Search results

This paper aims to introduce a novel method for the analysis of open cell porous components fabricated by laser-based powder bed metal additive manufacturing (AM) for the purpose of quality control. This method uses photogrammetric analysis, the extraction of geometric information from an image through the use of algorithms. By applying this technique to porous AM components, a rapid, low-cost inspection of geometric properties such as material thickness and pore size is achieved. Such measurements take on greater importance, as the production of porous additive manufactured orthopaedic devices increases in number, causing other, slower and more expensive methods of analysis to become impractical.

Here the development of the photogrammetric method is discussed and compared to standard techniques including scanning electron microscopy, micro computed tomography scanning and the recently developed focus variation (FV) imaging. The system is also validated against test graticules and simple wire geometries of known size, prior to the more complex orthopaedic structures.

The photogrammetric method shows an ability to analyse the variability in build fidelity of AM porous structures for use in inspection purposes to compare component properties. While measured values for material thickness and pore size differed from those of other techniques, the new photogrammetric technique demonstrated a low deviation when repeating measurements, and was able to analyse components at a much faster rate and lower cost than the competing systems, with less requirement for specific expertise or training.

The advantages demonstrated by the image-based technique described indicate the system to be suitable for implementation as a means of in-line process control for quality and inspection applications, particularly for high-volume production where existing methods would be impractical.

This paper aims to investigate the wear behaviour of different materials for cylinder liners and piston rings in a linear reciprocating tribometer with special focus on the wear of the cylinder liner in the boundary lubrication regime.

Conventional nitrided steel, as well as diamond-like carbon and chromium nitride-coated piston rings, were tested against cast iron, AlSi and Fe-coated AlSi cylinder liners. The experiments were carried out with samples produced from original engine parts to have the original surface topography available. Radioactive tracer isotopes were used to measure cylinder liner wear continuously, enabling separation of running-in and steady-state wear.

A ranking of the material pairings with respect to wear behaviour of the cylinder liner was found. Post-test inspection of the cylinder samples by scanning electron microscopy (SEM) revealed differences in the wear mechanisms for the different material combinations. The results show that the running-in and steady-state wear of the liners can be reduced by choosing the appropriate material for the piston ring.

The use of original engine parts in a closely controlled tribometer environment under realistic loading conditions, in conjunction with continuous and highly sensitive wear measurement methods and a detailed SEM analysis of the wear mechanisms, forms an intermediate step between engine testing and laboratory environment testing.

This scientific article aims to evaluate the efficacy of the drug Doxorubicin for treating hepatocellular carcinoma (HCC) in Egypt. The study analyzes data from patients referred to a multi-disciplinary consultation at the National Cancer Institute, Cairo University. The study includes 40 intermediate-stage HCC patients who underwent treatment with either Doxorubicin-Lipiodol or Doxorubicin-loaded drug-eluting beads-trans-arterial chemoembolization (DEB-TACE).

Patients referred to a multi-disciplinary consultation at the National Cancer Institute, Cairo University with a possible diagnosis of HCC in the intermediate stage were eligible for the study.

The study finds that the plasma peak concentration of Doxorubicin is significantly higher in patients treated with Lipiodol compared to those treated with DEB-TACE. The median plasma peak concentration of patients treated with Lipiodol was significantly higher 424 (202.5–731) than the peak level of patients treated with beads 84.95 (26.6–156.5) with p-value = 0.036. However, there is no significant difference in other pharmacokinetic parameters between the two treatment groups. The research article also investigates the genetic polymorphisms in HCC patients treated with Doxorubicin-Lipiodol and Doxorubicin-loaded DEB-TACE. It identifies a significant association between the ABCB1 gene (C3435T) and the concentration of Doxorubicin in plasma. Patients with the CCand computed tomography (CT) genotypes of ABCB1 have higher concentrations of Doxorubicin compared to those with the TT genotype. Furthermore, the study examines the progression-free survival rates and tumour response in the two treatment groups. It demonstrates that DEB-TACE patients have a higher progression-free survival rate compared to cTACE patients. DEB-TACE also leads to better tumour regression.

The current study helps to increase the understanding of the genetic factors that may contribute to HCC susceptibility in the Egyptian population. However, it is essential to consider that genetic polymorphism is just one aspect of HCC risk, and other factors such as environment, lifestyle and viral infections also play crucial roles. Further research is needed to elucidate the complex interactions between genetic and environmental factors in HCC development among Egyptians.

As an advanced manufacturing method, additive manufacturing (AM) technology provides new possibilities for efficient production and design of parts. However, with the continuous expansion of the application of AM materials, subtractive processing has become one of the necessary steps to improve the accuracy and performance of parts. In this paper, the processing process of AM materials is discussed in depth, and the surface integrity problem caused by it is discussed.

Firstly, we listed and analyzed the characterization parameters of metal surface integrity and its influence on the performance of parts and then introduced the application of integrated processing of metal adding and subtracting materials and the influence of different processing forms on the surface integrity of parts. The surface of the trial-cut material is detected and analyzed, and the surface of the integrated processing of adding and subtracting materials is compared with that of the pure processing of reducing materials, so that the corresponding conclusions are obtained.

In this process, we also found some surface integrity problems, such as knife marks, residual stress and thermal effects. These problems may have a potential negative impact on the performance of the final parts. In processing, we can try to use other integrated processing technologies of adding and subtracting materials, try to combine various integrated processing technologies of adding and subtracting materials, or consider exploring more efficient AM technology to improve processing efficiency. We can also consider adopting production process optimization measures to reduce the processing cost of adding and subtracting materials.

With the gradual improvement of the requirements for the surface quality of parts in the production process and the in-depth implementation of sustainable manufacturing, the demand for integrated processing of metal addition and subtraction materials is likely to continue to grow in the future. By deeply understanding and studying the problems of material reduction and surface integrity of AM materials, we can better meet the challenges in the manufacturing process and improve the quality and performance of parts. This research is very important for promoting the development of manufacturing technology and achieving success in practical application.

Children living in agricultural areas are exposed to pesticides in their living areas and through activities of daily living. These exposures may lead to adverse health effects. The purpose of this paper is to investigate household environmental and behavioural factors associated with chlorpyrifos exposure and resultant adverse health effects in children living in an agricultural community.

A cross-sectional study was conducted including 65 toddlers (age of 12–36 months) and their parents were face-to-face interviewed from January to February 2016. Toddler’s hands and feet, toys and floors were wiped for chlorpyrifos residue analysis. The wipes were extracted and analysed by gas chromatography with a flame photometric detector, and blood cholinesterase activity was measured by the EQM Test-mate (model 400).

The average age (± standard deviation) of children was 19.9 (±5.9) months. Chlorpyrifos detections were 61.5 per cent (hands), 57.1 per cent (toys), 53.8 per cent (floors) and 30.8 per cent (feet). The highest chlorpyrifos residue concentration was detected on toy surface (3.022 µg/m²). Chlorpyrifos residues on hands and feet were positively correlated with concentrations on floors and toys (Spearman’s ρ, p<0.01). Multiple linear regression analysis revealed that more frequent hand washing (β=−0.236, p=0.067) and showering (β=−0.240, p=0.056) was negatively associated with chlorpyrifos residue on children’s body. House cleaning frequency was significantly associated with an increase in haemoglobin-adjusted erythrocyte cholinesterase (β=0.251, p<0.05).

Chlorpyrifos exposures found in the children household area through their activities and behaviours can cause several adverse health effects. The circumstances associated with chlorpyrifos exposure should be mitigated and reduced to improve the household environment of children living agricultural areas.

The purpose of this paper is to investigate epidemiology and control strategies of the four priority vector-borne diseases (VBDs) in Nepal, i.e. malaria, Kala-azar (visceral leishmaniasis), lymphatic filariasis (LF) and dengue fever/dengue hemorrhagic fever.

The study was a retrospective design to collect data during 1998–2016 from VBDs endemic districts of Nepal. All data were reviewed and epidemiological information of the four VBDs were analyzed.

The number of malaria cases during 1998–2016 of the 13 affected districts was declined from 8,498 to 991 cases with no record of deaths since 2012. The number of cases and deaths in the 12 kala-azar (visceral leishmaniasis) affected districts in 1998 was 1,409 and 42 cases, respectively, but was dramatically decreased in 2016 to 213 and 2 cases, respectively. LF cases of the 61 affected districts in 2011, 2014 and 2016 were 28,855, 30,000 and 33,517 cases, respectively. In total, 25 districts achieved elimination target and the remaining are expected to complete the needful cycles by 2018. Dengue incidence of the 31 affected districts during 2006–2015 was under controlled with reported cases of 642, 356 and 136 cases in 2013, 2014 and 2015, respectively, and only one death in 2015. Implementation of control strategies particularly disease management and community peoples’ awareness significantly reduced the cases and deaths of the target VBDs.

The results of this study clearly suggest that the current control strategies have been worked effectively. However, in particular of the VBDs, health education in communities in the endemic areas should be adopted for better community participation in the context of the primary health care approach and increase the effectiveness of disease control.

VBDs, i.e., malaria, kala-azar (visceral leishmaniasis), LF and dengue fever/dengue hemorrhagic fever, are major causes of morbidity and mortality in the least developed countries which include Nepal. Globalization of travel and trading, unplanned urbanization, environmental and climate change are having a significant impact on disease transmission. Therefore, the Ministry of Health of Nepal had brought some changes in strategies based on activities for disease control, vector control, preventive and preparedness for outbreak response. Consequently, the cases and deaths due to malaria, kala-azar (visceral leishmaniasis), lymphatic filaiasis and dengue fever/dengue hemorrhagic fever have been brought down markedly.

Porous implant surface is shown to facilitate bone in-growth and cell attachment, improving overall osteointegration, while providing adequate mechanical integrity. Recently, biodegradable material possessing such superior properties has been the focus with an aim of revolutionizing implant’s design, material and performance. This paper aims to present a comprehensive investigation into the design and development of low elastic modulus porous biodegradable Mg-3Si-5HA composite by mechanical alloying and spark plasma sintering (MA-SPS) technique.

This paper presents a comprehensive investigation into the design and development of low elastic modulus porous biodegradable Mg-3Si-5HA composite by MA-SPS technique. As the key alloying elements, HA powders with an appropriate proportion weight 5 and 10 are mixed with the base elemental magnesium (Mg) particles to form the composites of potentially variable porosity and mechanical property. The aim is to investigate the performance of the synthesized composites of Mg-3Si together with HA in terms of mechanical integrity hardness and Young’s moduli corrosion resistance and in-vitro bioactivity.

Mechanical and surface characterization results indicate that alloying of Si leads to the formation of fine Mg2 Si eutectic dense structure, hence increasing hardness while reducing the ductility of the composite. On the other hand, the allying of HA in Mg-3Si matrix leads to the formation of structural porosity (5-13 per cent), thus resulting in low Young’s moduli. It is hypothesized that biocompatible phases formed within the composite enhanced the corrosion performance and bio-mechanical integrity of the composite. The degradation rate of Mg-3Si composite was reduced from 2.05 mm/year to 1.19 mm/year by the alloying of HA elements. Moreover, the fabricated composites showed an excellent bioactivity and offered a channel/interface to MG-63 cells for attachment, proliferation and differentiation.

Overall, the findings suggest that the Mg-3Si-HA composite fabricated by MA and plasma sintering may be considered as a potential biodegradable material for orthopedic application.

This paper aims to gain an understanding of the behaviour of iron ore when melted by a laser beam in a continuous manner. This fundamental knowledge is essential to further develop additive manufacturing routes such as production of low cost parts and in-situ reduction of the ore during processing.

Blown powder directed energy deposition was used as the processing method. The process was observed through high-speed imaging, and computed tomography was used to analyse the specimens.

The experimental trials give preliminary results showing potential for the processability of iron ore for additive manufacturing. A large and stable melt pool is formed in spite of the inhomogeneous material used. Single and multilayer tracks could be deposited. Although smooth and even on the surface, the single layer tracks displayed porosity. In case of multilayered tracks, delamination from the substrate material and deformation can be seen. High-speed videos of the process reveal various process phenomena such as melting of ore powder during feeding, cloud formation, melt pool size, melt flow and spatter formation.

Very little literature is available that studies the possible use of ore in additive manufacturing. Although the process studied here is not industrially useable as is, it is a step towards processing cheap unprocessed material with a laser beam.

The paper targets on providing new experimental data for validation of the well-established mathematical models within the framework of the lattice Boltzmann method (LBM), which are applied to problems of casting processes in complex mould cavities.

An experimental campaign aiming at the free-surface flow within a system of narrow channels is designed and executed under well-controlled laboratory conditions. An in-house lattice Boltzmann solver is implemented. Its algorithm is described in detail and its performance is tested thoroughly using both the newly recorded experimental data and well-known analytical benchmark tests.

The benchmark tests prove the ability of the implemented algorithm to provide a reliable solution when the surface tension effects become dominant. The convergence of the implemented method is assessed. The two new experimentally studied problems are resolved well by simulations using a coarse computational grid.

A detailed set of original experimental data for validation of computational schemes for simulations of free-surface gravity-driven flow within a system of narrow channels is presented.

The purpose of this study is to verify how the carbon doping of the WC-Co cemented carbide (CC) affected their structure before their processing by hot isostatic pressing (HIP) technology.

The samples for this experiment were fabricated by selective laser melting technology (SLM) using a YAG fiber laser with a power of P = 40 W and a scanning speed of 83 mm/s. The subsequent carbon doping process was performed in a chamber furnace at 900 0 C for 1, 4 and 12 h. The HIP was performed at 1,390°C and pressures of 40 MPa, 80 MPa and 120 MPa. The changes induced in the structures were evaluated using X-ray diffraction and various microscopic methods.

X-ray diffraction analysis showed that the structure of the samples after SLM consisted of WC, W₂C, Co₄W₂C and Co phases. As a result of the increase in the carbon content in the structure of the samples, the transition carbide W₂C and structural phase Co₄W₂C decayed. Their decay was manifested by the coarsening of the minor alpha phase (WC), which occurred both during the carburizing process and during the subsequent processing using HIP. In the samples in which the structure was carburized prior to HIP, only the structural phases WC and Co were observed in most cases.

The results confirm that it is possible to increase the homogeneity of the CC structure and thus its applicability in practice by additional carburization of the sample structure with subsequent processing by HIP technology.