Search results

In electrical discharge machining (EDM) process, the production of separate electrodes for rough, semi‐rough and finish machining of dies and moulds having complex surfaces, results in high cost and long lead‐time in manufacturing. The purpose of this paper is to describe the machining performance of electrodes formed by using copper wire bunches (WBs) positioned to conform the surface to be machined was experimentally and theoretically analyzed. In the study, the variations in the machining rate, electrode wear rate, relative wear and workpiece surface roughness were examined for various discharge current and pulse‐time settings.

Copper WBs positioned to conform the surface to be machined in electric discharge machining. The variations in the machining rate, electrode wear rate, relative wear and workpiece surface roughness were examined experimentally for various discharge current and pulse‐time settings. The WB electrodes (WBEs) are proven to be satisfactory as electrodes for roughing operations in electric discharge machining.

The increase in number of wires and pulse energy result in decrease of relative wear for each wire in the electrode. The increase in number of wires in electrodes causes increase in machining area and in machining time in WBE method. With the increase of discharge current and pulse time, the electrode wear rate and material removal values increase and machining time decreases. By using the mathematical models obtained from the result of the experiments, the electrode wear rate, material removal rate, relative wear and the set length of wires for the desired cavity profile can be calculated. The labor cost of electrode manufacturing in the WBE method is lower compared to conventional solid electrodes. The use of WBE method for rough machining decreases machining cost and time. The use of WBE method decreases both the number of the electrodes required and the delay in starting machining due to the preparation of electrode in EDM.

This paper introduces the benefits of using WBE in electric discharge machining; wear and material removal characteristics of WBEs are introduced; the surface roughness characteristics of surfaces produced by WBEs are examined experimentally; and the effect of number of wires used in WBEs given (experimental findings).

This paper aims to present the performance of deionized water in electrical discharge machining (EDM) during machining of Inconel 718, copper tool electrode and deionized water as dielectric. Three parameters, namely, pulse-on-time, pulse-off-time and discharge current were taken as control parameters with individual parameter having three levels. Influence of these control parameters on response such as tool wear rate (TWR), material removal rate (MRR) and surface roughness (Ra) is evaluated at various combinations of parametric levels. The results reveal deionized water can be effectively used as a sustainable dielectric and may substitute the hydrocarbon-based dielectric in electrical discharge machining. Also, the control parameters considered show significant impact on the process criteria. Super ranking method was adopted to achieve optimal integration of EDM control factors for obtaining higher MRR, lower TWR and Ra. Further, by applying analysis of variance test, discharge current is established as the dominant parameter during the machining process.

The experimentation was performed on Inconel 718 in SPARKONIX MOS, 35 A, ZNC EDM using deionized water as dielectric and copper tool as electrode. The dielectric circulatory system was developed without disturbing the existing dielectric circulation system. Figure 1 shows the EDM with newly developed dielectric system. The existing system consists of hydrocarbon-based dielectric, which has a number of drawbacks during the machining such as carbide deposition on the work material, which reduces removal of material from work material; carbon particle adhesion on tool, which results in inefficient discharge between the electrode; and the work material and production of CO and CH4 during machining, which makes the machining environment toxic. To overcome these drawbacks, a sustainable dielectric was adopted in present work. Trial experiments were conducted to select the ranges of parameters, namely, discharge current, pulse-on-time and pulse-off-time. The process characteristics were evaluated at different parametric combinations and the experimentation was designed as per Taguchi L9 orthogonal array. Table 1 shows the properties of Inconel 718. Table 2 shows the parameters considered with its ranges. Table 3 shows the experimental values. The difference of weight of work piece before and after was taken and divided by the machining time used for calculating the MWR. Similarly, the difference of weight of tool material before and after was taken and divided by machining time and is used for calculating TWR. Measurement of surface roughness was done using Talysurf surface roughness meter.

The experimentation was conducted at different parametric combination on Inconel 718 taking copper as electrode and deionized water as dielectric. The performance criteria was evaluated at considered parametric combination. The result shows that the EDM parameters have significant contribution on the performance criteria and deionized water can be effectively used as dielectric medium in EDM. The use of deionized water as dielectric will improve the process and sustainable green machining can be performed. Super ranking method has been implemented to achieve the best combination of control factors and it is obtained that the combination A1B1C3 (i.e. discharge current = 3 A, pulse-on-time = 1 µs and pulse-off-time = 3 µs) is best combination for obtaining the higher MRR and lower TWR and Ra. The contributing factor in the proposed research work is discharge current. Further, ANOVA was implemented to check the adequacy of these result. It was established that discharge current is the most influential factor followed by pulse-on-time and the least contributing factor as pulse-off-time. The findings of this paper may open the guidelines for researcher for performing research in the field of sustainable machining of difficult to cut materials such as Inconel 718 with sustainable dielectrics in engineering applications.

The paper is original in nature. The findings of this paper may open the guidelines for researcher for performing research in the field of sustainable machining.

This study aims to understand the current production scenario emphasizing the significance of green manufacturing in achieving economic and environmental sustainability goals to fulfil future needs; to determine the viability of particular strategies and actions performed to increase the process efficiency of electrical discharge machining; and to uphold the values of sustainability in the nonconventional manufacturing sector and to identify future works in this regard.

A thorough analysis of numerous experimental studies and findings is conducted. This prominent nontraditional machining process’s potential machinability and sustainability challenges are discussed, along with the current research to alleviate them. The focus is placed on modifications to the dielectric fluid, choosing affordable substitutes and treating consumable tool electrodes.

Trans-esterified vegetable oils, which are biodegradable and can be used as a substitute for conventional dielectric fluids, provide pollution-free machining with enhanced surface finish and material removal rates. Modifying the dielectric fluid with specific nanomaterials could increase the machining rate and demonstrate a decrease in machining flaws such as micropores, globules and microcracks. Tool electrodes subjected to cryogenic treatment have shown reduced tool metal consumption and downtime for the setup.

The findings suggested eco-friendly machining techniques and optimized control settings that reduce energy consumption, lowering operating expenses and carbon footprints. Using eco-friendly dielectrics, including vegetable oils or biodegradable dielectric fluids, might lessen the adverse effects of the electrical discharge machine operations on the environment. Adopting sustainable practices might enhance a business’s reputation with the public, shareholders and clients because sustainability is becoming increasingly significant across various industries.

A detailed general review of green nontraditional electrical discharge machining process is provided, from high-quality indexed journals. The findings and results contemplated in this review paper can lead the research community to collectively apply it in sustainable techniques to enhance machinability and reduce environmental effects.

This paper aims to study the breakdown, oscillation and vanishing of the discharge channel and its influence on crater formation with simulation and experimental methods. The experiment results verified the effect of the oscillating characteristics of the discharge channel on the shape of the crater.

A mathematical model that considers the magnetohydrodynamics (MHD) and the discharge channel oscillation was established. The micro process of discharging based on magnetic-fluid coupling during electrical discharge machining (EDM) was simulated. The breakdown, oscillation and vanishing stage of the discharge channel were analyzed, and the crater after machining was obtained. Finally, a single-pulse discharge experiment during EDM was conducted to verify the simulation model.

During the breakdown of the discharge channel, the electrons move towards the center of the discharge channel. The electrons at the end diverge due to the action of water resistance, making the discharge channel appear wide at both ends and narrow in the middle, showing the pinch effect. Due to the mutual attraction of electrons and positive ions in the channel, the transverse oscillation of the discharge channel is shown on the micro level. Therefore, the position of the discharge point on the workpiece changes. The longitudinal oscillation in the discharge channel causes the molten pool on the workpiece to be ejected due to the changing pressure. The experimental results show that the shape of the crater is similar to that in the simulation, which verifies the correctness of the simulation results and also proves that the crater generated by the single pulse discharge is essentially the result of the interaction between transverse wave and longitudinal wave.

In this paper, the simulation of the discharge breakdown process in EDM was carried out, and a new mathematical model that considers the MHD and the discharge channel oscillation was established. Based on the MHD module, the discharge breakdown, oscillation and vanishing stages were simulated, and the velocity field and pressure field in the discharge area were obtained.

The purpose of this paper is to represent the innovative process of powder-mixed electrical discharge machining of high-speed steel T1 grade and to conduct experimental investigation to optimize the machining parameters associated with multiple performance characteristics using grey relational analysis. The machining of high-speed steel T1 grade via conventional machining is a difficult process. However, it can be easily machined by powder-mixed electric discharge machining.

Carefully selected machining parameters give the optimum output results. For experimentation, the following input parameters have been used: pulse on-time, discharge current, tool material and powder concentration. The effects of input parameters, namely, material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR), have been investigated in this research.

Grey relational analysis and analysis of variance have been performed to optimize the input parameters for better output response. Optimized results show increment of TWR, MRR and SR, which is 63.24, 52.18 and 42.49 per cent, respectively.

This research paper will be beneficial for the industrial application. The GRA result gives the better output response.

The purpose of this study is to explore the machining characteristics of electrical discharge machining (EDM) when a tool is fabricated using powder metallurgy. Because pure Cu tools obtained using conventional machining pose problems of high tool wear rate, tool oxidation causes loss of characteristics in tool shape.

The research investigation carried out experiments planned through Taguchi’s robust design of experiments and used analysis of variance (ANOVA) to carry out statistical analysis.

It has been found that copper and chromium electrodes give less metal removal rate as compared to the pure Cu tool. Analytical outcomes of ANOVA demonstrated that MRR is notably affected by the variable’s polarity, peak current, pulse on time and electrode type in the machining of EN9 steel with EDM, whereas the variables pulse on time, gap voltage and electrode type have a significant influence on EWR. Furthermore, the process also showed that the use of powder metallurgy tool effectively reduces the value of SR of the machined surface as well as the tool wear rate. The investigation exhibited the possibility of the use of powder metallurgy electrodes to upgrade the machining efficiency of EDM process.

There is no major limitation or implication of this study. However, the composition of the powders used in powder metallurgy for the fabrication of tools needs to be precisely controlled with careful control of process variables during subsequent fabrication of electrodes.

To the best of the authors’ knowledge, this is the first study that investigates the effectiveness of copper and chromium electrodes/tools fabricated by means of powder metallurgy in EDM of EN9 steel. The effectiveness of the tool is assessed in terms of productivity, as well as accuracy measures of MRR and surface roughness of the components in EDM machining.

The electric discharge machining (EDM) involves electrons discharged from the electrode and machining progresses due to the removal of the material from the component. This a thermal-based machining process primarily used for hard to machine components with conventional methods. This process is used to make intricate cavities and contours. The fabricated part is the replica of the tool material with high surface finish and good dimensional accuracy. This study aims to evaluate the comprehensive effect of process parameters on electric discharge machining of maraging steel.

Multiple criteria Decision making (MCDM) techniques are used to select the best parameters by comparing several responses to achieve the desired goal. There are different MCDM techniques available for optimization of machining parameters. In the current investigation, multi-objective optimization by data envelopment analysis based ranking (DEAR) approach was used for machining Maraging C300 grade steel.

The Taguchi L9 runs were planned with process parameters such as current (Amp), Tool diameter (mm) and Dielectric pressure (MPa). The effect of process parameters on the responses, namely, material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR) were evaluated. High MRR is found at 15 A current, 14 mm tool diameter and dielectric pressure of 0.2 MPa. Optimum process parameters experiment showed reduced crack density.

An effort was made successfully to enhance the responses using the DEAR method and establish the decision making of selecting the optimal parameters by comparing the results obtained by machining maraging steel C300 grade.

The purpose of this paper is to investigate the performance of powder-mixed electric discharge machining (PMEDM) using three different powders which are aluminium (Al), silicon carbide (SiC) and aluminium oxide (Al₂O₃). Besides that, the influence of different tool materials was also studied in this experimental investigation. Hence, the work material selected for this purpose was AISI P20 steel and tool materials were copper, brass and tungsten. The performance measures considered in this work were material removal rate (MRR), tool wear rate and radial over cut (ROC).

The process variables considered in this study were powder types, powder concentration, tool materials, peak current and pulse on time. The experimental design, based on Taguchi’s L₂₇ orthogonal array, was adopted to conduct experiments. Significant parameters were identified by performing the analysis of variance on the experimental data.

Based on the analysis of results, it was observed that copper tool combined with Al powder produced maximum MRR (58.35 mm³/min). Similarly, the Al₂O₃ powder combined with tungsten tool has resulted least ROC (0.04865 mm). It was also observed that wear rate of tungsten tool was very low (0.0145 mm³/min).

The experimental investigation of PMEDM involving three different powders (Al, SiC and Al₂O₃) was not attempted before. Moreover, the study of influence of different tool materials (Cu, brass and W) together with the different powders on the electric discharge machining performance was very limited.

This study aims to focus on experimenting the performance of aluminum (Al) powder mixed electric discharge machining (PMEDM) of two different materials viz plastic mould die steel (AISI P20) and nickel-based super alloy (Nimonic 75). This experimental study also focuses on using three different tool materials such as copper, brass and tungsten to analyze their influence on the process output. These materials find many uses in industrial as well as aerospace applications. The performance measures considered in this work are material removal rate (MRR), tool wear rate (TWR) and surface roughness (SR).

The experimental design used in this work is based on Taguchi’s L18 orthogonal array. Besides considering work and tool material as one of the process variables, other process variables are peak current (I_p), pulse on time (T_on) and concentration of powder (C_p). The analysis of variance (ANOVA) is performed on the experimental data to determine the significant variables that influence the output.

It is found that copper produced maximum MRR and brass tool exhibited higher TWR. However, the surface finish of the machined work piece was very much improved by using the brass tool. Though the performance of tungsten tool lies between the above two tool materials, it showed very little wear during EDM with or without the addition of Al powder.

The experimental investigation of PMEDM of nickel-based super alloy (Nimonic 75) has not been attempted before. Besides that, the study on the influence of tungsten tool on the performance of EDM is also very limited.

This study aims to explore the machinability of ZrB₂ using electrical discharge machining (EDM) with different tool materials.

The workpiece for this study was fabricated through powder metallurgy compaction method. The disc is machined using diamond load grinding to have parallel surfaces, then, 2 mm diameter holes are machined on the disc using EDM spark erosion machine with different tool materials (graphite, aluminium, tantalum, niobium, copper, brass, silver, tungsten and titanium). Roundness, geometry of hole, and diameter of the hole at different diametric planes, surface roughness (SR), material removal rate (MRR), tool wear rate (TWR), taper angle and recast layer (RCL) thickness are measured. The photographic analysis of tools, holes in the top view, bottom view and sectional view. SEM analysis was conducted to study the recast layer. Desirability function analysis was employed to rate the performances of tools.

A new theory is developed which relates recast layer thickness with melting point and thermal conductivity of the tool materials. Machining of ZrB₂ by EDM is feasible; graphite is identified as the best tool. Recast layer thickness of the machined surfaces are indirectly proportional to the product of melting point and thermal conductivity of tool. Ablation behaviour of ceramic workpiece lead additional material losses in the tool.

Extremely high strength and hardness of ZrB₂ due to the coexistence of strong covalent and metallic bond make mechanical machining very difficult or even impossible. No machinability studies were conducted previously on ZrB₂ using EDM; this work reveals machinability study of ZrB₂ with different tool materials.