Search results
1 – 10 of 959Hongda Deng, Yongliang Liu, Zhen He, Xiantao Gou, Yefan Sheng, Long Chen and Jianbing Ren
The purpose of this paper is to investigate and explain thermal oxide effect on electrochemical corrosion resistance anodized stainless steel (SS).
Abstract
Purpose
The purpose of this paper is to investigate and explain thermal oxide effect on electrochemical corrosion resistance anodized stainless steel (SS).
Design/methodology/approach
Electrochemical corrosion resistance of thermal oxides produced on anodized 304 SS in air at 350°C, 550°C, 750°C and 950°C in 3.5 wt.% NaCl solution have been investigated by dynamic potential polarization, EIS and double-loop dynamic polarization. Anodized 304 SS were obtained by anodization at the constant density of 1.4 mA.cm-2 in the solution containing 28.0 g.L-1H3PO4, 20.0 g.L-1C6H8O7, 200.0 g.L-1H2O2 at 70°C for 50 min. SEM and EDS had been also used to characterize the thermal oxides and passive oxide.
Findings
Interestingly, anodized 304SS with thermal oxide produced at 350°C displayed more electrochemical corrosion and pitting resistance than anodized 304 SS only with passive oxide, as related to the formation of oxide film with higher chromium to iron ratio. Whereas, anodized 304SS with thermal oxide formed at 950°C shows the worse electrochemical corrosion and pitting resistance among those formed at the high temperatures due to thermal oxide with least compact.
Originality/value
When thermally oxidized in the range of 350°C–950°C, electrochemical corrosion and pitting corrosion resistance of anodized 304 SS decrease with the increase of temperature due to less compactness, more defects of thermal oxide.
Details
Keywords
Ghadanfer Hussein Ali and Sabah Khammass Hussein
The purpose of this paper is to join an anodized aluminium alloy AA6061 sheet with high-density polyethylene (HDPE) using friction spot process.
Abstract
Purpose
The purpose of this paper is to join an anodized aluminium alloy AA6061 sheet with high-density polyethylene (HDPE) using friction spot process.
Design/methodology/approach
The surface of AA6061 sheet was anodized to increase the pores’ size. A lap joint configuration was used to join the AA6061 with HDPE sheets by the friction spot process. The joining process was carried out using a rotating tool of different diameters: 14, 16 and 18 mm. Three tool-plunging depths were used – 0.1, 0.2 and 0.3 mm – with three values of the processing time – 20, 30 and 40 s. The joining process parameters were designed according to the Taguchi approach. Two sets of samples were joined: the as-received AA6061/HDPE and the anodized AA6061/HDPE.
Findings
Frictional heat melted the HDPE layers near the lap joint line and penetrated it through the surface pores of the AA6061 sheet via the applied pressure of the tool. The tool diameter exhibited higher effect on the joint strength than processing time and the tool-plunging depth. Specimens of highest and lowest tensile force were failed by necking the polymer side and shearing the polymer layers at the lap joint, respectively. Molten HDPE was mechanically interlocked into the pores of the anodized surface of AA6061 with an interface line of 18-m width.
Originality/value
For the first time, HDPE was joined with the anodized AA6061 by the friction spot process. The joint strength reached an ideal efficiency of 100 per cent.
Details
Keywords
Increasing utilisation of the properties of hardness, corrosion resistance and electrical insulation has taken place rapidly in recent years. Still scope exists for further…
Abstract
Increasing utilisation of the properties of hardness, corrosion resistance and electrical insulation has taken place rapidly in recent years. Still scope exists for further development of anodised aluminium as knowledge of the mechanism involved grows. In the first of this two‐part article the author deals mainly with bright and conventional architectural anodising.
Self‐coloured films of good light fastness are becoming important architecturally, particularly when colour is combined with a thick film and high abrasion resistance. This aspect…
Abstract
Self‐coloured films of good light fastness are becoming important architecturally, particularly when colour is combined with a thick film and high abrasion resistance. This aspect of anodising is covered in this concluding part of the article. Also covered are conventional hard anodising, anodising in electrical engineering, continuous anodising and quality control. British Standard 1615, also discussed, has recently been brought up to date and is particularly valuable because of the wide range of possible finishes.
Seyed Mohammad Hossein Mousavian and Seyed Hadi Tabaian
The purpose of this study was to investigate the effect of electrolyte compounds on the anodizing process. Magnesium and its alloys have low corrosion resistance. Anodizing…
Abstract
Purpose
The purpose of this study was to investigate the effect of electrolyte compounds on the anodizing process. Magnesium and its alloys have low corrosion resistance. Anodizing operation is performed to increase the corrosion resistance of magnesium. Anodizing solution compounds have a great effect on the oxide coating formed on the substrate. The effect of anodizing electrolyte composition on the corrosion behavior of magnesium was investigated in the simulated body fluid.
Design/methodology/approach
Three pure magnesium samples were anodized separately at 15 min, a constant voltage of 9 volts and room temperature. Three different solutions were used, which are the anodizing solution by the Harry A. Evangelides (HAE) method, the sodium hydroxide solution and the anodizing solution of the HAE method without potassium permanganate. Field emission scanning electron microscope (FE-SEM) was used to examine the surface of the anodized oxide layer and electrochemical impedance spectroscopy (EIS) was used for electrochemical corrosion evaluations.
Findings
The results of corrosion tests showed that the sample anodized in the solution without potassium permanganate has had the highest corrosion resistance. Also, microscopic images showed that the surface of the oxide layer of this sample had a uniform structure and is somewhat smooth. It seems that in the anodizing process by HAE method at 9 volts and for 15 min, the absence of potassium permanganate improves the corrosion resistance of magnesium. Also, anodizing in HAE solution gives more positive results than anodizing in sodium hydroxide solution.
Originality/value
The solution without potassium permanganate was studied for the first time and also the effect of these three anodizing electrolytes was compared together for the first time. Effect of anodizing at 15 min and constant voltage of 9 volts. Sample’s electrochemical behavior in the body's simulation environment has been investigated. Improvement of electrochemical properties in the solution of the HAE method without potassium permanganate.
Details
Keywords
G.E. Thompson, H. Habazaki, K. Shimizu, M. Sakairi, P. Skeldon, X. Zhou and G.C. Wood
Anodizing is used widely in the surface treatment of aluminium alloys for aerospace applications. Considers recent advances in understanding of the influences of alloying elements…
Abstract
Anodizing is used widely in the surface treatment of aluminium alloys for aerospace applications. Considers recent advances in understanding of the influences of alloying elements in anodizing of aluminium alloys and, in particular, their applicability to second phase particles during anodizing of commercial alloys. Through more precise knowledge of the response of second phase materials to anodic polarization, improved anodizing and related surface treatment processes may be developed in order to enhance the performance of aluminium alloys.
Details
Keywords
John M. Perfect, W.J. Campbell, J.W. Cuthbertson, J.C. Bailey, A.W. Brace, J.M. Kape, C.E. Michelson, H. Ginsberg, W. Kaden, J.G. Simmons, B.A. Scott, H.M. Bigford, H. Richaud, Capt. J. Fox‐Williams and H.L. Watts
The Conference on Anodised Aluminium, organised by the Aluminium Development Association and held in the new Cripps Hall at Nottingham University from September 12–14, was…
Abstract
The Conference on Anodised Aluminium, organised by the Aluminium Development Association and held in the new Cripps Hall at Nottingham University from September 12–14, was probably the first of its kind in the world and attracted nearly 300 delegates. Eighteen papers were discussed. In the following pages abstracts and conclusions from most of the papers are given, emphasis being placed on the corrosion aspects of the subject.
With the advent of micro‐satellites technology, passive thermal controls in the form of surface coatings have become important for onboard thermal management. The thermal…
Abstract
Purpose
With the advent of micro‐satellites technology, passive thermal controls in the form of surface coatings have become important for onboard thermal management. The thermal coatings, however, suffer outgassing and mass loss due to their direct exposure to harsh thermal environment and high vacuum in space. The purpose of this paper is to discuss testing and evaluation on outgassing of AA6061‐T6 specimen surfaces treated with various types of anodized coatings of different thicknesses and the related mass loss before and after thermal exposure.
Design/methodology/approach
Samples of chromic acid, polytetrafluroethylene polymer, and black‐ and brown‐colour anodized aluminum coupons were subjected to high vacuum (∼1×10−6 mbar), before and after thermal baking at 120°C. Spectrum analysis of the outgassed material to know their quantities and proportion was conducted subsequently using a Quadrupole mass analyzer.
Findings
The surface coatings under study complied with the spacecraft requirements for the mass loss of less than 1 percent of the total mass of the coating material used for that surface. The mass spectrum analysis of the outgassed material indicated that the majority of the coating mass loss was on account of water vapours and organic solvents like ethylene.
Practical implications
These results provided a good insight into the reliability of the coating materials studied and the bonding between the aluminum substrates and the coatings.
Originality/value
The coatings and the technology needed for their application on aluminum are readily available. The present work on outgassing and mass loss in a simulated space environment will provide useful insight on their usage for micro‐satellites.
Details
Keywords
– The purpose of this work was to study the cracking susceptibility of a 7017 aluminium alloy, after anodising under various conditions.
Abstract
Purpose
The purpose of this work was to study the cracking susceptibility of a 7017 aluminium alloy, after anodising under various conditions.
Design/methodology/approach
Slow strain tests in dry air, laboratory air and sodium chloride solution were employed. Anodic oxide films were produced with various applied current densities and thicknesses, in horizontal or vertical orientation of the coatings, at the free corrosion potential and also at various anodic or cathodic potentials. For the interpretation of the results, a metallographic study of the specimens before and after straining to failure was carried out using a scanning electron microscope.
Findings
The behaviour of anodic coatings was found to depend very much on the anodising conditions. The coatings reduced the ductility of the alloy in dry air but can actually increase the ductility in laboratory air and in 3.5 per cent sodium chloride solution. In most cases, the ductility of coated specimens was greater in 3.5 per cent NaCl solution than in dry air, possibly due to crack blunting by the aggressive environment. Anodic coatings moved the free corrosion potential of the alloy in the noble direction and both the anodised and the bare alloy generally suffered a reduction in ductility at potentials anodic or cathodic to the free corrosion potential, the fall being more rapid for the anodised alloy.
Research limitations/implications
The mechanism causing the increased ductility of coated specimens in 3.5 per cent NaCl solution than in dry air remains yet to be confirmed.
Practical implications
The selection of suitable anodic coatings for the protection of aluminium alloys against stress corrosion cracking depends on the anodising conditions.
Originality/value
The paper provides information regarding the influence of anodising conditions on the anticorrosive properties of electrolytically prepared anodic coatings on aluminium alloys.
Details
Keywords
P.K. Spathis and E. Papastergiadis
The purpose of this paper is to study of the effect of carboxylic acids additions to the anodising bath on the subsequent corrosion and stress corrosion cracking (SCC) tendencies…
Abstract
Purpose
The purpose of this paper is to study of the effect of carboxylic acids additions to the anodising bath on the subsequent corrosion and stress corrosion cracking (SCC) tendencies of anodised 1050 Al‐Alloy in 3M NaCl solution.
Design/methodology/approach
The study was carried out using SCC tests and electrochemical cyclic potentiodynamic measurements at a high or a slow scan rates. The anodic coatings were prepared electrolytically in a bath of 4 M H2SO4, with and without additions of 0.015 M oxalic, malonic, tartaric, maleic, or citric acids. The consequent thicknesses and packing densities of the coatings were measured.
Findings
The SCC behaviour was found to vary with both anodising conditions and stress level. The addition of carboxylic acids in the anodising bath increased the protective properties of the coating. In corrosion conditions without stress, the addition of the carboxylic acids decreased the susceptibility to pitting corrosion, the effect depending on the presence or absence of corrosion products. The addition of the carboxylic acids during anodising leads to the formation of less porous and more compact oxide layers and increases the anticorrosive properties of the coatings. The benefits were most pronounced for the coating prepared in the presence of maleic acid.
Research limitations/implications
The belief that the effect of carboxylic acids on the corrosion and SCC behaviour of Al‐Alloys is due to the absorption of these compounds on the metal surface and the formation of complexes on it, depending on the structure and carbonic chain of these compounds, remains yet to be confirmed.
Practical implications
Anodic coatings prepared in an electrolytic bath containing carboxylic acids can be used for the protection of aluminium alloys against corrosion.
Originality/value
The paper provides information regarding the improvement of the anticorrosive properties of electrolytically prepared anodic coatings on aluminium alloys.
Details