Search results

The purpose of this paper is to study a new liquid-phase assisted texture treatment method to improve the tribological properties of 304 stainless steel.

Three groups of textured type (KY, KJ and YJ) were prepared on 304 stainless steel surface using laser circular and cross scanning method in air and liquid assisted condition. The surface morphology and element content of test samples were measured with scanning electron microscope, energy spectrum. Then, the tribological test was carried out using MWF-500 reciprocating friction and wear testing machine under dry and oil lubrication condition.

The experimental results showed that the textured surface of laser processing in air was obviously blackened, and the oxygen content was increased from 16.9% to 24%. These cases did not occur on liquid-assisted laser textured surface, which induced a better wettability and surface texture processing quality. For friction test, the friction coefficient of cross-scanning textured surface prepared in assisted liquid (YJ) was the smallest. It is reduced by 55% in oil lubrication case compared to the original surface (YS). The cross-scanning textured surface prepared in air (KJ) was a little worse in friction coefficient and a little better in wear quantity than the cross-scanning textured surface prepared in assisted liquid (YJ). It is indicated that the laser processing surface with assisted liquid has obvious advantages in surface texture quality and interfacial tribological property. The main reason is that the assisted liquid plays a role in cooling and protecting action of the machined surface. The bubbles, generated at the solid–liquid interface because of the laser heat effect, scatter the laser beam and carry out the processed melt meanwhile. The lubricating medium is easier to penetrate and store in the contact interfaces because of the higher surface textured performance and wettability.

The main contribution of this work is in providing a new surface texture processing method that has a better surface micropits quality and interfacial tribology regulation ability.

The purpose of this study is to optimize and improve conventional welding using EMF assisted technology. Current industrial production has put forward higher requirements for welding technology, so the optimization and improvement of traditional welding methods become urgent needs.

External magnetic field assisted welding is an emerging technology in recent years, acting in a non-contact manner on the welding. The action of electromagnetic forces on the arc plasma leads to significant changes in the arc behavior, which affects the droplet transfer and molten pool formation and ultimately improve the weld seam formation and joint quality.

In this paper, different types of external magnetic fields are analyzed and summarized, which mainly include external transverse magnetic field, external longitudinal magnetic field and external cusp magnetic field. The research progress of welding behavior under the effect of external magnetic field is described, including the effect of external magnetic field on arc morphology, droplet transfer and weld seam formation law.

However, due to the extremely complex physical processes under the action of the external magnetic field, the mechanism of physical fields such as heat, force and electromagnetism in the welding has not been thoroughly analyzed, in-depth theoretical and numerical studies become urgent.

This paper aims to propose a suitable atomizing solidification chitosan (CS) gel liquid extrusion molding technology for the three dimensional (3D) printing method, and experiments verify the feasibility of this method.

This paper mainly uses experimental means, combined with theoretical research. The preparation method, solidification forming method and 3D printing method of CS gel solution were studied. The CS gel printing mechanism and printing error sources are analyzed on the basis of the CS gel ink printing results, printing performance with different ratios of components by constructing a gel print prototype, experiments evaluating the CS gel printing technology and the effects of the process parameters on the scaffold formation.

CS printing ink was prepared; the optimal formula was found; the 3 D printing experiment of CS was completed; the optimal printing parameters were obtained; and the reliability of the forming prototype, printing ink and gel printing process was verified, which allowed for the possibility to apply the 3 D printing technology to the manufacturing of a CS gel structure.

This study can provide theoretical and technical support for the potential application of CS 3 D printed gels in tissue engineering.

This study aims to investigate the interfacial microstructures of ultrasonic-assisted solder joints at different soldering times.

Solder joints with different microstructures are obtained by ultrasonic-assisted soldering. To analyze the effect of ultrasounds on Cu₆Sn₅ growth during the solid–liquid reaction stage, the interconnection heights of solder joints are increased from 30 to 50 μm.

Scallop-like Cu₆Sn₅ nucleate and grow along the Cu₆Sn₅/Cu₃Sn interface under the traditional soldering process. By comparison, some Cu₆Sn₅ are formed at Cu₆Sn₅/Cu₃Sn interface and some Cu₆Sn₅ are randomly distributed in Sn when ultrasonic-assisted soldering process is used. The reason for the formation of non-interfacial Cu₆Sn₅ has to do with the shock waves and micro-jets produced by ultrasonic treatment, which leads to separation of some Cu₆Sn₅ from the interfacial Cu₆Sn₅ to form non-interfacial Cu₆Sn₅. The local high pressure generated by the ultrasounds promotes the heterogeneous nucleation and growth of Cu₆Sn₅. Also, some branch-like Cu₃Sn formed at Cu₆Sn₅/Cu₃Sn interface render the interfacial Cu₃Sn in ultrasonic-assisted solder joints present a different morphology from the wave-like or planar-like Cu₃Sn in conventional soldering joints. Meanwhile, some non-interfacial Cu₃Sn are present in non-interfacial Cu₆Sn₅ due to reaction of Cu atoms in liquid Sn with non-interfacial Cu₆Sn₅ to form non-interfacial Cu₃Sn. Overall, full Cu₃Sn solder joints are obtained at ultrasonic times of 60 s.

The obtained microstructure evolutions of ultrasonic-assisted solder joints in this paper are different from those reported in previous studies. Based on these differences, the effects of ultrasounds on the formation of non-interfacial IMCs and growth of interfacial IMCs are systematically analyzed by comparing with the traditional soldering process.

The amount of food wasted every year is 1.3 billion metric tonne (MT), out of which 0.5 billion MT is contributed by the fruits processing industries. The waste includes by-products such as peels, pomace and seeds and is a good source of bioactive compounds like phenolic compounds, flavonoids, pectin lipids and dietary fibres. Hence, the purpose of the present study is to review the novel extraction techniques used for the extraction of the bio active compounds from food waste for the selection of suitable extraction method.

Novel extraction techniques such as ultrasound-assisted extraction, microwave-assisted extraction, enzyme-assisted extraction, supercritical fluid extraction, pulsed electric field extraction and pressurized liquid extraction have emerged to overcome the drawbacks and constraints of conventional extraction techniques. Hence, this study is focussed on novel extraction techniques, their limitations and optimization for the extraction of bioactive compounds from fruit and vegetable waste.

This study presents a comprehensive review on the novel extraction processes that have been adopted for the extraction of bioactive compounds from food waste. This paper also summarizes bioactive compounds' optimum extraction condition from various food waste using novel extraction techniques.

Food waste is rich in bioactive compounds, and its efficient extraction may add value to the food processing industries. Hence, compressive analysis is needed to overcome the problem associated with the extraction and selection of suitable extraction techniques.

Selection of a suitable extraction method will not only add value to food waste but also reduce waste dumping and the cost of bioactive compounds.

This paper presents the research progress on the extraction of bioactive active compounds from food waste using novel extraction techniques.

In this study, the purpose has been to investigate a novel pathway for the synthesis of high performance diketopyrrolopyrrole pigments (DPPs) using diethyl succinate under microwave irradiation in the presence of ionic liquid (1‐butyl‐3‐methylimidazolium tetrafluoroborate, [BMIM][BF₄]), as a novel medium.

Rapid synthesis of DPPs was achieved in [BMIM][BF₄] as well as in dry medium under microwave irradiation based on succinate ester condensation with benzonitrile derivatives. The obtained results were compared with those of conventional method as well as Reformatsky route under microwave irradiation. The obtained pigments were characterized and their optical properties and the morphologies were investigated.

This study provides a novel approach to the synthesis of DPP pigments in a flash time with comparatively good yields.

DPPs have been synthesized via succinate ester route in ionic liquid media. Besides, they can also be synthesized based on Reformatsky method in ionic liquid media.

The developed method provides a simple and practical solution to improving the rapid synthesis of DPP pigments, with regard to their traditional application in many different industries, such as paints, inks, and plastics, as well as in electronic devices, LEDs, and laser dyes.

The method for synthesis of DPP pigments via succinate ester route in ionic liquid under microwave irradiation in a flash time was novel and could find applications in DPP pigments' industries.

Liquid-assisted laser surface texturing technology was used to create composite microtextures on triangular guide rail surfaces to enhance their tribological properties.

Numerical simulations were used to investigate the impact of various microtextures on fluid dynamic lubrication. Reciprocating friction and wear tests, followed by mechanistic analysis, examined the combined tribological effects of microtextured surfaces and lubricants.

The numerical simulation outcomes reveal a significant augmentation in the influence of fluid dynamic pressure due to composite microtextures, consequently amplifying the load-bearing capacity of the oil film. The average friction coefficient of composite microtextured samples was approximately 0.136 in reciprocating pin-on-disk friction tests, representing approximately 17% decrease compared to polished samples. Triangular guide rails with composite microtextures demonstrated the lowest average coefficient under conditions of high-speed and heavy-loading in the reciprocating friction and wear tests. Additionally, the presence of composite microtextures was found to promote the formation of adsorbed and friction films during friction, potentially contributing to the enhancement of tribological properties.

Triangular guide rails face high friction and wear, limiting their stability in demanding applications like machine tool guideways. This paper proposes a novel approach for steel triangular guide rails, involving composite microtexturing, numerical fluid simulations, liquid-assisted laser surface texturing and friction-wear testing. By implementing composite microtextures, the method aims to reduce friction coefficients and extend guideway service life, thereby saving energy and reducing maintenance costs. Enhancing the antifriction and antiwear properties of machine tool guideways is crucial for improving performance and longevity.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2024-0183/

This paper aims to understand the magnetohydrodynamics (MHD) mechanism in the molten pool under different modes of magnetic field. The comparison focuses on the Lorenz force excitation and its effect on the melt flow and solidification parameters, intending to obtain practical references for the design of magnetic field-assisted laser directed energy deposition (L-DED) equipment.

A three-dimensional transient multi-physical model, coupled with MHD and thermodynamic, was established. The dimension and microstructure of the molten pool under a 0T magnetic field was used as a benchmark for accuracy verification. The interaction between the melt flow and the Lorenz force is compared under a static magnetic field in the X-, Y- and Z-directions, and also an oscillating and alternating magnetic field.

The numerical results indicate that the chaotic fluctuation of melt flow trends to stable under the magnetostatic field, while a periodically oscillating melt flow could be obtained by applying a nonstatic magnetic field. The Y and Z directional applied magnetostatic field shows the effective damping effect, while the two nonstatic magnetic fields discussed in this paper have almost the same effect on melt flow. Since the heat transfer inside the molten pool is dominated by convection, the application of a magnetic field has a limited effect on the temperature gradient and solidification rate at the solidification interface due to the convection mode of melt flow is still Marangoni convection.

This work provided a deeper understanding of the interaction mechanism between the magnetic field and melt flow inside the molten pool, and provided practical references for magnetic field-assisted L-DED equipment design.

The purpose of this study is to demonstrate the potential of three-dimensional printing technology for the remanufacturing of end-of-life (EoL) composites. This technology will enable the rapid fabrication of environmentally sustainable structures with complex shapes and good mechanical properties. These three-dimensional printed objects will have several application fields, such as street furniture and urban renewal, thus promoting a circular economy model.

For this purpose, a low-cost liquid deposition modeling technology was used to extrude photo-curable and thermally curable composite inks, composed of an acrylate-based resin loaded with different amounts of mechanically recycled glass fiber reinforced composites (GFRCs). Rheological properties of the extruded inks and their printability window and the conversion of cured composites after an ultraviolet light (UV) assisted extrusion were investigated. In addition, tensile properties of composites remanufactured by this UV-assisted technology were studied.

A printability window was found for the three-dimensional printable GFRCs inks. The formulation of the composite printable inks was optimized to obtain high quality printed objects with a high content of recycled GFRCs. Tensile tests also showed promising mechanical properties for printed GFRCs obtained with this approach.

The novelty of this paper consists in the remanufacturing of GFRCs by the three-dimensional printing technology to promote the implementation of a circular economy. This study shows the feasibility of this approach, using mechanically recycled EoL GFRCs, composed of a thermoset polymer matrix, which cannot be melted as in case of thermoplastic-based composites. Objects with complex shapes were three-dimensional printed and presented here as a proof-of-concept.

The holistic numerical model based on cellular automata (CA) and lattice Boltzmann method (LBM) are being developed as part of an integrated modelling approach applied to study the interaction of different physical mechanisms in laser-assisted additive layer manufacturing (ALM) of orthopaedic implants. Several physical events occurring in sequence or simultaneously are considered in the holistic model. They include a powder bed deposition, laser energy absorption and heating of the powder bed by the moving laser beam, leading to powder melting or sintering, fluid flow in the melted pool and flow through partly or not melted material, and solidification. The purpose of this study is to develop a structure of the holistic numerical model based on CA and LBM applicable for studying the interaction of the different physical mechanisms in ALM of orthopaedic implants. The model supposed to be compatible with the earlier developed CA-based model for the generation of the powder bed.

The mentioned physical events are accompanied by heat transfer in solid and liquid phases including interface heat transfer at the boundaries. The sintering/melting model is being developed using LBM as an independent numerical method for hydrodynamic simulations originated from lattice gas cellular automata. It is going to be coupled with the CA-based model of powder bed generation.

The entire laser-assisted ALM process has been analysed and divided on several stages considering the relevant physical phenomena. The entire holistic model consisting of four interrelated submodels has currently been developed to a different extent. The submodels include the CA-based model of powder bed generation, the LBM-CA-based model of heat exchange and transfer, the thermal solid-liquid interface model and the mechanical solid-liquid interface model for continuous liquid flow.

The results obtained can be used to explain the interaction of the different physical mechanisms in ALM, which is an intensively developing field of advanced manufacturing of metal, non-metal and composite structural parts, for instance, in bio-engineering. The proposed holistic model is considered to be a part of the integrated modelling approach being developed as a numerical tool for investigation of the co-operative relationships between multiphysical phenomena occurring in sequence or simultaneously during heating of the powder bed by the moving high energy heat source, leading to selective powder sintering or melting, fluid flow in the melted pool and through partly (or not) melted material, as well as solidification. The model is compatible with the earlier developed CA-based model for the generation of the powder bed, allowing for decrease in the numerical noise.

The present results are original and new for the study of the complex relationships between multiphysical phenomena occurring during ALM process based on selective laser sintering or melting, including fluid flow and heat transfer, identified as crucial for obtaining the desirable properties.