Search results

The development of a new class of engineering materials is the current demand for aircraft and automobile companies. In this context metal, composite materials have a widespread application in different areas of manufacturing sectors.

In this paper, an attempt is made to develop the aluminium-based nano metal matrix composite reinforced with graphene nanoparticles (GNP) by using the stir casting method. Different weight percentage (0.4%, 0.8% and 1.2% by weight) of GNPs are used to fabricate metal matrix composites (MMCs). The developed nanocomposites were further validated by density calculation and optical microstructures to discuss the distribution of GNPs. The tensile test was conducted to determine the strength of the developed MMCs and also supported by fractographic analysis. In addition to it, the Rockwell hardness test and impact test (toughness) with fracture analysis were also conducted to strengthen the present work.

The results reveal the uniform distribution of GNPs into the matrix material. The yield strength and ultimate tensile strength obtained a maximum value of 155.67 MPa and 170.28 MPa, respectively. The hardness value (HRB) is significantly increased and 84 HRB was obtained for the sample with AA1100/0.4% GNP, while maximum hardness value (94 HRB) was obtained for the sample AA1100/1.2% GNP. The maximum value of toughness 14.3 Jules/cm² is recorded for base alloy AA1100 while increasing the reinforcement percentage, it decreases up to 9.7 Jules/cm² for AA1100/1.2% GNP.

Graphene nanoparticles are used to develop nanocomposites, which is one of the suitable alternatives for heavy engineering materials such as steels and cast irons. It has improved microstructural and mechanical properties which makes it preferable for many engineering and structural applications.

The weld joint mechanical properties of friction stir welding (FSW) are majorly reliant on different input parameters of the FSW machine. The study and optmization of these parameters is uttermost requirement and aim of this study to increase the suitability of FSW in different manufacturing industries. Hence, the input parameters are optimized through different soft computing methods to increase the considered objective in this study.

In this research, ultimate tensile strength (UTS), yield strength (YS) and elongation (EL) of FSW prepared butt joints of AA6061 and AA5083 Aluminium alloys materials are investigated as per American Society for Testing and Materials (ASTM E8-M04) standard. The FSW joints were prepared by changing the three input process parameters. To develop experimental run order design matrix, rotatable central composite design strategy was used. Furthermore, genetic algorithm (GA) in combination (Hybrid) with response surface methodology (RSM), artificial neural network (ANN), i.e. RSM-GA, ANN-GA, is exercised to optimize the considered process parameters.

The maximum value of UTS, YS and EL of test specimens on universal testing machine was measured as 264 MPa, 204 MPa and 14.41%, respectively. The most optimized results (UTS = 269.544 MPa, YS = 211.121 MPa and EL = 17.127%) are obtained with ANN-GA for the considered objectives.

The optimization of input parameters to increase the output objective values using hybrid soft computing techniques is unique in this research paper. The outcomes of this study will help the FSW using manufacturing industries to choose the best optimized parameters set for FSW prepared butt joint with improved mechanical properties.

The purpose of this study is to present a comprehensive review of the fundamental concepts and terminologies pertaining to different types of aluminium metal matrix composites, their joining techniques and challenges, friction stir welding (FSW) process, post-welding characterizations and basic control theory of FSW, followed by the discussions on the research reports in these areas.

Joining of aluminium metal matrix composites (Al-MMC) poses many challenges. These materials have their demanding applications in versatile domains, and hence it is essential to understand their weldability and material characteristics. FSW is a feasible choice for joining of Al-MMC over the fusion welding because of the formation of narrow heat affected zone and minimizing the formation of intermetallic compounds at weld interface. The goal in FSW is to generate enough thermal energy by friction between the workpiece and rotating tool. Heat energy is generated by mechanical interaction because of the difference in velocity between the workpiece and rotating tool. In the present work, a detailed survey is done on the above topics and an organised conceptual context is presented. A complete discussion on significance of FSW process parameters, control schemes, parameter optimization and weld quality monitoring are presented, along with the analysis on relation between the interdependent parameters.

Results from the study present the research gaps in the FSW studies for joining of the aluminium-based metal matrix composites, and they highlight further scope of studies pertaining to this domain.

It is observed that the survey done on FSW of Al-MMCs and their control theory give an insight into the fundamental concepts pertaining to this research area to enhance interdisciplinary technology exploration.

This paper aims to present the fabrication of 6061 aluminum alloy (AA6061) using a promising laser additive manufacturing process, called the laser-foil-printing (LFP) process. The process window of AA6061 in LFP was established to optimize process parameters for the fabrication of high strength, dense and crack-free parts even though AA6061 is challenging for laser additive manufacturing processes due to hot-cracking issues.

The multilayers AA6061 parts were fabricated by LFP to characterize for cracks and porosity. Mechanical properties of the LFP-fabricated AA6061 parts were tested using Vicker’s microhardness and tensile testes. The electron backscattered diffraction (EBSD) technique was used to reveal the grain structure and preferred orientation of AA6061 parts.

The crack-free AA6061 parts with a high relative density of 99.8% were successfully fabricated using the optimal process parameters in LFP. The LFP-fabricated parts exhibited exceptional tensile strength and comparable ductility compared to AA6061 samples fabricated by conventional laser powder bed fusion (LPBF) processes. The EBSD result shows the formation of cracks was correlated with the cooling rate of the melt pool as cracks tended to develop within finer grain structures, which were formed in a shorter solidification time and higher cooling rate.

This study presents the pioneering achievement of fabricating crack-free AA6061 parts using LFP without the necessity of preheating the substrate or mixing nanoparticles into the melt pool during the laser melting. The study includes a comprehensive examination of both the mechanical properties and grain structures, with comparisons made to parts produced through the traditional LPBF method.

The purpose of this paper, an experimental study, is to investigate the optimal machining parameters for turning of nickel-based superalloy Inconel 718 under eco-friendly nanofluid minimum quantity lubrication (NMQL) environment to minimize cutting tool flank wear (Vb) and machined surface roughness (Ra).

The central composite rotatable design approach under response surface methodology (RSM) is adopted to prepare a design of experiments plan for conducting turning experiments.

The optimum value of input turning parameters: cutting speed (A), feed rate (B) and depth of cut (C) is found as 79.88 m/min, 0.1 mm/rev and 0.2 mm, respectively, with optimal output response parameters: Vb = 138.633 µm and Ra = 0.462 µm at the desirability level of 0.766. Feed rate: B and cutting speed: A2 are the leading model variables affecting Vb, with a percentage contribution rate of 12.06% and 43.69%, respectively, while cutting speed: A and feed rate: B are the significant factors for Ra, having a percentage contribution of 38.25% and 18.03%, respectively. Results of validation experiments confirm that the error between RSM predicted and experimental observed values for Vb and Ra is 3.28% and 3.75%, respectively, which is less than 5%, thus validating that the formed RSM models have a high degree of conformity with the obtained experimental results.

The outcomes of this research can be used as a reference machining database for various metal cutting industries to establish eco-friendly NMQL practices during the turning of superalloy Inconel 718 to enhance cutting tool performance and machined surface integrity.

No study has been communicated till now on the turning of Inconel 718 under NMQL conditions using olive oil blended with multi-walled carbon nanotubes-based nanofluid.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-10-2023-0317/

The purpose of this study is to investigate the use of micro-pits technology to the problem of tribological performance in a sliding motion.

Vegetable oil is a sustainable and economically viable alternative to both mineral and synthetic oils, offering significant savings in both the cost of research and manufacturing. To solve the depriving issue and boost lubrication film thickness, the micro-pits on the surface may function as reservoirs that provide the oil to the contact inlet area. In this research, an aluminium block is used as the workpiece material in an evaluation of a through pin-on-disc tribotester. Lubricating oil in the form of super olein (SO) was used in the experiment.

The results show that the friction performance during a rubbing process between a hemispherical pin and an aluminium block lubricated with SO using aluminium alloy materials, AA5083, was significantly improved.

In this study, a material that breaks down called SO, which is derived from the fractionation of palm olein, was used to use a modified aluminium micro-pit sample that will serve as a lubricant reservoir in pin-on-disc tribotester.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0200/

The purpose of this study is to use polybenzoxazine (Pbz) functionalized ZrO₂ nanoparticles to synthesize polyurethane (PU)-PbZ/ZrO₂ nanocomposite. The results derived from the electrochemical impedance spectroscopy (EIS) and polarization studies indicated the superior anticorrosive activity of PU-Pbz/ZrO₂ nanocomposite coatings compared to those of plain PU coatings. The decreased corrosion current was detected on the scratch of the PU-Pbz/ZrO₂ nanocomposite-coated mild steel surface by scanning electrochemical microscopy (SECM) compared to other studied coatings. The superior anticorrosive and mechanical properties of the proposed nanocomposite coatings provide a new horizon in the development of high-performance anticorrosive coatings for various industries.

The Pbz functionalized ZrO₂ nanoparticles were characterized by Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive X-ray analysis (EDX) and thermogravimetric analysis (TGA) in terms of the structural, morphological and thermal properties of these coatings. A different formulation of coatings such as PU, PU-Pbz, PU-ZrO₂ and PU-Pbz/ZrO₂ were prepared and investigated for their corrosion protection performance on mild steel in natural seawater by electrochemical techniques. The surface morphological studies were done by SEM/EDX and XRD analysis.

The superior anticorrosive property of the proposed nanocomposite coatings provides a new horizon in the development of high-performance anticorrosive coatings for various industries. Addition of Pbz wrapped ZrO₂ nanoparticles into the PU coating resulted in the blockage of charge transfer at the metal/electrolyte interface, which reduced the dissolution of mild steel. It was revealed from the SEM/EDX analysis that the formation of the corrosion products at the metal/electrolyte interface behaved as the passive layer which reduced the dissolution of steel.

The inclusion of polybenzoxazine functionalized ZrO₂ nanoparticles to the polyurethane coating reinforces the barrier and mechanical properties of PU-Pbz/ZrO₂ nanocomposite, which is due to the synergistic effect of ZrO₂ and Pbz.

Composite materials are replacing the traditional materials because of their remarkable properties and the addition of nanoparticles making a new trend in material world. The nano addition effect on tribological properties is essential to be used in automotive and industrial applications. The current work investigates the sliding wear behavior of an aluminum alloy (AA) 6061-based hybrid metal matrix composites (HMMCs) reinforced with SiC and B₄C ceramic nanoparticles.

The hybrid composites are fabricated using stir casting process. Two different compositions were fabricated by varying the weight percentage of the ceramic reinforcements. An attempt has been made to study the wear and friction behavior of the composites using pin-on-disc tribometer to consider the effects of sliding speed, sliding distance and the normal load applied.

The tribological tests are carried out and the performances were compared. Increase in sliding speed to 500 rpm resulted in the rise of temperature of the contacting tribo-surface which intensified the wear rate at 30N load for the HMMC. The presence of the ceramic particles further reduced the contact region of the mating surface thus reducing the coefficient of friction at higher sliding speeds. Oxidation, adhesion, and abrasion were identified to be the main wear mechanisms which were further confirmed using energy dispersive spectroscopy and field emission scanning electron microscopy (FESEM) of the worn out samples.

The enhancement of wear properties is achieved because of the addition of the SiC and B₄C ceramic nanoparticles, in which these composites can be applied to automobile, aerospace and industrial products where the mating parts with less weight is required.

The influence of nanoparticles on the tribological performance is studied in detail comprising of two different ceramic particles which is almost new research. The sliding effect of hybrid composites with nano materials paves the way for using these materials in engineering and domestic applications.

The purpose of this paper is to provide industrial, education and academic users of computer programs a basic overview of finite elements in metal forming that will enable them to recognize the pitfalls of the existing formulations, identify the possible sources of errors and understand the routes for validating their numerical results.

The methodology draws from the fundamentals of the finite elements, plasticity and material science to aspects of computer implementation, modelling, accuracy, reliability and validation. The approach is illustrated and enriched with selected examples obtained from research and industrial metal forming applications.

The presentation is a step towards diminishing the gap being formed between developers of the finite element computer programs and the users having the know‐how on the metal forming technology. It is shown that there are easy and efficient ways of refreshing and upgrading the knowledge and skills of the users without resorting to complicated theoretical and numerical topics that go beyond their knowledge and most often are lectured out of metal forming context.

The overall content of the paper is enhancement of previous work in the field of sheet and bulk metal forming, and from experience in lecturing these topics to students in graduate and post‐graduate courses and to specialists of metal forming from industry.

The purpose of this paper is to investigate the impact of ultrasonic vibration (UV) and tool pin profile on mechanical properties and microstructural behaviour of AA7075-T651 and AA6061-T6 joints was analysed.

The joints were fabricated using three different tool pin profiles such as cylindrical, square and triangle. For each tool pin profile, two different UV powers of 1.5 kW and 2 kW were used.

On both the advancing and retreating sides of the weld, the thermo-mechanically affected zone has the lowest microhardness. In all joints, the tensile fracture locations match to the minimum hardness values. Field emission scanning electron microscope fractography of tensile tested specimens reveals heterogeneous modes of brittle, shear and ductile fracture. Three-point bending analysis was performed to determine the ductility and soundness of the weld joint. The acoustic softening effect of UV, as well as the static and dynamic ratio of tool pin profile, plays an important role in determining the material flow and mechanical behaviour of the joint.

Dissimilar aluminium joining fascinates many applications like aircraft, aerospace, automobiles, ship building and electronics, where fusion welding is a very intricate process because of the deviation in its physical and chemical properties.

From this study investigation, it is found that the square pin profiled tool with 2 kW UV power produces metallurgical defect-free and mechanically sound weld with maximum tensile strength, hardness and bending load of 297 MPa, 151HV and 3.82 kN, respectively.