Search results

This study aims to address the limited understanding of the complex correlations among strut size, structural orientation and process parameters in selective laser melting (SLM)-fabricated lattice structures. By investigating the effects of crucial process parameters, strut diameter and angle on the microstructure and mechanical performance of AlSi10Mg struts, the research seeks to enhance the surface morphologies, microstructures and mechanical properties of AM lattice structures, enabling their application in various engineering fields, including medical science and space technologies.

This comprehensive study investigates SLM-fabricated AlSi10Mg strut structures, examining the effects of process parameters, strut diameter and angle on densification behavior and microstructural characteristics. By analyzing microstructure, geometrical properties, melt pool morphology and mechanical properties using optical microscopy, scanning electron microscope, energy dispersive X-ray spectroscopy and microhardness tests, the research addresses existing gaps in knowledge on fine lattice strut elements and their impact on surface morphology and microstructure.

The study revealed that laser energy, power density and strut inclination angle significantly impact the microstructure, geometrical properties and mechanical performance of SLM-produced AlSi10Mg struts. Findings insight enable the optimization of SLM process parameters to produce lattice structures with enhanced surface morphologies, microstructures and mechanical properties, paving the way for applications in medical science and space technologies.

This study uniquely investigates the effects of processing parameters, strut diameter and inclination angle on SLM-fabricated AlSi10Mg struts, focusing on fine lattice strut elements with diameters as small as 200 µm. Unlike existing literature, it delves into the complex correlations among strut size, structural orientation and process parameters to understand their impact on microstructure, geometrical imperfections and mechanical properties. The study provides novel insights that contribute to the optimization of SLM process parameters, moving beyond the typically recommended guidelines from powder or machine suppliers.

The consolidation process and morphology evolution in ceramics-based additive manufacturing (AM) are still not well-understood. As a way to better understand the ceramic selective laser sintering (SLS), a dynamic three-dimensional computational model was developed to forecast thermal behavior of hydroxyapatite (HA) bioceramic.

AM has revolutionized automotive, biomedical and aerospace industries, among many others. AM provides design and geometric freedom, rapid product customization and manufacturing flexibility through its layer-by-layer technique. However, a very limited number of materials are printable because of rapid melting and solidification hysteresis. Melting-solidification dynamics in powder bed fusion are usually correlated with welding, often ignoring the intrinsic properties of the laser irradiation; unsurprisingly, the printable materials are mostly the well-known weldable materials.

The consolidation mechanism of HA was identified during its processing in a ceramic SLS device, then the effect of the laser energy density was studied to see how it affects the processing window. Premature sintering and sintering regimes were revealed and elaborated in detail. The full consolidation beyond sintering was also revealed along with its interaction to baseplate.

These findings provide important insight into the consolidation mechanism of HA ceramics, which will be the cornerstone for extending the range of materials in laser powder bed fusion of ceramics.

In this study, two postprocessing techniques, namely, conventional burnishing (CB) and ultrasonic-assisted burnishing (UAB), were applied to improve the fatigue behavior of 316 L stainless steel fabricated through selective laser melting (SLM). The effects of these processes on surface roughness, porosity, microhardness and fatigue performance were experimentally investigated. The purpose of this study is to evaluate the feasibility and effectiveness of ultrasonic-assisted burnishing as a preferred post-processing technique for enhancing the fatigue performance of additively manufactured components.

All samples were subjected to a sandblasting process. Next, the samples were divided into three distinct groups. The first group (as-Built) did not undergo any additional postprocessing, apart from sandblasting. The second group was treated with CB, while the third group was treated with ultrasonic-assisted burnishing. Finally, all samples were evaluated based on their surface roughness, porosity, microhardness and fatigue performance.

The results revealed that the initial mean surface roughness (Ra) of the as-built sample was 11.438 µm. However, after undergoing CB and UAB treatments, the surface roughness decreased to 1.629 and 0.278 µm, respectively. Notably, the UAB process proved more effective in eliminating near-surface pores and improving the microhardness of the samples compared to the CB process. Furthermore, the fatigue life of the as-built sample, initially at 66,000 cycles, experienced a slight improvement after CB treatment, reaching 347,000 cycles. However, the UAB process significantly enhanced the fatigue life of the samples, extending it to 620,000 cycles.

After reviewing the literature, it can be concluded that UAB will exceed the capabilities of CB in terms of enhancing the surface roughness and, subsequently, the fatigue performance of additive manufactured (AM) metals. However, the actual impact of the UAB process on the fatigue life of AM products has not yet been thoroughly researched. Therefore, in this study, this paper used the burnishing process to enhance the fatigue life of 316 L stainless steel produced through the SLM process.

Three-dimensional (3D) casting means using additive manufacturing (AM) techniques to print the mould for casting the cast tool. The printed mould, however, should be checked for its dimensional accuracy. 3D scanning can be used for the same. The purpose of this study is to combine the different AM techniques for 3D casting with 3D scanning to produce parts with close tolerance for preparing electrical discharge machining (EDM) electrodes.

The four processes, namely, stereolithography, selective laser sintering, fused deposition modelling and vacuum casting, are used to print the casting mould. The mould is designed in two halves, assembled to form a complete mould. The mould is 3D scanned in two stages: before and after using it as a casting mould. The mould's average and maximum dimensional deviations are calculated using 3D-scanned results. The eutectic Sn-Bi alloy is cast in the mould. The surface roughness of the mould and the cast tool are measured.

The cast tool is selected from the four processes in terms of dimensional accuracy and surface finish. The same is electroplated with copper. The microstructure of the cast tool (low-melting-point alloy) and deposited copper is analysed using a scanning electron microscope. Energy dispersive spectroscopy and X-ray diffraction techniques are used to verify the composition of the cast and coated alloy. The electroplated tool is finally tested on the EDM setup. The material removal rate and tool wear are measured. The performance is compared with a solid copper tool. The free-form customised EDM mould is also prepared, and the profile is cast out. The same is tested on the EDM. Thus, the developed path can be successfully used for rapid tooling applications.

The eutectic composition of Sn-Bi is cast in the 3D-printed mould using different AM techniques combined with 3D scanning quality to check its feasibility as an EDM electrode, which is a novel work and has not been done previously.

This paper aims to examine the static compression characteristics of cell topologies in body-centered cubic with vertical struts (BCCZ) and face-centered cubic with vertical struts (FCCZ) along with novel BCCZZ and FCCZZ lattice structures.

The newly developed structures were obtained by adding extra interior vertical struts into the BCCZ and FCCZ configurations. The samples, composed of the AlSi10Mg alloy, were fabricated using the selective laser melting (SLM) additive manufacturing technique. The specific compressive strength and failure behavior of the manufactured lattice structures were investigated, and comparative analysis among them was done.

The results revealed that the specific strength of BCCZZ and FCCZZ samples with 0.5 mm strut diameter exhibited approximately a 23% and 18% increase, respectively, compared with the BCCZ and FCCZ samples with identical strut diameters. Moreover, finite element analysis was carried out to simulate the compressive response of the lattice structures, which could be used to predict their strength and collapse mode. The findings showed that while the local buckling of lattice cells is the major failure mode, the samples subsequently collapsed along a diagonal shear band.

An original and systematic investigation was conducted to explore the compression properties of newly fabricated lattice structures using SLM. The results revealed that the novel FCCZZ and BCCZZ structures were found to possess significant potential for load-bearing applications.

This paper aims to investigate the differences in hot corrosion behavior of the GTD222 superalloy and TiC/GTD222 composite in a mixed salt of 75% Na₂SO₄ and 25% K₂SO₄ at 900°C.

The GTD222 superalloy and TiC/GTD222 nickel-based composite were prepared using selective laser melting (SLM). Subsequently, the hot corrosion behavior of the two alloys was systematically investigated in a salt mixture consisting of 75% Na₂SO₄ and 25% K₂SO₄ (Wt.%) at 900°C.

The TiC/GTD222 composite exhibited better hot corrosion resistance compared to the GTD222 superalloy. First, the addition of alloying elements led to the formation of a protective oxide film on the TiC/GTD222 composites 20 h before hot corrosion. Second, TiC/GTD222 composite corrosion surface has a higher Ti content, after 100 h of hot corrosion, the composite corrosion surface Ti content of 10.8% is more than two times the GTD222 alloy 4% Ti. The Ti and Cr oxides are tightly bonded, effectively resisting the erosion of corrosive elements.

The hot corrosion behavior of GTD222 superalloy and TiC/GTD222 composites prepared by SLM in a mixed salt of 75% Na₂SO₄ and 25% K₂SO₄ was studied for the first time. This study provides insights into the design of high-temperature alloys resistant to hot corrosion.

This study aims to investigate the wetting behavior of AgCuTi and AgCu filler metals on selective laser melting (SLMed) Ti/TiB₂, and to analyze the microstructure and fracture characteristics of SLMed Ti/TiB₂/AgCuTi or AgCu alloy/SLMed Ti/TiB₂ brazed joints. The wetting behavior of AgCuTi and AgCu filler metals on the selective laser melted (SLMed) Ti/TiB₂ has been studied. The analysis of microstructures and fracture characteristics in vacuum-brazed SLMed Ti/TiB₂ substrate, using AgCuTi and AgCu filler metals, has been conducted to elucidate the influence of brazing temperature and alloy composition on the shear strength of the brazed joints.

Brazing SLMed-Ti/TiB₂ in a vacuum using AgCuTi and AgCu filler metals, this study aims to explore the optimal parameters for brazed joints at various brazing temperatures (800°C−950°C).

The findings suggest that elevated brazing temperatures lead to a more extensive diffusion region in the joint as a result of the partial melting of the filler metal. The joint composition changes from distinct Ti₂Cu layer/TiCu layer/filler metal to a-Ti (ss) + ß-Ti (ss)/TiCu. As the brazing temperature increases, the fracture mode shifts from brittle cleavage to ductile fracture, mainly attributed to a decrease in the CuTi within the brazed joint. This change in fracture behavior indicates an improvement in the ductility and toughness of the joint.

The originality of this study lies in the comprehensive analysis of the microstructure and shear strength of vacuum brazing SLMed Ti/TiB₂ using AgCuTi and AgCu filler metals.

The purpose of this paper is to determine the ultra-high cycle fatigue behavior and ultra-slow crack propagation behavior of selective laser melting (SLM) AlSi7Mg alloy under as-built conditions.

Constant amplitude and two-step variable amplitude fatigue tests were carried out using ultrasonic fatigue equipment. The fracture surface of the failure specimen was quantitatively analyzed by scanning electron microscope (SEM).

The results show that the competition of surface and interior crack initiation modes leads to a duplex S–N curve. Both manufacturing defects (such as the lack of fusion) and inclusions can act as initially fatal fatigue microcracks, and the fatigue sensitivity level decreases with the location, size and type of the maximum defects.

The research results play a certain role in understanding the ultra-high cycle fatigue behavior of additive manufacturing aluminum alloys. It can provide reference for improving the process parameters of SLM technology.

This paper aims to present spot pattern welding (SPW) as a scanning strategy for laser-foil-printing (LFP) additive manufacturing (AM) in place of the previously used continuous pattern welding (CPW) (line-raster scanning). The SPW strategy involves generating a sequence of overlapping spot welds on the metal foil, allowing the laser to form dense and uniform weld beads. This in turn reduces thermal gradients, promotes material consolidation and helps mitigate process-related risks such as thermal cracking, porosity, keyholing and Marangoni effects.

304L stainless steel (SS) feedstock is used to fabricate test specimens using the LFP system. Imaging techniques are used to examine the melt pool dimensions and layer bonding. In addition, the parts are evaluated for residual stresses, mechanical strength and grain size.

Compared to CPW, SPW provides a more reliable heating/cooling relationship that is less dependent on part geometry. The overlapping spot welds distribute heat more evenly, minimizing the risk of elevated temperatures during the AM process. In addition, the resulting dense and uniform weld beads contribute to lower residual stresses in the printed part.

To the best of the authors’ knowledge, this is the first study to thoroughly investigate SPW as a scanning strategy using the LFP process. In general, SPW presents a promising strategy for securing embedded sensors into LFP parts while minimizing residual stresses.

Surface quality and porosity significantly influence the structural and functional properties of the final product. This study aims to establish and explain the underlying relationships among processing parameters, top surface roughness and porosity level in additively manufactured 316L stainless steel.

A systematic variation of printing process parameters was conducted to print cubic samples based on laser power, speed and their combinations of energy density. Melt pool morphologies and dimensions, surface roughness quantified by arithmetic mean height (Sa) and porosity levels were characterized via optical confocal microscopy.

The study reveals that the laser power required to achieve optimal top surface quality increases with the volumetric energy density (VED) levels. A smooth top surface (Sa < 15 µm) or a rough surface with humps at high VEDs (VED > 133.3 J/mm³) can serve as indicators for fully dense bulk samples, while rough top surfaces resulting from melt pool discontinuity correlate with high porosity levels. Under insufficient VED, melt pool discontinuity dominates the top surface. At high VEDs, surface quality improves with increased power as mitigation of melt pool discontinuity, followed by the deterioration with hump formation.

This study reveals and summarizes the formation mechanism of dominant features on top surface features and offers a potential method to predict the porosity by observing the top surface features with consideration of processing conditions.