Search results

The utilisation of renewable energy sources for generating electricity and potable water is one of the most sustainable approaches in the current scenario. Therefore, the current research aims to design and develop a novel co-generation system to address the electricity and potable water needs of rural areas.

The cogeneration system mainly consists of a solar parabolic dish concentrator (SPDC) system with a concentrated photo-voltaic module at the receiver for electricity generation. It is further integrated with a low-temperature thermal desalination (LTTD) system for generating potable water. Also, a novel corn cob filtration system is introduced for the pre-treatment to reduce the salt content in seawater before circulating it into the receiver of the SPDC system. The designed novel co-generation system has been numerically and experimentally tested to analyse the performance at Karaikal, U.T. of Puducherry, India.

Because of the pre-treatment with a corn cob, the scale formation in the pipes of the SPDC system is significantly reduced, which enhances the efficiency of the system. It is observed that the conductivity, pH and TDS of seawater are reduced significantly after the pre-treatment by the corncob filtration system. Also, the integrated system is capable of generating 6–8 litres of potable water per day.

The integration of the corncob filtration system reduced the scaling formation compared to the general circulation of water in the hoses. Also, the integrated SPDC and LTTD systems are comparatively economical to generate higher yields of clean water than solar stills.

One of the existing and commonly used solar energy harvesting devices is the parabolic trough solar collector (PTSC). Because of their ability to operate in low and medium temperatures, parabolic trough concentrators are widely used in power generation plants and industrial process heating applications. Therefore, the investigation of how different operating conditions affect these devices’ overall efficiency has received a great deal of attention in the recent decade. This study aims to enhance the thermal performance of the PTSC and reduce the system cost.

In the novel configuration, a noncirculated nanofluid absorbs solar radiation through a glass wall. The base fluid was synthetic oil (5W30), and the nanoparticles used were copper oxide. The heat captured is immediately absorbed by the water circulating inside the copper tube immersed in the nanofluid. ANSYS FLUENT 15.0 was used for carrying out computational fluid dynamics simulations for two models of single and triple copper tubes. The experimental results obtained from a test rig constructed for this purpose were compared with the numerical outcomes of the single copper tube model.

The findings of the simulation demonstrated that performance was superior for the single copper tube model over the triple copper tube model. The numerical findings of the single copper tube model were compared with the experimental results. The numerical and experimental results differed from 3.17% to 5.6%. Investigations were carried out to study the effects of varying the volumetric flow rate of (20, 40, 60 and 80 L/h) and water inlet temperatures of (300, 315 and 330 K) on the effectiveness and performance of the newly developed model. Additionally, two nanofluid volume fractions of 0.05% and 0.075% were used for investigating their effect on the performance of the novel configuration. According to the findings, the highest thermal efficiency of 55.31% was recorded at 0.075% concentration and 80 L/h volume flow rate.

In this study, a novel direct absorption solar collector configuration using a noncirculated nanofluid was designed to enhance the thermal efficiency of PTSC. This new approach makes it possible to boost the thermal performance of the PTSC and lower the system’s cost.

In the context of fixed-wing aircraft wing assembly, there is a need for a rapid and precise measurement technique to determine the center distance between two double-hole components. This paper aims to propose an optical-based spatial point distance measurement technique using the spatial triangulation method. The purpose of this paper is to design a specialized measurement system, specifically a spherically mounted retroreflector nest (SMR nest), equipped with two laser displacement sensors and a rotary encoder as the core to achieve accurate distance measurements between the double holes.

To develop an efficient and accurate measurement system, the paper uses a combination of laser displacement sensors and a rotary encoder within the SMR nest. The system is designed, implemented and tested to meet the requirements of precise distance measurement. Software and hardware components have been developed and integrated for validation.

The optical-based distance measurement system achieves high precision at 0.04 mm and repeatability at 0.02 mm within a range of 412.084 mm to 1,590.591 mm. These results validate its suitability for efficient assembly processes, eliminating repetitive errors in aircraft wing assembly.

This paper proposes an optical-based spatial point distance measurement technique, as well as a unique design of a SMR nest and the introduction of two novel calibration techniques, all of which are validated by the developed software and hardware platform.

In this investigation, a linear encoder system based on the ultrasonic transducer has been proposed. Ultrasonic transducers are usually designed for distance measurements, such as the time of flight method and sonar system. These applications are defined as discrete-length measurement technologies. The purpose of this study is to develop a continuous displacement measurement system using ultrasonic transducers.

A modified signal processing based on heterodyne signaling is implemented in this system. In the proposed signal processing, there is an automatic gain control module, a phase-shifting module, a phase detection module, an interpolation module and especially a frequency multiplication module, which can enhance the resolution and reduce the interpolation error simultaneously.

The proposed system can generate the encoding signals and is compatible with most motion control systems. For the experimental result, the maximum measurement error and standard deviation are about −0.027 and 0.048 mm, respectively. It shows that the proposed encoder system has the potential for displacement measurement tasks.

This study reveals an ultrasonic linear encoder that is capable of generating an incremental encoding signal, accompanied by a corresponding signal processing methodology. In contrast to the conventional heterodyne signal processing approach, the proposed multiplication method effectively reduces the interpolation error that arises because of multiple reflections.

With the development of artificial intelligence, proximity sensors show their great potential in intelligent perception. This paper aims to propose a new planar capacitive sensor for the proximity sensing of a conductor.

Different from traditional structures, the proposed sensor is characterized by sawtooth-structured electrodes. A series of numerical simulations have been carried out to study the impact of different geometrical parameters such as the width of the main trunk, the width of the sawtooth and the number of sawtooths. In addition, the impact of the lateral offset of the approaching graphite block is investigated.

It is found that sensitivity is improved with the increase of the main trunk with, sawtooth width and sawtooth number while a larger lateral offset leads to a decrease in sensitivity. The performance of the proposed planar capacitive proximity sensor is also compared with two conventional planar capacitive sensors. The results show that the proposed planar capacitive sensor is obviously more sensitive than the two conventional planar capacitive sensors.

In this paper, a new planar capacitive sensor is proposed for the proximity sensing of a conductor. The results show that the capacitive sensor with the novel structure is obviously more sensitive than the traditional structures in the detection of the proximity conductor.

The purpose of this study is to demonstrate and characterise a soft-tooled micro-injection moulding process through in-line measurements and surface metrology using a data-intensive approach.

A soft tool for a demonstrator product that mimics the main features of miniature components in medical devices and microsystem components has been designed and fabricated using material jetting technique. The soft tool was then integrated into a mould assembly on the micro-injection moulding machine, and mouldings were made. Sensor and data acquisition devices including thermal imaging and injection pressure sensing have been set up to collect data for each of the prototypes. Off-line dimensional characterisation of the parts and the soft tool have also been carried out to quantify the prototype quality and dimensional changes on the soft tool after the manufacturing cycles.

The data collection and analysis methods presented here enable the evaluation of the quality of the moulded parts in real-time from in-line measurements. Importantly, it is demonstrated that soft-tool surface temperature difference values can be used as reliable indicators for moulding quality. Reduction in the total volume of the soft-tool moulding cavity was detected and quantified up to 100 cycles. Data collected from in-line monitoring was also used for filling assessment of the soft-tool moulding cavity, providing about 90% accuracy in filling prediction with relatively modest sensors and monitoring technologies.

This work presents a data-intensive approach for the characterisation of soft-tooled micro-injection moulding processes for the first time. The overall results of this study show that the product-focussed data-rich approach presented here proved to be an essential and useful way of exploiting additive manufacturing technologies for soft-tooled rapid prototyping and new product introduction.

This paper aims to analyze energy and exergy analysis of solar-based intercooled and reheated gas turbine (GT) trigeneration cycle using parabolic trough solar collectors (PTC) with the use of MATLAB 2018.

In the first section of this paper, the solar-based GT is validated with the reference paper. According to the reference paper, the solar field is comprising 30 modules in series and 35 modules in parallel series, where a total of 1,050 modules of PTC are taken into consideration. In the second part of this paper, the hybridization of the solar, GT trigeneration cycle is analyzed and optimized. In the last section of this paper, the hybridization of solar, intercooled and reheated GT trigeneration systems is examined and compared.

The results examined the first section, the power produced by the cycle will be 37.34 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and the efficiencies of energy and exergy will be 38.34% and 39.76%, respectively. The results examined in the second section, the power produced by the cycle will be 38.4 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and accordingly the efficiency of energy and exergy is found to be 40.011% and 41.763%. Where in the last section, the power produced by the cycle will be 41.43 MW at 0.5270 kg/s mass flow rate of the natural gas consumption and the energy and exergy efficiencies will be 39.76% and 40.924%, respectively.

The author confirms that this study is original and has neither been published elsewhere nor it is currently under consideration for publication elsewhere.

Cross-layer approach in media access control (MAC) layer will address interference and jamming problems. Hybrid distributed MAC can be used for simultaneous voice, data transmissions in wireless sensor network (WSN) and Internet of Things (IoT) applications. Choosing the correct objective function in Nash equilibrium for game theory will address fairness index and resource allocation to the nodes. Game theory optimization for distributed may increase the network performance. The purpose of this study is to survey the various operations that can be carried out using distributive and adaptive MAC protocol. Hill climbing distributed MAC does not need a central coordination system and location-based transmission with neighbor awareness reduces transmission power.

Distributed MAC in wireless networks is used to address the challenges like network lifetime, reduced energy consumption and for improving delay performance. In this paper, a survey is made on various cooperative communications in MAC protocols, optimization techniques used to improve MAC performance in various applications and mathematical approaches involved in game theory optimization for MAC protocol.

Spatial reuse of channel improved by 3%–29%, and multichannel improves throughput by 8% using distributed MAC protocol. Nash equilibrium is found to perform well, which focuses on energy utility in the network by individual players. Fuzzy logic improves channel selection by 17% and secondary users’ involvement by 8%. Cross-layer approach in MAC layer will address interference and jamming problems. Hybrid distributed MAC can be used for simultaneous voice, data transmissions in WSN and IoT applications. Cross-layer and cooperative communication give energy savings of 27% and reduces hop distance by 4.7%. Choosing the correct objective function in Nash equilibrium for game theory will address fairness index and resource allocation to the nodes.

Other optimization techniques can be applied for WSN to analyze the performance.

Game theory optimization for distributed may increase the network performance. Optimal cuckoo search improves throughput by 90% and reduces delay by 91%. Stochastic approaches detect 80% attacks even in 90% malicious nodes.

Channel allocations in centralized or static manner must be based on traffic demands whether dynamic traffic or fluctuated traffic. Usage of multimedia devices also increased which in turn increased the demand for high throughput. Cochannel interference keep on changing or mitigations occur which can be handled by proper resource allocations. Network survival is by efficient usage of valid patis in the network by avoiding transmission failures and time slots’ effective usage.

Literature survey is carried out to find the methods which give better performance.

The purpose of this paper is to ensure the anonymity and security of health data and improve the integrity and authenticity among patients, doctors and insurance providers. Simulation and validation algorithms are proposed in this work to ensure the proper implementation of the distributed system to secure and manage healthcare data. The author also aims to examine the methodology of Wireless Body Area Networks and how it contributes to the health monitoring system.

Wireless Body Area Network (WBAN) plays an important role in patient health data monitoring. In this paper, a novel framework is designed and proposed to generate data by the sensor machines and be stored in the cloud, and the transactions can be secured by blockchain. DNA cryptography is used in the framework to encrypt the hashes of the blocks. The proposed framework will ensure the anonymity and security of the health data and improve the integrity and authenticity among the patients, doctors and insurance providers.

Cloud Computing and Distributed Networking have transformed the IT industry and their amalgamation with intelligent systems would revolutionize the Healthcare Industry. The data being generated by devices is huge and storing it in the cloud environment would be a better decision. However, the privacy and security of healthcare data are still a concern because medical data is very confidential and desires to be safe and secure. The blockchain is a promising distributed network that ensures the security aspect of the data and makes the transactions authentic and transparent. In this work, the data is collected using various sensor devices and is transmitted to the cloud through the WBAN via the blockchain network.

In this paper, a framework for securing and managing the healthcare data generated by intelligent systems is proposed. As the data generated by these devices are heterogeneous and huge in nature, the cloud environment is chosen for its storage and analysis. Therefore, the transactions to and from the cloud are secured by using the blockchain-based distributed network.

The target end-users of our system are the patients to keep themselves informed and healthy, healthcare providers to monitor the conditions of their patients virtually, and the health insurance providers to have a track of the history of the patients, so that no fraudulent claims can be made.

The target end-users of our system are the patients for keeping themselves informed and healthy, healthcare providers for monitoring the conditions of their patients virtually and the health insurance providers to have a track of the history of the patients, so that no fraudulent claims can be made.

Before designing a navigation system, it is necessary to analyse possible approaches in terms of expected accuracy, existing limitations and economic justification to select the most advantageous solution. This paper aims to collect possible navigation methods that can provide correction for inertial navigation and to evaluate their suitability for use on a manoeuvring tactical missile.

The review of existing munitions was based on data collected from the literature and online databases. The data collected included dimensions, performance, applied navigation and guidance methods and their achievable accuracy. The requirements and limitations identified were confronted with the range of sensor parameters available on the market. Based on recent literature, navigation methods were reviewed and evaluated for applicability to inertial navigation system (INS) correction in global navigation satellite system-denied space.

The performance analysis of existing munition shows that small and relatively inexpensive micro-electro-mechanical system-type inertial sensors are required. A review of the parameters of existing devices of this type has shown that they are subject to measurement errors that do not allow them to achieve the delivery accuracy expected of precision missiles. The most promising navigation correction methods for manoeuvring flying objects have been identified.

The information presented in this paper is the result of the first phase of a project and presents the results of the requirements selection, initial sizing and preliminary design of the navigation system. This paper combines a review of the current state of the art in missile systems and an analysis of INS accuracy including the selection of sensor parameters.