Search results
1 – 10 of 791Xinmeng Zhai, Yue Chen and Yuefeng Li
The purpose of this paper is to develop a new composite solder to improve the reliability of composite solder joints. Nano-particles modified multi-walled carbon nanotubes…
Abstract
Purpose
The purpose of this paper is to develop a new composite solder to improve the reliability of composite solder joints. Nano-particles modified multi-walled carbon nanotubes (Ni-MWCNTs) can indeed improve the microstructure of composite solder joints and improve the reliability of solder joints. Although many people have conducted in-depth research on the composite solder of Ni-MWCNTs. However, no one has studied the performance of Ni-MWCNTs composite solder under different aging conditions. In this article, Ni-MWCNTs was added to Sn-Ag-Cu (SAC) solder, and the physical properties of composite solder, the microstructure and mechanical properties were evaluated.
Design/methodology/approach
In this study, the effect of different aging conditions on the intermetallic compound (IMC) layer growth and shear strength of Ni-modified MWCNTs reinforced SAC composite solder was studied. Compared with SAC307 solder alloy, the influence of Ni-MWCNTs with different contents (0, 0.1 and 0.2 Wt.%) on composite solder was examined. To study the aging characteristics of composite solder joints, the solder joints were aged at 80°C, 120°C and 150°C.
Findings
The experimental results show that the content of Ni-MWCNTs affects the morphology and growth of the IMC layer at the interface. The microhardness of the solder increases and the wetting angle decreases. After aging at moderate (120°C) and high temperature (150°C), the morphology of the Cu6Sn5 IMC layer changed from scallop to lamellar and the grain size became coarser. The following two different phase compositions were observed in the solder joints with Ni-MWCNTs reinforcement: Cu3Sn and (Cu, Ni)6Sn5. The fracture surface of the solder joints all appeared ductile dents, and the size of the pits increased significantly with the increase of the aging temperature. Through growth kinetic analysis, Ni-modified MWCNTs in composite solder joints can effectively inhibit the diffusion of atoms in solder joints. In short, when the addition amount of Ni-MWCNTs is 0.1 Wt.%, the solder joints exhibit the best wettability and the highest shear strength.
Originality/value
In this study, the effects of aging conditions on the growth and shear strength of the IMC layer of Ni modified MWCNTs reinforced SAC307 composite solder were studied. The effects of Ni MWCNTs with different contents (0, 0.1 and 0.2 Wt.%) on the composite solder were examined.
Details
Keywords
Feng Tai, Fu Guo, Jianping Liu, Zhidong Xia, Yaowu Shi, Yongping Lei and Xiaoyan Li
The purpose of this paper is to investigate the creep properties of Sn‐0.7Cu composite solder joints reinforced with optimal nano‐sized Ag particles in order to improve the creep…
Abstract
Purpose
The purpose of this paper is to investigate the creep properties of Sn‐0.7Cu composite solder joints reinforced with optimal nano‐sized Ag particles in order to improve the creep performance of lead‐free solder joints by a composite approach.
Design/methodology/approach
The composite approach has been considered as an effective method to improve the creep performance of solder joints. Nano‐sized Ag reinforcing particles were incorporated into Sn‐0.7Cu solder by mechanically mixing. A systematic creep study was carried out on nano‐composite solder joints reinforced with optimal nano‐sized Ag particles and compared with Sn‐0.7Cu solder joints at different temperatures and stress levels. A steady‐state creep constitutive equation for nano‐composite solder joints containing the best volume reinforcement was established in this study. Microstructural features of solder joints were analyzed to help determine their deformation mechanisms during creep.
Findings
The creep activation energies and stress exponents of Ag particle‐enhanced Sn‐0.7Cu lead‐free based composite solder joints were higher than those of matrix solder joints under the same stress and temperature. Thus, the creep properties of nano‐composite solder joints are better than those of Sn‐0.7Cu solder joints.
Originality/value
The findings indicated that nano‐sized Ag reinforcing particles could effectively improve the creep properties of solder joints. A new steady‐state creep constitutive equation of nano‐composite solder joints was established. Deformation mechanisms of Sn‐0.7Cu solder and nano‐composite solder joints during creep were determined.
Details
Keywords
Xinmeng Zhai, Yue Chen, Yuefeng Li, Jun Zou, Mingming Shi and Bobo Yang
This study aims to study the mechanical, photoelectric, and thermal reliability of SAC307 solder joints with Ni-decorated MWCNTs for flip-chip light-emitting diode (LED) package…
Abstract
Purpose
This study aims to study the mechanical, photoelectric, and thermal reliability of SAC307 solder joints with Ni-decorated MWCNTs for flip-chip light-emitting diode (LED) package component during aging. By adding nanoparticles (Ni-multi-walled carbon nanotubes [MWCNTs]) to the solder paste, the shear strength and fatigue resistance of the brazed joint can be improved. However, the aging properties of Ni-modified MWCNTs composite solder joints have not been deeply studied. In this research, the mechanical, photoelectric and thermal reliability of SAC307 packaged flip-chip LEDs with Ni-MWCNTs added during aging were studied.
Design/methodology/approach
Compared with SAC solder alloys, the effects of different contents (0, 0.05, 0.1 and 0.2 Wt.%) of Ni-MWCNTs on the photoelectric and thermal properties of composite solder joints were examined. To study the aging characteristics of composite solder joints, the solder joints were aged at 85°C/85% relative humidity.
Findings
The addition of an appropriate amount of reinforcing agent Ni-MWCNTs reduces the density of the composite solder to 96% of the theoretical value of the SAC solder alloy. In addition, the microhardness increases and the wetting angle decreases. Two different phase compositions were observed in the solder joints with Ni-MWCNTs reinforcement: Cu3Sn and (Cu, Ni)6Sn5. The solder joints of SAC307-0.1Ni-MWCNTs exhibit the highest luminous flux and luminous efficiency of flip-chip LED filaments, the lowest steady-state voltage and junction temperature. And with the extension of the aging time, its aging stability is the best. In short, when the addition amount of Ni-MWCNTs is 0.1 Wt.%, the solder joints exhibit the best wettability and the thinnest intermetallic compound layer. And the shear strength of the tested solder joints is the best, and the void ratio is the lowest. At this time, the enhancement effect of Ni-MWCNTs on the composite solder has been best demonstrated.
Research limitations/implications
The content range of enhancer Ni-MWCNTs needs to be further reduced.
Practical implications
The authors have improved the performance of Ni-modified MWCNTs composite solder joints.
Originality/value
Composite solder with high performance has great practical application significance for improving the reliability and life of the whole device.
Details
Keywords
Guang Chen, Bomin Huang, Hui Liu, Y.C. Chan, Zirong Tang and Fengshun Wu
The purpose of this paper is to investigate microstructure and properties of Sn3.0Ag0.5Cu-XAl2O3 composite solder which were prepared through powder metallurgy route.
Abstract
Purpose
The purpose of this paper is to investigate microstructure and properties of Sn3.0Ag0.5Cu-XAl2O3 composite solder which were prepared through powder metallurgy route.
Design/methodology/approach
Sn3.0Ag0.5Cu (SAC305)-XAl2O3 (X = 0.2, 0.4, 0.6, 0.8 Wt. %) composite solders were prepared through the powder metallurgy route. The morphology of composite solder powders which consists of Al2O3 particles and SAC solder powders after ball milling was observed. The retained ratio of Al2O3 nanoparticles in composite solder billets and solder joints were also quantitatively measured. Furthermore, the as-prepared composite solder alloys were studied extensively with regard to their microstructures, thermal property, wettability and mechanical properties.
Findings
After ball milling, the Al2O3 nanoparticles added were observed embedded into the surface of SAC solder powders. Only about 5-10 per cent of the initial Al2O3 nanoparticles added were detected in the composite solder joints after reflow. In addition, finer ß-Sn grains were achieved with addition of Al2O3 nanoparticles; the Al2O3 nanoparticles were found retained in the composite solder matrix. Besides, negligible changes in melting temperature and the considerably reduced undercooling were obtained in composite solder alloys. Wettability was improved by appropriate addition of Al2O3 nanoparticles. Microhardness and shear strength of composite solders were both improved after Al2O3 nanoparticles addition.
Originality/value
This paper indicated that powder metallurgy route offered a feasible approach to produce nanoparticle reinforced composite solder. In addition, the quantitative analysis of the actual retained ratio of the Al2O3 nanoparticles in solder joints provided practical implications for the manufacture of composite solders.
Details
Keywords
F. Guo, S. Choi, J.P. Lucas and K.N. Subramanian
Composite solders were prepared by mechanically dispersing 15v% of Cu or Ag particles into the eutectic Sn‐3.5Ag solder. The average sizes for the nominally spherical Cu and Ag…
Abstract
Composite solders were prepared by mechanically dispersing 15v% of Cu or Ag particles into the eutectic Sn‐3.5Ag solder. The average sizes for the nominally spherical Cu and Ag particles were 6 and 4 microns, respectively. Two different processing methods were used to prepare the composite solders: blending the powdered particles with solder paste, and adding particles to the molten solder at 2808C. The composite solders were characterised by studying the morphology, size and distribution of the reinforcing phase. Particular interest and emphasis are given towards the modifications of the reinforcements during the reflow process. Microstructural features and chemical analysis of the composite solders were studied using optical and scanning electron microscopy (SEM), and energy dispersive x‐ray (EDX) analysis. The effect of reflow and isothermal ageing on the microstructure as well as the morphological changes in the interfacial IM layer of the composite solders were extensively analysed. A mechanism for IM layer growth is proposed for solid state isothermal ageing.
Details
Keywords
F. Guo, J. Lee and K.N. Subramanian
In an attempt to improve service life of lead‐free Sn‐based electronic solder joints, compatible reinforcements were introduced by in‐situ and mechanical mixing methods. The…
Abstract
In an attempt to improve service life of lead‐free Sn‐based electronic solder joints, compatible reinforcements were introduced by in‐situ and mechanical mixing methods. The reinforcements affect the steady‐state creep rate and the strain for the onset of tertiary creep of the solder joints. However, neither of these parameters, when considered alone, can be used for evaluating the reliability of solder joints. The Larson‐Miller parameter, and a new parameter proposed in the paper, can incorporate test parameters to arrive at a reliability prediction methodology. The role of these reinforcements in homogenising creep strain within the joint is analysed. The observed creep behaviour of these composite solders is discussed on the basis of interfacial bonding strength between the reinforcement and the solder matrix.
Details
Keywords
A series of composite solders in 63/37 Sn/Pb was prepared: Cu6 Sn5 (10, 20,30 wt%); Cu3 Sn (10, 20, 30 wt%); Cu (7.6 wt%); Ag (4 wt%); and Ni (4 wt%). These composite solders were…
Abstract
A series of composite solders in 63/37 Sn/Pb was prepared: Cu6 Sn5 (10, 20, 30 wt%); Cu3 Sn (10, 20, 30 wt%); Cu (7.6 wt%); Ag (4 wt%); and Ni (4 wt%). These composite solders were prepared by two procedures: (A) admixture with solder paste; and (B) admixture with molten solder. The original particulates and the final composite solders were analysed and characterised by SEM (scanning electron microscopy) EDX (energy dispersive X‐ray), and ESCA (electron spectroscopy for chemicals analysis); or XPS (X‐ray photoelectron spectroscopy). A variety of morphological characterisations, intermetallics and porosities were noted. Good wetting was noted in all cases, and porosity was greater for method (A). The particulates all exhibited excellent binding to the solder matrix.
Details
Keywords
O. Nousiainen, T. Kangasvieri, R. Rautioaho and J. Vähäkangas
The purpose of this paper is to present a novel Sn7In4.1Ag0.5Cu/Plastic Core Solder Ball/Sn4Ag0.5Cu composite solder joint configuration for second‐level ball grid array (BGA…
Abstract
Purpose
The purpose of this paper is to present a novel Sn7In4.1Ag0.5Cu/Plastic Core Solder Ball/Sn4Ag0.5Cu composite solder joint configuration for second‐level ball grid array (BGA) interconnections of low temperature co‐fired ceramic (LTCC) modules and the thermal fatigue durability of the configuration. The purpose of using the Sn7In4.1Ag0.5Cu solder was to increase the creep/fatigue resistance of critical regions on the LTCC side of the joint.
Design/methodology/approach
Test LTCC module/printed wiring board (PWB) assemblies were fabricated and exposed into temperature cycling tests over the 0 to 100°C and −40 to 125°C temperature ranges. The characteristic lifetimes of these assemblies were determined using DC resistance measurements. The failure mechanisms of the test assemblies were verified using scanning acoustic microscopy, FE‐SEM, and SEM investigation.
Findings
The test assemblies were exposed to thermal cycling tests (TCT) over test ranges of 0 to 100°C and −40 to 125°C, and characteristic lifetimes of over 5,500 and 1,400 cycles, respectively, were achieved. Compared with Sn4Ag0.5Cu/plastic‐core solder balls (PCSB)/Sn4Ag0.5Cu joints, the characteristic lifetime of the SAC‐In/PCSB/SAC joints increased over 55 per cent in the harsh (−40 to 125°C) TCT conditions. In the milder test conditions (0 to 100°C), the characteristic lifetime of the SAC‐In/PCSB/SAC joints increased 30 per cent compared with the SAC/PCSB/SAC joints.
Originality/value
The results proved that the enhanced creep/fatigue properties of the solder matrix resulted in satisfactory lifetime durations in the present lead‐free composite solder joints and, consequently, different primary failure mechanisms on the LTCC side due to the use of indium alloyed solder. Thus, the present joint configuration is assumed to be a promising solution for the further design of a reliable second‐level solder interconnection in LTCC/PWB assemblies with a high‐global thermal mismatch.
Details
Keywords
Guang Chen, Li Liu, Vadim V. Silberschmidt, Y.C. Chan, Changqing Liu and Fengshun Wu
This paper aims to systematically study the effect of reinforcement type, processing methods and reflow cycle on actual retained ratio of foreign reinforcement added in solder…
Abstract
Purpose
This paper aims to systematically study the effect of reinforcement type, processing methods and reflow cycle on actual retained ratio of foreign reinforcement added in solder joints.
Design/methodology/approach
Two kinds of composite solders based on SAC305 (wt.%) alloys with reinforcements of 1 wt.% Ni and 1 wt.% TiC nano-particles were produced using powder metallurgy and mechanical blending method. The morphology of prepared composite solder powder and solder pastes was examined; retained ratios of reinforcement (RRoR) added in solder joints after different reflow cycles were analysed quantitatively using an Inductively Coupled Plasma optical system (ICP-OES Varian-720). The existence forms of reinforcement added in solder alloys during different processing stages were studied using scanning electron microscope, X-ray diffractometry and energy dispersive spectrometry.
Findings
The obtained experimental results indicated that the RRoR in composite solder joints decreased with the increase in the number of reflow cycles, but a loss ratio diminished gradually. It was also found that the RRoR which could react with the solder alloy were higher than that of the one that are unable to react with the solder. In addition, compared with mechanical blending, the RRoRs in the composite solders prepared using power metallurgy were relatively pronounced.
Originality/value
Present study offer a preliminary understanding on actual content and existence form of reinforcement added in a reflowed solder joint, which would also provide practical implications for choosing reinforcement and adjusting processing parameters in the manufacture of composite solders.
Details
Keywords
Hao Zhang, Yang Liu, Fenglian Sun, Gaofang Ban and Jiajie Fan
This paper aimed to investigate the effects of nano-copper particles on the melting behaviors, wettability and defect formation mechanism of the Sn58Bi composite solder pastes.
Abstract
Purpose
This paper aimed to investigate the effects of nano-copper particles on the melting behaviors, wettability and defect formation mechanism of the Sn58Bi composite solder pastes.
Design/methodology/approach
In this paper, the mechanical stirring method was used to get the nano-composite solder pastes.
Findings
Experimental results indicated that the addition of 3 wt.% (weight percentage) 50 nm copper particles showed limited effects on the melting behaviors of the Sn58Bi composite solder paste. The spreading rate of the Sn58Bi composite solder paste showed a decreasing trend with the increase of the weight percentage of 50 nm copper particles from 0 to 3 wt.%. With the addition of copper particles of diameters 50 nm, 500 nm or 6.5 μm into the Sn58Bi solder paste, the porosities of the three types of solder pastes showed a similar trend. The porosity increased with the increase of the weight percentage of copper particles. Based on the experimental results, a model of the void formation mechanism was proposed. During reflow, the copper particles reacted with Sn in the matrix and formed intermetallic compounds, which gathered around the voids produced by the volatilization of flux. The exclusion of the voids was suppressed and eventually led to the formation of defects.
Originality/value
This study provides an optimized material for the second and third level packaging. A model of the void formation mechanism was proposed.
Details