Search results

The purpose of this paper is to study the introduction of 3D-printing of concrete in the construction sector.

A survey was conducted to collect professional view on ongoing innovations in the construction sector, including 3D-printing. Participants were selected among the members of Norwegian networks for project and construction management research.

The survey highlighted effective leadership, collaboration with partners and industry-academia collaboration as primary enablers of innovation. Few of the respondents to the survey have used 3D-printing technologies.

It is difficult to obtain representative samples in this type of research, including this study. The study can be seen as a snapshot of attitudes in the sector.

3D-printing appear as a potentially interesting technology, especially for unstandardized construction components. Further work is needed to materialise the expectation for technological development in the construction sector.

Most research on 3D-printing has focused on demonstrating technical potential. This study adds a practitioners’ perspective, with a large dose of pragmatism.

Enclosed print heads have recently been developed as an improvement on the traditional squeegee methods for solder paste printing. They offer the opportunity of widening the printing process window and reducing process waste. Consequently, this work was undertaken to evaluate some aspects of enclosed print head printing, and it has been shown to be a robust process. A number of performance factors were established: with increased humidity the paste degradation was limited due to its sealed paste reservoir; the system also permitted successful intermittent printing over a 5 day period; printing is much more tolerant to distorted substrates than some squeegee blades, and hence improves printing on non‐planar surfaces; significant reduction in paste wastage occurs, since paste ageing is reduced.

To synthesize some new heterocyclic disperse azo dyes and their utilization in textile printing.

To prepare 1‐cayno‐1‐substituted aryl azo‐2‐methyl benzothiazole by the reaction of 2‐aminothiophenol with malononitrile and the end product coupled with different diazonium salts. The prepared dyestuffs are established using element analysis, IR measurements, ¹H‐NMR and Mass spectra. Printing pastes containing the prepared dyestuffs and a thickener were used for printing polyester and/or nylon 6 using either transfer printing or traditional printing.

New selected arylazo cyanomethyl benzothiazole dyes were obtained from the reaction of diazotized aniline derivatives with 2‐cyanomethyl benzothiazole as a coupling component. The suitability of the prepared dyestuffs for either heat transfer printing or traditional printing on polyester and nylon 6 fabrics has been investigated. The prints obtained from dyes containing non polar groups which have sublimation properties possess high colour strength as well as good overall fastness properties if compared to those obtained using dyes containing polar groups.

The new heterocyclic disperse azo dyes were prepared from 2‐cyanomethylbenzothiazole and were utilized in preparing pastes for textile printing to print polyester and nylon 6 fabrics. In addition, the variation in substituents on the synthesized dyes could also be studied.

The method of synthesis of the new dyestuffs provides a simple and practical solution to prepare some new heterocyclic disperse azo dyes with low molecular weight, suitable for sublimation in heat transfer printing methods.

The methods for synthesis of the new heterocyclic disperse azo dyes are simple. These dyestuffs could be used in textile printing of polyester and nylon 6 on an industrial scale.

The purpose of this paper is to describe the development of a 3D printing pilot project and 3D printing library service. Policy development, instruction, and best practices will be shared and explored.

This paper describes the implementation of 3D printing at the University of Regina Library and details successes, failures, and modifications made to better provide 3D printing services. This paper outlines one academic library’s experience and solutions to offering 3D printing for university patrons.

Although 3D printing has been around for a while, it still requires trial and error and experience in order to print successfully. Training and instruction is needed to run the 3D printer and understand how to develop 3D objects that will print successfully.

There have been many publications on 3D printing, but few that discuss problem solving, best practices, and policy development. 3D printing provides a way for patrons to learn about new technology and use that technology to help support learning.

Recent years have seen a rapid development of ink‐jet printing technology. This paper reviews the state‐of‐the‐art in ink‐jet printing technology and gives an overview of ink‐jet printing into the immediate future. The focus is placed on various applications of jet printing technology. The potential of applying jetting technology in the conventionally surface coating dominated applications will also be explored.

The purpose of this study is to identify the print effects produced on selected fabrics due to the adaptation of styrofoam, plastic net and wood as stamp blocks for printing.

The art-based experimental research approach was used to produce and identify the art (prints) produced by stamp blocks on different fabrics using water-soluble print paste.

They stamp block surfaces used in the block printing process produced interesting effects or prints that are uniquely associated with each other. Fabrics such as silver and satin produced shinny print effects coupled with a tough hand or feel as compared to a paperish hand produced on the surfaces of cotton-polyester blend and linen fabrics. The addition of white glue to the paste produced a smooth and embossed-like print effect on fabrics like mercerised cotton and linen. Further results were captured to indicate the hand of these fabrics after printing due to the change in viscosity of the print paste.

The use of calabash and wood surfaces as stamp blocks used in Ghana and the rest of the world is common for printing patterns on fabrics. This study essentially reveals the possibility of using different surfaces for stamp blocks which produce aesthetically pleasing print effects. This when adopted by craftsmen and students would widen the teaching and creative scope in block printing and further produce viable prints for the market using available materials in the environment. These activities would promote and maintain the philosophy of block printing even in the era of advance printing technologies.

The purpose of this paper is to investigate the effect of different viscosity models (Cross and Al-Ma’aiteh) and different printing speeds on the numerical results (e.g. pressure over stencil) of a numerical model regarding stencil printing.

A finite volume model was established for describing the printing process. Two types of viscosity models for non-Newtonian fluid properties were compared. The Cross model was fitted to the measurement results in the initial state of a lead-free solder paste, and the parameters of a Al-Ma’aiteh material model were fitted in the stabilised state of the same paste. Four different printing speeds were also investigated from 20 to 200 mm/s.

Noteworthy differences were found in the pressure between utilising the Cross model and the Al-Ma’aiteh viscosity model. The difference in pressure reached 33-34% for both printing speeds of 20 and 70 mm/s and reached 31% and 27% for the printing speed of 120 and 200 mm/s. The variation in the difference was explained by the increase in the rates of shear by increasing printing speeds.

Parameters of viscosity model should be determined for the stabilised state of the solder paste. Neglecting the thixotropic paste nature in the modelling of printing can cause a calculation error of even approximately 30%. By using the Al-Ma’aiteh viscosity model over the stabilised state of solder pastes can provide more accurate results in the modelling of printing, which is necessary for the effective optimisation of this process, and for eliminating soldering failures in highly integrated electronic devices.

The purpose of this paper is to study a feasible visualization of large-size three-dimension (3D) color models which are beyond the maximum print size of newest paper-based 3D printer used 3D cutting-bonding frame (3D-CBF) and evaluate the effects of cutting angle and layout method on printing time of designed models.

Sixteen models, including cuboid model, cylinder model, hole model and sphere model with different shape features, were divided into two symmetric parts and printed by the Mcor IRIS HD 3D printer. Before printing, two sub-parts were rearranged in one of three layout methods. Nine scaled sizes of original models were printed to find the quantitative relationship between printing time and scale values in each type. For the 0.3 times of original models, six cutting angles were evaluated in detail.

The correlation function about colorization time and printed pages was proposed. Based on 3D-CBF, the correlation between printing time and scale size is statistically defined. Optimization parameters of designed parts visualization about cutting angel and layout method were found, even if their statistical results were difficult to model their effects on printing time of specimens.

The research is comparative and limited to the special models and used procedures.

The paper provides a feasible visualization and printing speed optimization methods for the further industrialization of 3D paper-based printing technology in cultural creative field.

In pursuit of affordable and nutrient-rich food alternatives, the symbiotic culture of bacteria and yeast (SCOBY) emerged as a selected food ink for 3D printing. The purpose of this paper is to harness SCOBY’s potential to create cost-effective and nourishing food options using the innovative technique of 3D printing.

This work presents a comparative analysis of the printability of SCOBY with blends of wheat flour, with a focus on the optimization of process variables such as printing composition, nozzle height, nozzle diameter, printing speed, extrusion motor speed and extrusion rate. Extensive research was carried out to explore the diverse physical, mechanical and rheological properties of food ink.

Among the ratios tested, SCOBY, with SCOBY:wheat flour ratio at 1:0.33 exhibited the highest precision and layer definition when 3D printed at 50 and 60 mm/s printing speeds, 180 rpm motor speed and 0.8 mm nozzle with a 0.005 cm³/s extrusion rate, with minimum alteration in colour.

Food layered manufacturing (FLM) is a novel concept that uses a specialized printer to fabricate edible objects by layering edible materials, such as chocolate, confectionaries and pureed fruits and vegetables. FLM is a disruptive technology that enables the creation of personalized and texture-tailored foods, incorporating desired nutritional values and food quality, using a variety of ingredients and additions. This research highlights the potential of SCOBY as a viable material for 3D food printing applications.

3D printing has been warmly welcomed by clothing enterprises for its customization capacity in recent years. However, such clothing enterprises have to face the digital transformation challenges brought by 3D printing. Since the business model is a competitive weapon for modern enterprises, there is a research gap between business model innovation and digital transformation challenges for 3D-printing garment enterprises. The aim of the paper is to innovate a new business model for 3D-printing garment enterprises in digital transformation.

A business model innovation canvas (BMIC), a new method for business model innovation, is used to innovate a new 3D-printing clothing enterprises business model in the context of digital transformation. The business model canvas (BMC) method is adopted to illustrate the new business model. The business model ecosystem is used to design the operating architecture and mechanism of the new business model.

First, 3D-printing clothing enterprises are facing digital transformation, and they urgently need to innovate new business models. Second, mass customization and distributed manufacturing are important ways of solving the business model problems faced by 3D-printing clothing enterprises in the process of digital transformation. Third, BMIC has proven to be an effective tool for business model innovation.

The new mass deep customization-distributed manufacturing (MDC-DM) business model is universal. As such, it can provide an important theoretical reference for other scholars to study similar problems. The digital transformation background is taken into account in the process of business model innovation. Therefore, this is the first hybrid research that has been focused on 3D printing, garment enterprises, digital transformation and business model innovation. On the other hand, business model innovation is a type of exploratory research, which means that the MDC-DM business model’s application effect cannot be immediately observed and requires further verification in the future.

The new business model MDC-DM is not only applicable to 3D-printing garment enterprises but also to some other enterprises that are either using or will use 3D printing to enhance their core competitiveness.

A new business model, MDC-DM, is created through BMIC, which allows 3D-printing garment enterprises to meet the challenges of digital transformation. In addition, the original canvas of the MDC-DM business model is designed using BMC. Moreover, the ecosystem of the MDC-DM business model is constructed, and its operation mechanisms are comprehensively designed.