Search results

The purpose of this paper is to examine the coupled heat and mass transport of different shaped porous moist objects in a rectangular channel under the effects of convective drying. Numerical simulations were performed under turbulent conditions for cylindrical, triangular and rectangular shaped different food products in a two-dimensional channel.

Finite element method was used for the unsteady problem and, effects of drying air velocity (AV) and temperature on transport mechanism were evaluated. Three different food materials were used for the circular shaped object and drying performance of the products under different conditions was compared.

Results showed that, changing the air temperature has an important effect on drying for all shaped objects and all materials. The same effect was seen for the AV as, increasing the velocity had positive effects on drying. Two identical objects were placed in the channel one behind the other, and this configuration showed that location of the object in the channel is also important for drying. The moisture content in the object at the front is lower than in the object behind at the end of drying.

This paper can provide technical support to optimize drying performance in the industry with comprehensive data for the process.

The effect of spinning has been studied and analysed for different projectile shapes such as ogive, blunt, cylindrical and conical by using numerical simulations.

Projectile shape is one of the important parameters in the penetration mechanism. The present study deals with the failure mechanisms and ballistic evaluation for different nose-shaped projectiles undergoing normal impact with spinning. Materials characterization has been made by Johnson–Cook strength and failure models, and LS-DYNA simulations are used to analyse the impact of steel projectiles on an Al 7075-T651 target at different impact velocities under normal impact conditions. The experimental results from the literature are used to validate the model. Based on the residual velocity values, the Recht-Ipson model has been curve-fitted and approximate ballistic limit velocity has been evaluated. The approximated ballistic limit velocity is found to be 3.4% higher than the experimental results and compared well with the experimental results. Subsequently, the validated model conditions are used to study and analyse the effect of spinning for different nose-shaped projectiles undergoing normal impact conditions.

The ductile hole failure is observed for the ogive nose projectile, petals are formed and fragmented for the conical projectile, and plugging is observed for cylindrical projectiles. A Recht-Ipson curve is presented for each spinning condition for each projectile shape and the ballistic limit has been evaluated for each condition.

The proposed research outputs are original and innovative and, have a lot of importance in defence applications, particularly in arms and ammunition.

This study aims to investigate the impact of different heater geometries (flat, rectangular, semi-elliptical and triangular) on hybrid nanofluidic (Cu–Al₂O₃–H₂O) convection in novel umbrella-shaped porous thermal systems. The system is top-cooled, and the identical heater surfaces are provided centrally at the bottom to identify the most enhanced configuration.

The thermal-fluid flow analysis is performed using a finite volume-based indigenous code, solving the nonlinear coupled transport equations with the Darcy number (10^–5 ≤ Da ≤ 10^–1), modified Rayleigh number (10 ≤ Ra_m ≤ 10⁴) and Hartmann number (0 ≤ Ha ≤ 70) as the dimensionless operating parameters. The semi-implicit method for pressure linked equations algorithm is used to solve the discretized transport equations over staggered nonuniform meshes.

The study demonstrates that altering the heater surface geometry improves heat transfer by up to 224% compared with a flat surface configuration. The triangular-shaped heating surface is the most effective in enhancing both heat transfer and flow strength. In general, flow strength and heat transfer increase with rising Ra_m and decrease with increasing Da and Ha. The study also proposes a mathematical correlation to predict thermal characteristics by integrating all geometric and flow control variables.

The present concept can be extended to further explore thermal performance with different curvature effects, orientations, boundary conditions, etc., numerically or experimentally.

The present geometry configurations can be applied in various engineering applications such as heat exchangers, crystallization, micro-electronic devices, energy storage systems, mixing processes, food processing and different biomedical systems (blood flow control, cancer treatment, medical equipment, targeted drug delivery, etc.).

This investigation contributes by exploring the effect of various geometric shapes of the heated bottom on the hydromagnetic convection of Cu–Al₂O₃–H₂O hybrid nanofluid flow in a complex umbrella-shaped porous thermal system involving curved surfaces and multiphysical conditions.

Understanding costumer requirements is a precondition for clothing design and manufacturing. A good shapewear designer should know women’s preferences for their buttock shapes before making patterns. The purpose of this paper is to figure out factors affecting the beauty of women’s buttock shapes and the effect of ethnic background to buttock shapes preference.

The approach utilized both 3D virtual models and 3D printed models to detect women’s preference for their buttock shapes. As a first stage, a two-step K-means cluster method was used to classify female buttock shapes into ten groups and these ten kinds of buttock shapes were output as 3D virtual models and printed out as 3D plastic models. In a subsequent stage, 51 Caucasians, 35 African-Americans and 49 Asians were selected to rank the models separately based on their preference and choose the factors which they thought could influence the beauty of buttock shapes. Kendall’s W coefficient was tested to help assessing the ranking results. Finally, a sample girdle was designed based on the buttock shape preferences of Asian females as an example, and was tested by a model.

Results showed some correlation between ethnicity and buttock shape preference. Both methods of presentation of the shapes were equally preferred by participants. Caucasian women preferred a full, round buttock shape, which was coordinated to other parts of the body. The attractive buttock shape as judged by Asian women was curvy, not drooping and not too big. African-American women choose buttock shapes that were very full with high buttock bumps as beautiful. A sample girdle was made based on the preferences of Asian females and it proved to perform well in creating the desired shape during the trial test.

Current research in the literature about women’s buttock beauty is based on plastic surgeons’ experiences. This study provides a novel method to analyze female’s preference for their buttock shapes; a method that can also be used for other body parts. The results can also be used as an indicator for underwear designers to improve shapewear pattern designs and for consumers to evaluate the shaping ability of shapewear.

The aim of this paper is to advance the understanding of the droplet deposition process to better predict and control the manufacturing results for ink-jet deposition.

As material interface has both geometric and physical significance to manufacturing, the approach the authors take is to study the interface evolution during the material joining process in ink-jet deposition using a novel shape metric and a previously developed powerful simulation tool. This tool is an experimentally validated numerical solver based on the combination of the lattice Boltzmann method and the phase-field model that enabled efficient simulation of multiple-droplet interactions in three dimensions.

The underlying physics of two-droplet interaction is carefully examined, which provides deep insights into the effects of the printing conditions on the interface evolution of multiple-droplet interaction. By studying line printing, it is found that increasing impact velocity or decreasing fluid viscosity can reduce manufacturing time. For array printing, the authors have found the issue of air bubble entrapment that can lead to voids in the manufactured parts.

The array of droplets impinges simultaneously, in contrast to most ink-jet printers. Sequential impingement of lines of droplet needs to be studied. Also, impingement on non-planar surfaces has not been investigated yet, but is important for additive manufacturing. Finally, it is recognized that the droplet hardening mechanisms need to be incorporated in the simulation tool to predict and control the final shape and size of the arbitrary features and manufacturing time for ink-jet deposition.

The research findings in this paper imply opportunities for optimization of printing conditions and print head design. Furthermore, if precise droplet control can be achieved, it may be possible to eliminate the need for leveling roller in the current commercial printers to save machine and manufacturing cost.

This work represents one of the first attempts for a systematic study of the interface dynamics of multiple-droplet interaction in ink-jet deposition enabled by the novel shape metric proposed in the paper and a previously developed numerical solver. The findings in this paper advanced the understanding of the droplet deposition process. The physics-based approach of analyzing the simulation results of the interface dynamics provides deep insights into how to predict and control the manufacturing relevant outcomes, and optimization of the deposition parameters is made possible under the same framework.

The purpose of the paper is to predict the erosion rate of the components of centrifugal pump under certain operating condition to identify the maximum erosion area and to discuss the factors affecting them. This helps to optimize design and estimate service life.

In the paper, the Eulerian–Lagrangian approach method coupled with the erosion model to investigate the mixed sand characteristics on erosion characteristics of centrifugal pump flow-through wall. The hydraulic performance and wear characteristics experiment of the pump is used to verify the accuracy of the numerical simulation.

The blade erosion area mainly occurs near the blade inlet and the trailing edge of the pressure surface, the main erosion area of the impeller back shroud is near the outlet of the flow passage and the main erosion area of the volute is near the tongue and the I section. With the change of the average diameter and density of sand particles, the average erosion rate on different flow-through walls is positively correlated with the average mass concentration to a certain extent. However, for different sand shape factors, there is little correlation between the average erosion rate and the average mass concentration. In addition, compared with other erosion areas, the increase of average sand particle diameter and density has the greatest impact on the total erosion rate of blade pressure surface, while the shape of sand particles has a greater impact on the total erosion rate of each flow-through wall of centrifugal pump.

In this work, according to the characteristics of the mixed distribution of different sand diameters in the Yellow River Basin, the erosion characteristics of centrifugal pumps used in the Yellow River Basin are studied. The numerical calculation method for predicting the wall erosion of centrifugal pump is established and compared with the experimental results. The results can provide reference for optimizing design and increasing service life.

One of the major challenges in the design of thermal equipment is to minimize the entropy production and enhance the thermal dissipation rate for improving energy efficiency of the devices. In several industrial applications, the structure of thermal device is cylindrical shape. In this regard, this paper aims to explore the impact of isothermal cylindrical solid block on nanofluid (Ag – H₂O) convective flow and entropy generation in a cylindrical annular chamber subjected to different thermal conditions. Furthermore, the present study also addresses the structural impact of cylindrical solid block placed at the center of annular domain.

The alternating direction implicit and successive over relaxation techniques are used in the current investigation to solve the coupled partial differential equations. Furthermore, estimation of average Nusselt number and total entropy generation involves integration and is achieved by Simpson and Trapezoidal’s rules, respectively. Mesh independence checks have been carried out to ensure the accuracy of numerical results.

Computations have been performed to analyze the simultaneous multiple influences, such as different thermal conditions, size and aspect ratio of the hot obstacle, Rayleigh number and nanoparticle shape on buoyancy-driven nanoliquid movement, heat dissipation, irreversibility distribution, cup-mixing temperature and performance evaluation criteria in an annular chamber. The computational results reveal that the nanoparticle shape and obstacle size produce conducive situation for increasing system’s thermal efficiency. Furthermore, utilization of nonspherical shaped nanoparticles enhances the heat transfer rate with minimum entropy generation in the enclosure. Also, greater performance evaluation criteria has been noticed for larger obstacle for both uniform and nonuniform heating.

The current numerical investigation can be extended to further explore the thermal performance with different positions of solid obstacle, inclination angles, by applying Lorentz force, internal heat generation and so on numerically or experimentally.

A pioneering numerical investigation on the structural influence of hot solid block on the convective nanofluid flow, energy transport and entropy production in an annular space has been analyzed. The results in the present study are novel, related to various modern industrial applications. These results could be used as a firsthand information for the design engineers to obtain highly efficient thermal systems.

This paper aims to clarify the relationship between mechanical behaviors and the underlying geometry of periodic cellular structures. Particularly, the answer to the following research question is investigated: Can seemingly different geometries of the repeating unit cells of periodic cellular structure result in similar functional behaviors? The study aims to cluster the geometry-functional behavior relationship into different categories.

Specifically, the effects of the geometry on the compressive deformation (mechanical behavior) responses of multiple standardized cubic periodic cellular structures (CPCS) at macro scales are investigated through both physical tests and finite element simulations of three-dimensional (3D) printed samples. Additionally, these multiple CPCS can be further nested into the shell of 3D models of various mechanical domain parts to demonstrate the influence of their geometries in practical applications.

The paper provides insights into how different CPCS (geometrically different unit cells) influence their compressive deformation behaviors. It suggests a standardized strategy for comparing mechanical behaviors of different CPCS.

This paper is the first work in the research domain to investigate if seemingly different geometries of the underlying unit cell can result in similar mechanical behaviors. It also fulfills the need to infill and lattify real functional parts with geometrically complex unit cells. Existing work mainly focused on simple shapes such as basic trusses or cubes with spherical holes.

The purpose of this study is to enhance the thermal performance in the labyrinth channel by different ribs shape. The labyrinth channel is a relatively new cooling structure to decrease the temperature near the trailing region of gas turbine.

Based on the geometric similarity, a simplified geometric model is used. The k − ω turbulence model is used to close the Navier–Stokes equations. Five rib shapes (one rectangular rib, two arched ribs and two trapezoid ribs) and five Reynolds numbers (10,000 to 50,000) are considered. The Nusselt number, flow structure and friction factor are analyzed.

Nusselt number is tightly related to the rib shape in the labyrinth channel. The different shapes of the ribs result in different horseshoe vortex and wake region. In general, the arched rib brings the highest Nusselt number and friction factor. The Nusselt number is increased by 15.8 per cent compared to that of trapezoidal ribs. High Nusselt number is accompanied by the high friction factor in a labyrinth channels. The friction factor is increased by 64.6 per cent compared to rectangular ribs. However, the rib shape has a minor effect on the overall thermal performance.

This study is useful to protect the trailing region of advanced gas turbine.

This paper presents the flow structure and heat transfer characteristics in a labyrinth channel with different rib shapes.

Various designs of corrugated webs include trapezoidal, sinusoidal, triangular and rectangular profiles. The increasing use of curved plates has prompted the creation of I-sections made of steel with a corrugated web design. This study aims to examine the effectiveness of an I-beam steel section that features a perforated-triangular web profile.

In the current study, finite element analysis was conducted on corrugated-perforated steel I-sections using ANSYS software. The study focused on inspecting the design of the perforations, including their shape (circle, square, hexagon, diamond and octagon), size of perforations (80 mm, 100 mm and 120 mm) and layout (the position of web perforation), as well as examining the geometric properties of the section in term of bending, lateral torsional buckling, torsion and shear behavior.

The study revealed that perforations with diamond, circle and hexagon shapes exhibit good performance, whereas the square shape performs poorly. Moreover, the steel section’s performance decreases with an increase in perforation size, regardless of loading conditions. In addition, the shape of the web perforations can also influence its stress distribution. For example, diamond-shaped perforations have been found to perform better than square-shaped perforations in terms of stress distribution and overall performance. This was because of their ability to distribute stress more evenly and provide greater support to the surrounding material. The diagonal alignment of the diamond shape aligns with principal stress directions, allowing for efficient load transfer and reduced stress concentrations. Additionally, diamond-shaped perforations offer a larger effective area, better shear transfer and improved strain redistribution, resulting in enhanced structural integrity and increased load-carrying capacity.

Hence, the presence of lateral-torsional buckling and torsional loading conditions significantly impacts the performance of corrugated-perforated steel I-sections.