Search results

Taking a 2,000 r/min 10 kW permanent magnet motor as an example, the purpose of this paper is to study the influence of driving modes on the performance of permanent magnet motor at limit conditions, and researched the variation mechanism of motor performance influenced by different driving modes.

A two-dimensional electromagnetic field model of the permanent magnet motor was established, and a rectangular-wave driving circuit was built. By using the finite element method, the electromagnetic field, current, harmonic content and eddy current loss were calculated when the motor operated at rated load and limit load. On the basis of the motor loss calculation, the temperature field of the motor operating at rated condition and limit condition was researched, and the factors that influence motor limit overload capacity were analyzed. By analyzing the motor loss variation at different load conditions, the change mechanism of the motor temperature field was determined further. Combined with the related experiments, the correctness of the above analysis was verified.

Permanent magnet synchronous motor (PMSM) driven by sine wave is better compared with brushless direct current motor (BLDCM) driven by rectangular wave in reducing the magnetic field harmonics, motor losses and optimizing the temperature distribution in the motor. The method driven by sine wave could improve the motor output performance including the motor efficiency and the motor overload capacity. The winding temperature is the most important factor that limits the output capability of PMSM operating for a long time. However, because of the large rotor eddy current losses, the permanent magnet temperature is the most important factor that limits the output capability of BLDCM operating for a long time.

The influence of driving modes on the motor magnetic field, losses and temperature distribution, efficiency and overload capacity was determined, and the influence mechanism was also analyzed. Combined with the analysis of the electromagnetic and temperature fields, the advantages of different driving modes were presented. This study could provide an important basis for the design of permanent magnet motors with different driving modes, and it also provides reference for the application of permanent magnet motor.

This paper presents the influence of driving modes on permanent magnet motors. The limit output capacity of the motor with different driving modes was studied, and the key factors limiting the motor output capability were obtained.

An appropriate equivalent model is the key to the effective analysis of the system and structure in which permanent magnet takes part. At present, there are several equivalent models for calculating the interacting magnetic force between permanent magnets including magnetizing current, magnetic charge and magnetic dipole–dipole model. How to choose the most appropriate and efficient model still needs further discussion.

This paper chooses cuboid, cylindrical and spherical permanent magnets as calculating objects to investigate the detailed calculation procedures based on three equivalent models, magnetizing current, magnetic charge and magnetic dipole–dipole model. By comparing the accuracies of those models with experiment measurement, the applicability of three equivalent models for describing permanent magnets with different shapes is analyzed.

Similar calculation accuracies of the equivalent magnetizing current model and magnetic charge model are verified by comparison between simulation and experiment results. However, the magnetic dipole–dipole model can only accurately calculate for spherical magnet instead of other nonellipsoid magnets, because dipole model cannot describe the specific characteristics of magnet's shape, only sphere can be treated as the topological form of a dipole, namely a filled dot.

This work provides reference basis for choosing a proper model to calculate magnetic force in the design of electromechanical structures with permanent magnets. The applicability of different equivalent models describing permanent magnets with different shapes is discussed and the equivalence between the models is also analyzed.

The purpose of this paper is the investigation of eddy currents induced in the axial‐flux permanent‐magnet machine housing by the leakage flux and the introduction of permanent magnets in the steady‐state AC finite‐element analysis and coupling their effects with the transient thermal analysis.

The proposed approach is based on the finite‐element method as well as on using the basic analytical equations. The approach was first applied in the magneto transient analyses. Because of the different physical transient‐time constants, the steady‐state AC analysis coupled with transient thermal should be used.

The permanent magnets in the steady‐state AC analysis coupled with the transient thermal analysis can be simulated by coils with an imposed current of a frequency depending on the number of pole pairs and rotation speed. Using any of the electrically conductive materials for the axial‐flux inner slotless stator permanent‐magnet machine housing should be avoided.

The leakage flux induced by permanent magnets and spreading into the axial‐flux permanent‐machine housing is first defined by using the magneto‐transient finite‐element analysis and further used in the steady‐state AC analysis coupled with the transient thermal analyses, all in 3D. Based on the results of these analyses, the temperature distribution in entire machine is calculated and compared with the measurement results.

Introduces papers from this area of expertise from the ISEF 1999 Proceedings. States the goal herein is one of identifying devices or systems able to provide prescribed performance. Notes that 18 papers from the Symposium are grouped in the area of automated optimal design. Describes the main challenges that condition computational electromagnetism’s future development. Concludes by itemizing the range of applications from small activators to optimization of induction heating systems in this third chapter.

Reducing eddy current losses in magnets of electrical machines can be obtained by means of several techniques. The magnet segmentation is the most popular one. It imposes the least restrictions on machine performances. This paper investigates the effectiveness of the magnet circumferential segmentation technique to reduce these undesirable losses. The full and partial magnet segmentation are both studied for a frequency range from few Hz to a dozen of kHz. To increase the efficiency of these techniques to reduce losses for any working frequency, an optimization strategy based on coupling of finite elements analysis and genetic algorithm is applied. The purpose of this paper is to define the parameters of the total and partial segmentation that can ensure the best reduction of eddy current losses.

First, a model to analyze eddy current losses is presented. Second, the effectiveness of full and partial magnet circumferential segmentation to reduce eddy loss is studied for a range of frequencies from few Hz to a dozen of kHz. To achieve these purposes a 2-D finite element model is developed under MATLAB environment. In a third step of the work, an optimization process is applied to adjust the segmentation design parameters for best reduction of eddy current losses in case of surface mounted permanent magnets synchronous machine.

In case of the skin effect operating, both full and partial magnet segmentations can lead to eddy current losses increases. Such deviations of magnet segmentation techniques can be avoided by an appropriate choice of their design parameters.

Few works are dedicated to investigate partial magnet segmentation for eddy current losses reduction. This paper studied the effectiveness and behaviour of partial segmentation for different frequency ranges. To avoid eventual anomalies related to the skin effect an optimization process based on the association of the finite elements analysis to genetic algorithm method is adopted.

This paper aims to elaborate the method and algorithm for the analysis of the influence of temperature on back electromotive force (BEMF) waveforms in a line start permanent magnet synchronous motor (LSPMSM).

The paper presents a finite element analysis of temperature influence on BEMF and back electromotive coefficient in a LSPMSM. In this paper, a two-dimensional field model of coupled electromagnetic and thermal phenomena in the LSPMSM was presented. The influence of temperature on magnetic properties of the permanent magnets as well as on electric and thermal properties of the materials has been taken into account. Simulation results have been compared to measurements. The selected results have been presented and discussed.

The simulations results are compared with measurements to confirm the adequacy of this approach to the analysis of coupled electromagnetic-thermal problems.

The paper offers appropriate author’s software for the transient and steady-state analysis of coupled electromagnetic and thermal problems in LSPMS motor.

The purpose of this paper is to propose a permanent magnet-assisted synchronous reluctance machine (PMASynRM) using ferrite magnets with the same power density as rare-earth PM synchronous motors used in Toyota Prius 2010.

A novel rotor structure with rectangular PMs is discussed with respect to the demagnetization of ferrite magnets and mechanical strength. Some electromagnetic characteristics including torque, output power, loss and efficiency are calculated by 2D finite element analysis.

The results of the analysis show that a high power density and high efficiency for PMASynRM can be achieved using ferrite magnets.

This paper proposes a novel rotor structure of PMASynRM with low-cost ferrite magnets that achieves high power density as permanent machines with rare-earth PMs.

The purpose of this paper is to provide a comparison of synchronous permanent magnet machine types for wide constant power speed range operation.

A combination of analytical models and finite element analysis is used to conduct this study.

The paper has presented a detailed comparison between various types of synchronous PM machines for applications requiring a wide speed range of constant‐power operation. Key observations include: surface permanent magnet (SPM) and interior permanent magnet (IPM) machines can both be designed to achieve wide speed ranges of constant‐power operation. SPM machines with fractional‐slot concentrated windings offer opportunities to minimize machine volume and mass because of their short winding end turns and techniques for achieving high‐slot fill factors via stator pole segmentation. High back‐emf voltage at elevated speeds is a particular issue for SPM machines, but also poses problems for IPM machine designs when tight maximum limits are applied. Magnet eddy‐current losses pose a bigger design issue for SPM machines, but design techniques can be applied to significantly reduce the magnitude of these losses. Additional calculations not included here suggest that the performance characteristics of the inverters accompanying each of the four PM machines are quite similar, despite the differences in machine pole number and electrical frequency.

The paper is targeting traction applications where a very wide speed range of constant‐power operation is required.

Results presented are intended to provide useful guidelines for engineers faced with choosing the most appropriate PM machine for high‐constant power speed ratio applications. As in most real‐world drive design exercises, the choice of PM machine type involves several trade‐offs that must be carefully evaluated for each specific application.

The paper provides a comprehensive comparison between different types of synchronous PM machines, which is very useful in determining the most suitable type for various applications.

The purpose of this paper is to present the optimal design of a low-cost interior permanent magnet (IPM) alternating current (AC) motor. It examines the influence of the permanent magnet (PM) materials, and proposes a simple and practical method of optimizing the air-gap field to achieve sinusoidal back electromotive force (EMF), and to reduce the cogging torque.

IPM AC motors with different magnet materials and various topologies are comparatively studied. Finite element method (FEM) is used to predict the performances of these designs. Material costs and manufacture costs are both taken into account. Finally, an optimized design is prototyped and tested, validating the design considerations.

In an IPM AC motor, even if the rotor outer profile is round, the air-gap field distribution can be fined, while the cogging torque can be significantly reduced, by properly shaping the stator tooth tips. Nevertheless, this technique is usually applicable to motor configurations with concentrated windings, but not to those with distributed windings.

While using ferrite magnets for PM AC motors with a kW power, interior magnets are usually inserted in V-shaped slots, and the rotor outer profile is often shaped in order to enhance the air-gap field distribution. However, such a rotor configuration usually increases the manufacture costs, and also deteriorates the consistency of mass production. Therefore, a new motor configuration with a round rotor outer profile and shaped stator tooth tips is proposed. It can not only overcome the aforementioned problems, but also improve the motor performance.

The purpose of this paper is to propose improvement of the generation capability of a claw pole alternator with DC excitation in the stator (CPAES) using analytical investigation based on a dedicated reluctant model.

The paper analyzes the effects of geometry and material transformations of the magnetic circuit on the generation capability of the CPAES as well as the reduction of claw‐claw leakage flux by inserting permanent magnets in between adjacent claws.

The generation capability could be improved considering the proposed geometry and material changes of the magnetic circuit of the CPAES. The inclusion of permanent magnets in between adjacent claws offers an increase of the alternator generation due to the reduction of the claw‐claw leakage flux.

The research should be extended by building a new prototype of the CPAES in order to compare analytical results and experimental ones.

A new concept with no brush‐ring for excitation and an improvement of the generation capability of the alternator make the CPAES an interesting candidate especially in large‐scale production applications such as the automotive industry.

The paper proposes a new alternator topology called claw pole alternator with DC excitation in the stator (CPAES) and an analytical approach to improve the generation capability of such a concept, which represents a crucial challenge in electric generation systems especially in automotive applications.