Search results

In pursuit of affordable and nutrient-rich food alternatives, the symbiotic culture of bacteria and yeast (SCOBY) emerged as a selected food ink for 3D printing. The purpose of this paper is to harness SCOBY’s potential to create cost-effective and nourishing food options using the innovative technique of 3D printing.

This work presents a comparative analysis of the printability of SCOBY with blends of wheat flour, with a focus on the optimization of process variables such as printing composition, nozzle height, nozzle diameter, printing speed, extrusion motor speed and extrusion rate. Extensive research was carried out to explore the diverse physical, mechanical and rheological properties of food ink.

Among the ratios tested, SCOBY, with SCOBY:wheat flour ratio at 1:0.33 exhibited the highest precision and layer definition when 3D printed at 50 and 60 mm/s printing speeds, 180 rpm motor speed and 0.8 mm nozzle with a 0.005 cm³/s extrusion rate, with minimum alteration in colour.

Food layered manufacturing (FLM) is a novel concept that uses a specialized printer to fabricate edible objects by layering edible materials, such as chocolate, confectionaries and pureed fruits and vegetables. FLM is a disruptive technology that enables the creation of personalized and texture-tailored foods, incorporating desired nutritional values and food quality, using a variety of ingredients and additions. This research highlights the potential of SCOBY as a viable material for 3D food printing applications.

The goal of this study is to determine the values of the process parameters that should be used during the machining of ceramic tile using the abrasive water jet (AWJ) process in order to achieve the lowest possible values for surface roughness and kerf taper angle.

In the present work, ceramic tile is processed by the AWJ process and experimental data were recorded using the RSM approach based Box–Behnken design matrix. The input process factors were water jet pressure, jet traverse speed, abrasive flow rate and standoff distance, to determine the surface roughness and kerf taper angle. ANOVA was used to check the adequacy of model and significance of process parameters. Further, the elite opposition-based learning grasshopper optimization (EOBL-GOA) algorithm was implemented to identify the simultaneous optimization of multiple responses of surface roughness and kerf taper angle in AWJ.

The suggested EOBL-GOA algorithm is suitable for AWJ of ceramic tile, as evidenced by the error rate of ±2 percent between experimental and predicted solutions. The surfaces were evaluated with an SEM to assess the quality of the surface generated with the optimal settings. As compared with initial setting of the SEM image, it was noticed that the bottom cut surface was nearly smooth, with less cracks, striations and pits in the improved optimal results of the SEM image. The results of the analysis can be used to control machining parameters and increase the accuracy of AWJed components.

The findings of this study present an innovative method for assessing the characteristics of the nontraditional machining processes that are most suited for use in industrial and commercial applications.

The purpose of this paper is to adopt the multi-objective optimization technique for identifying a set of optimum abrasive water jet machining (AWJM) parameters to achieve maximum material removal rate (MRR) and minimum surface roughness.

Data of a few experiments as per the Taguchi’s orthogonal array are considered for achieving maximum MRR and minimum surface roughness (Ra) of the Inconel718. Analysis of variance is performed to understand the statistical significance of AWJM input process parameters.

Empirical relations are developed for MRR and Ra in terms of the AWJM process parameters and demonstrated their adequacy through comparison of test results.

The signal-to-noise ratio transformation should be applied to take in to account the scatter in the repetition of tests in each test run. But, many researchers have adopted this transformation on a single output response of each test run, which has no added advantage other than additional computational task. This paper explains the impact of insignificant process parameter in selection of optimal process parameters. This paper demands drawbacks and complexity in existing theories prior to use new algorithms.

Taguchi approach is quite simple and easy to handle optimization problems, which has no practical implications (if it handles properly). There is no necessity to hunt for new algorithms for obtaining solution for multi-objective optimization AWJM process.

This paper deals with a case study, which demonstrates the simplicity of the Taguchi approach in solving multi-objective optimization problems with a few number of experiments.

This paper aims to determine the optimum parametric settings for yielding superior mechanical properties, namely, ultimate tensile strength (UTS), yield strength (YS) and percentage elongation (EL) of AZ91D/AgNPs/TiO₂ hybrid composite fabricated by friction stir processing.

An empirical model has been developed to govern crucial influencing parameters, namely, rotation speed (RS), tool transverse speed (TS), number of passes (NPS) and reinforcement fraction (RF) or weight percentage. Box Behnken design (BBD) with four input parameters and three levels of each parameter was used to design the experimental work, and analysis of variance (ANOVA) was used to check the acceptability of the developed model. Desirability function analysis (DFA) for a multiresponse optimization approach is integrated with response surface methodology (RSM). The individual desirability index (IDI) was calculated for each response, and a composite desirability index (CDI) was obtained. The optimal parametric settings were determined based on maximum CDI values. A confirmation test is also performed to compare the actual and predicted values of responses.

The relationship between input parameters and output responses (UTS, YS, and EL) was investigated using the Box-Behnken design (BBD). Silver nanoparticles (AgNPs) and nano-sized titanium dioxide (TiO₂) enhanced the ultimate tensile strength and yield strength. It was observed that the inclusion of AgNPs led to an increase in ductility, while the increase in the weight fraction of TiO₂ resulted in a decrease in ductility.

AZ91D/AgNPs/TiO₂ hybrid composite finds enormous applications in biomedical implants, aerospace, sports and aerospace industries, especially where lightweight materials with high strength are critical.

In terms of optimum value through desirability, the experimental trials yield the following results: maximum value of UTS (318.369 MPa), maximum value of YS (200.120 MPa) and EL (7.610) at 1,021 rpm of RS, 70 mm/min of TS, 4 NPS and level 3 of RF.

This study aims to analyse the changes in mechanical and wear performance of aluminium alloy when yttrium oxide particles are incorporated. The microstructures are studied to analyse the change in the grain structures. Worn surfaces are observed via scanning electron microscope to study the wear mechanism in detail.

Stir casting is used to incorporate varying composition of yttrium particles, having an average particle size of 25 micrometer, in aluminium alloy 6063 matrix. Wear testing is carried out by DUCOM manufactured high temperature rotatory tribometer, and an indentation test is used for analysing the microhardness of the fabricated samples.

Microhardness of the material is increased with the increasing content of particulate addition. With the increasing content of reinforcement, more refined grains are produced. The load is transferred from the matrix to more rigid yttrium oxide particles. These factors contributed to escalated microhardness of the reinforced samples. Particulate addition enhanced the wear performance of the material; this might be attributed to increased microhardness and formation of an oxide layer.

Aluminium composites are finding wide applications in various industries, and there is always a requirement of material with enhanced tribological properties. Yttrium oxide particles exhibit improved mechanical properties, and their interaction with the aluminium matrix has not been studied much in the past. So, in this work, yttrium oxide incorporated aluminium matrix is studied.

This experimental study aims to deal with the improvement of process performance of electric discharge drilling (EDD) for fabricating true blind holes in titanium alloy Ti6Al4V. Micro EDD was performed on Ti6Al4V and blind holes were drilled into the workpiece.

The effects of input parameters (i.e. voltage, capacitance and spindle speed) on responses (i.e. material removal rate, tool wear rate and surface roughness [SR]) were evaluated through response surface methodology. The data was analyzed using analysis of variance and multi-optimization was performed for the optimized set of parameters. The optimized process parameters were then used to drill deeper blind holes.

Blind holes have few characteristics such as SR, taper angle and corner radius. The value of corner radius reflects the quality of the hole produced as well as the amount of tool roundness. The optimized process parameters suggested by the current experimental study lower down the response values (i.e. SR, taper angle and corner radius). The process is found very effective in producing finished blind holes.

This experimental study establishes EDD as a feasible process for the fabrication of truly blind holes in Ti6Al4V.

The aviation field requires a material with the ability to withstand severe environmental conditions. The purpose of this paper is to provide higher wear resistance and improve the lifetime of aircraft. Hence, it is vital to enhance the wear resistance and strength of the material.

In this investigation, the Az91D magnesium alloy was reinforced with lanthanum (La₂O₃) and cerium oxide (CeO₂) nanoparticles by stir casting and heat treatment process and the tribological and mechanical properties were analyzed.

The results showed the Az91D/CeO₂ composite exhibited higher density (1.96 g/cm3) and lower porosity (1.01%) compared to other materials due to the diffusion of CeO₂ nanoparticles in between the atoms of Az91D alloy. The hardness of Az91D/ CeO₂ & Az91D/ La₂O₃ was improved by 38% and 34%, respectively, compared to Az91D alloy owing to the reinforcing effect of hard nanoparticles. Further, the inclusion of nanoparticles decreased the mass loss and showed lower wear rate compared to the Az91D alloy due to the pinning effect of nanoparticles. In addition, the friction coefficient was observed in the order of Az91D > Az91D/ La₂O₃ > Az91D/ CeO₂. Moreover, the heat treatment displayed positive results on the properties of all the materials.

This work is original as the combination of cerium oxide nanoparticles with Az91D magnesium alloy is not tried by earlier investigators. Further, the comparative performance of both lanthanum and cerium oxide nanoparticles on the tribological and mechanical behavior of Az91D alloy has been analyzed for aviation application. This study will provide new information to the scientific world to increase the lifetime of aviation structures.

This study aims to investigate the corrosion behavior of stir-cast hybrid aluminum composite reinforced with CeO₂ and graphene nanoplatelets (GNPs) nanoparticulates used as cylinder liner material in the engines (automotive, aerospace and aircraft industries).

The composites were prepared using the stir-casting technique, and their microstructure and corrosion behavior was evaluated using scanning electron microscopy (SEM) and potentiodynamic polarization test, respectively.

The results showed that the addition of CeO₂ and GNPs improved the corrosion resistance of the composites, and the optimal combination of these two nanoparticles was found to be 3 wt.% CeO₂ and 3 wt.% GNPs. The enhanced corrosion resistance was attributed to the formation of a protective layer on the surface of the composite, as well as the effective dispersion and uniform distribution of nanoparticles in the matrix. The 0.031362 was noted as the lowest corrosion rate (mmpy) and was noticed in 94% Al-6061 alloy + (3 Wt.% CeO₂ + 3 Wt.% GNPs) sample at room temperature and at elevated temperatures; the corrosion rate (mmpy) was observed as 0.0601 and 0.0636 at 45 °C and 75 °C, respectively.

In the vast majority of the published research publications, either cerium oxide or graphene nanoplatelets were utilized as a single reinforcement or in conjunction with other types of reinforcement such as alumina, silicon carbide, carbon nano-tubes, tungsten carbide, etc., but on the combination of the CeO₂ and GNPs as reinforcements have very less literatures with 2 wt.% each only. The prepared hybrid aluminum composite (reinforcing 1 wt.% to 3 wt.% in Al-6061 alloy) was considered for replacing the cylinder liner material in the piston-cylinder arrangement of engines.

This paper aims to provide a detailed review of various cutting fluids (CFs).

Friction and wear are inevitable in machine parts in motion. The industrial sector uses various kinds of lubricants, which include engine oils, CFs, hydraulic fluids, greases, etc. to control friction and wear. The main purpose of using CF is to remove heat produced during machining and to reduce cutting forces, tool wear and energy associated with it. Thus, it increases the productivity and quality of the manufacturing process. But more than 80% of the CFs used in the industries now are mineral oil-based. These mineral oils and additives are highly undesirable because of their toxicity, nonbiodegradability, pollution and ecological problems. Hence, these petroleum-based oils in the lubrication system can be substituted with alternatives such as vegetable-based CF. Several studies are being conducted in the field of eco-friendly CFs. Because of the variance in fatty acid profile and availability, the selection of vegetable oils (VOs) is another problem faced nowadays. The present study is focused on bio-based oils and many eco-friendly additives. Various machining processes and comparisons relating to the same have also been made. The aim is to minimize the use of mineral oil and thereby introduce sustainability in production.

In this present study, bio-based oils, additives and various characteristic behavior of them in machining are being discussed. The VOs are found to be a potential base oil for industrial CFs.

This paper describes the importance of sustainable CFs.

The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid.

The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism.

Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool

A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.