are evaluated and compared with other optimization methods.
Design/methodology/approach
The test engine is run by diesel, e-diesel (85% diesel-15% bioethanol) and nano-fuel (85% diesel-15% bioethanol-25 ppm Al2O3) in three different loadings (4 kg, 8 kg and 12 kg) and CR of 14, 16 and 18, respectively. The optimum value of energy efficiency, exergy efficiency, NOX emission and relative cost variation are determined against the input parameters using Taguchi-Grey method and confirmed by response surface methodology (RSM) technique.
Findings
Using Taguchi-Grey method, the maximum energy and exergy efficiency, minimum % relative cost variation and NOX emission are 24.64%, 59.52%, 0 and 184 ppm, respectively, at 4 kg load, 18 CR and fuel type of nano-fuel. Using RSM technique, maximum energy and exergy efficiency are 24.8% and 62.9%, and minimum NOX emission and % cost variation are 208.4 ppm and –6.5, respectively, at 5.2 kg load, 18 CR and nano-fuel. The RSM is suggested as the most appropriate technique for obtaining maximum energy and exergy efficiency, and minimum % relative cost; however, for lowest possible NOX emission, the Taguchi-Grey method is the most appropriate.
Originality/value
Waste rice straw is used to produce bioethanol. 4-E analysis, i.e. energy, exergy, emission and economic analysis, has been carried out, optimized and compared.
Details
Keywords
Soroush Sadripour, Mohammad Estajloo, Seyed Abdolmehdi Hashemi, Ali J. Chamkha and Mahmoud Abbaszadeh
The purpose of this study is to reduce energy consumption in bakeries. Due to fulfill this demand, quite a few parameters such as energy and exergy efficiency, energy waste and…
Abstract
Purpose
The purpose of this study is to reduce energy consumption in bakeries. Due to fulfill this demand, quite a few parameters such as energy and exergy efficiency, energy waste and fuel consumption by different traditional flatbreads bakeries (Sangak, Barbari, Taftun and Lavash should be monitored and their roles should not be neglected.
Design/methodology/approach
In the present study, experimental measurements and mathematical modeling are used to scrutinize and investigate the effects of the aforementioned parameters on energy consumption by bakeries.
Findings
The results show that by doing reported methods in this paper, the wasted energy of the walls can be decreased by about 65 per cent; and also, by controlling the combustion reaction to perform with 5 per cent excess air, the wasted energy of excess air declines by about 90 per cent. And finally, the energy and exergy efficiency of bakeries is increased, and as a result, the annual energy consumption of Sangak, Barbari, Taftun and Lavash bakeries diminish about 71, 59, 57 and 40 per cent, respectively.
Originality/value
As evidenced by the literature review, it can be observed that neither numerical studies nor experimental investigations have been conducted about energy and exergy analyses of Iranian machinery traditional flatbread bakeries. It is clear that due to a high preference of Iranians to use the traditional bread and also the popularity of baking this kind of bread in Iran, if it is possible to enhance the traditional oven conditions to decrease the loss of natural gas instead of industrializing the bread baking, the energy consumption in the country can be optimized.
Details
Keywords
Manish Kumar, Arun Arora, Raghwendra Banchhor and Harishankar Chandra
This paper aims to analyze energy and exergy analysis of solar-based intercooled and reheated gas turbine (GT) trigeneration cycle using parabolic trough solar collectors (PTC…
Abstract
Purpose
This paper aims to analyze energy and exergy analysis of solar-based intercooled and reheated gas turbine (GT) trigeneration cycle using parabolic trough solar collectors (PTC) with the use of MATLAB 2018.
Design/methodology/approach
In the first section of this paper, the solar-based GT is validated with the reference paper. According to the reference paper, the solar field is comprising 30 modules in series and 35 modules in parallel series, where a total of 1,050 modules of PTC are taken into consideration. In the second part of this paper, the hybridization of the solar, GT trigeneration cycle is analyzed and optimized. In the last section of this paper, the hybridization of solar, intercooled and reheated GT trigeneration systems is examined and compared.
Findings
The results examined the first section, the power produced by the cycle will be 37.34 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and the efficiencies of energy and exergy will be 38.34% and 39.76%, respectively. The results examined in the second section, the power produced by the cycle will be 38.4 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and accordingly the efficiency of energy and exergy is found to be 40.011% and 41.763%. Where in the last section, the power produced by the cycle will be 41.43 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and the energy and exergy efficiencies will be 39.76% and 40.924%, respectively.
Originality/value
The author confirms that this study is original and has neither been published elsewhere nor it is currently under consideration for publication elsewhere.
Details
Keywords
Ranga Babu J.A., Kiran Kumar K. and Srinivasa Rao S.
This paper aims to present an analytical investigation of energy and exergy performance on a solar flat plate collector (SFPC) with Cu-CuO/water hybrid nanofluid, Cu/water and…
Abstract
Purpose
This paper aims to present an analytical investigation of energy and exergy performance on a solar flat plate collector (SFPC) with Cu-CuO/water hybrid nanofluid, Cu/water and CuO/water nanofluids as collector running fluids.
Design/methodology/approach
Heat transfer characteristics, pressure drop and energy and exergy efficiencies of SFPC working on these nanofluids are investigated and compared. In this study, a comparison is made by varying the mass flow rates and nanoparticle volume concentration. Thermophysical properties of hybrid nanofluids are estimated using distinctive correlations available in the open literature. Then, the influence of these properties on energy and exergy efficiencies of SFPC is discussed in detail.
Findings
Energy analysis reveals that by introducing the hybrid nanoparticles in water, the thermal conductivity of the working fluid is enhanced by 17.52 per cent and that of the individual constituents is enhanced by 15.72 and 15.35 per cent for Cu/water and CuO/water nanofluids, respectively. This resulted in 2.16 per cent improvement in useful heat gain for hybrid nanofluid and 1.03 and 0.91 per cent improvement in heat gain for Cu/water and CuO/water nanofluids, respectively. In line with the above, the collector efficiency increased by 2.175 per cent for the hybrid nanofluid and 0.93 and 1.05 per cent enhancement for Cu/water and CuO/water nanofluids, respectively. Exergy analysis elucidates that by using the hybrid nanofluid, exergy efficiency is increased by 2.59 per cent, whereas it is 2.32 and 2.18 per cent enhancement for Cu/water and CuO/water nanofluids, respectively. Entropy generation is reduced by 3.31, 2.35 and 2.96 per cent for Cu-CuO/water, Cu/water and CuO/water nanofluids, respectively, as compared to water.
Research limitations/implications
However, this is associated with a penalty of increment in pressure drop of 2.92, 3.09 and 2.74 per cent for Cu-CuO/water, Cu/water and CuO/water nanofluids, respectively, compared with water.
Originality/value
It is clear from the analysis that Cu-CuO/water hybrid nanofluids possess notable increment in both energy and exergy efficiencies to use them in SFPCs.
Details
Keywords
The purpose of this study is to perform an exergy analysis of a turbojet engine combustor at different cycle parameters.
Abstract
Purpose
The purpose of this study is to perform an exergy analysis of a turbojet engine combustor at different cycle parameters.
Design/methodology/approach
Base cycle parameters have been defined for the engine, and then differentiation of the combustor exergy efficiencies and destruction rates have been evaluated by changing overall pressure ratio, combustor exit temperature and combustor pressure ratio.
Findings
For the basic engine cycle, combustor unit is found to have lowest exergy efficiency as 62.3 for the sea level static condition. Compressor turbine exhaust and whole engine exergy efficiencies have been calculated as 88.7, 96.5, 68.2 and 69.4, respectively.
Practical implications
Because of the biggest exergy, destruction is seen mainly in combustion system; effect of the combustor inlet pressure (related to the compressor design technology), pressure drop and exit temperature on the exergy efficiencies have been analyzed and combustor second law efficiency have been evaluated.
Social implications
The investigation’s purposes are highly connected with social wellness and targeted at sustainable development of the society. Practical implementation of the obtained scientific results is directed on the improving of combustor for a turbojet engines and decreasing negative influence on the environment.
Originality/value
As a result of this paper, the following are the contribution of this paper in the field of gas turbine exergy subjects: Combustor has been found as the most critical component in respect of the exergy efficiency. Therefore, the effect of the combustor main cycle parameters such as inlet pressure, combustor pressure ratio and exit temperature have been analyzed.
Details