Search results

The purpose of this study was to overcome discomfort associated with it, a resin finish was applied in conjunction with hydrophilic polyurethane.

The process variables included concentrations of polyurethane and resin finishes, and pH under central composite design (CCD). The fabric specimens were assessed for crease recovery angle (CRA), tensile strength and moisture management properties.

Some models were developed for prediction of CRA and overall moisture management capability (OMMC) of treated fabric. It was observed that polyurethane concentration showed a parabolic relationship with CRA and a direct relationship with OMMC, whereas resin concentration showed a parabolic relationship with CRA and an inverse relationship with OMMC. Increase in pH from acidic to alkaline resulted in a decrease in CRA but an increase in OMMC. The untreated specimen had the highest tensile strength, whereas the specimen treated with polyurethane showed the least tensile strength loss, and the one treated with resin showed the highest loss in tensile strength.

As the polyurethane-based finish is soft and hydrophilic, so it was expected that it would overcome the uncomfortable feature of durable press finish, and with its flexibility, the strength losses might reduce.

This is the first report about the investigation of effects of increasing flexibility of the cross-link by incorporating polyurethane compounds into a typical dimethylol dihydroxy ethylene urea durable press resin formulation.

This paper aims to develop bilayer woven fabrics with different picking sequences with enhanced comfort without any change in the constituent materials.

Six bilayer woven fabrics were produced on Dobby loom with 3/1 twill weave using micro-polyester yarn. Three different picking sequences, i.e. single pick insertion (SPI), double pick insertion (DPI) and three pick insertion (3PI), were used in both face and back layers. The effect of picking sequence on air permeability (AP), volume porosity, thermal resistance and overall moisture management capability (OMMC) of the samples were analyzed.

The results showed that 3PI–3PI picking sequence gives the highest OMMC, AP and thermal resistance in bilayer woven fabrics and the least results exhibited by SPI–SPI picking sequence.

This research uses a bilayer woven system that develops channels and trapes the air causing higher thermal resistance; therefore, applicable for winter sports clothing rather than for summer wear. Developed bilayer woven fabrics can be used in winter sportswear to improve the comfort of the wearer and reduce fatigue during activity.

Authors have developed bilayer fabrics by changing the picking sequences, i.e. SPI, DPI and 3PI of weft yarns in both layers and compared their thermo-physiological comfort properties.

Clothing must also assist the body’s thermal control function under changing physical loads in such a way that the body’s thermal and moisture management is balanced, and a microclimate is created next to the skin. One of the factors which affect moisture transport in a fabric is a fibre type. Hence, the purpose of this paper is to blend the natural hollow and low density fibre, milkweed, with cotton fibre at different proportions and to analyse and compare the influence of milkweed blend proportion on moisture management properties of rotor yarn fabrics with 100 per cent cotton fabric.

In the present study, cotton/milkweed blended rotor yarns were produced by using S-4 cotton variety and milkweed fibres in three different blend proportions such as cotton/milkweed 80/20, 60/40 and 40/60 along with 100 per cent cotton yarn with yarn count of 20 Ne. The single jersey knitted fabrics were produced with similar constructional parameters and then the fabrics were then scoured, bleached and neutralised as per the standard procedure. The fabrics have been analysed for its various moisture management properties using moisture management tester (MMT) and are statistically analysed.

The results indicate that, all the C/M blended fabrics have been classified as “moisture management fabric” and 100 per cent cotton fabric has been classified as “Fast absorbing and Quick Drying Fabric”. The overall moisture management capacity of C/M 40/60 fabric is excellent and could be used for summer, active and summer wear applications. One-way ANOVA analysis carried out at 95 per cent confidence level showed that the results are statistically significant. The pair-wise strength and association between various moisture management indices was analysed using Pearson correlation coefficient and observed that OWTC and OMMC was found to be positively and linearly related to each other.

The authors are confident that the cotton/milkweed blended yarns can be used as an inner wear and sportswear applications owing to the higher moisture regain and hollowness of milkweed fibre combined with the low packing density of C/M blended yarns which leads to overall improvement in moisture management properties of fabrics.

The paper aims to improve the protective and comfort properties of both woven and knitted acrylic fabrics by applying a hybrid waterborne polyurethane/fluorocarbon hydrophobic finish.

In this study, it was found that the transportation of water from fabrics is one of the important textile parameters. To improve this property, a polyurethane-based finish (Dicrylan BSRN^®) and an oil- and water-repellent finish (Oleophobol ZSR^®) were applied by using the pad-dry-cure method. After applying the finishes, the resultant fabric samples were investigated for various textile properties.

The application of Oleophobol ZSR^® increased the absorbency time, indicating that the fabric became hydrophobic, whereas the application of Dicrylan BSRN^® finish improved the moisture management properties of the woven acrylic. The tensile strength of the woven acrylic fabric was not significantly affected by the application of these finishes. The contact angle of treated knitted fabrics increased and air permeability decreased with an increase in the concentration of Oleophobol ZSR^®.

Moisture management is one of the crucial performance criteria in today’s apparel industry. Therefore, fluorochemicals are one of the major precursors used in water-repellent finishes and waterproof membranes in outdoor garments. Based on this fact, this research work focused on the textile sector, where moisture management is required.

This is the first report about the combined application of waterborne polyurethane and fluorochemical-based finishes on acrylic fabrics to tune their comfort and hydrophobic properties.

The purpose of this paper is to investigate effect of material properties in 3D knitted fabrics on thermo-physiological comfort.

In the present study six different spacer fabrics were developed. Among these six fabrics, it was classified into two groups for convenient analysis of results, the first group has been developed using polyester/polypropylene blend with three different proportion and second group with polyester/polypropylene/lycra blend having another three different composition. As a spacer yarn, three different types of 88 dtex polyester monofilament yarn and polyester multifilament yarns (167 dtex and 14.5 tex) were used and 14.5 tex polypropylene and 44 dtex lycra multifilament yarns were also used for the face and back side of the spacer fabrics (Table I). These fabrics were developed in Syntax Pvt Ltd Czech Republic.

The main influence on the water vapour permeability of warp knitted spacer fabrics is the kind of raw material, i.e. fibre wetting and wicking. Also there is no correlation between air permeability and water vapour permeability. It is found that both air permeability and thermal conductivity are closely related to the fabric density. It is also found that the fabric characteristics of spacer fabric show a very significant effect on the air permeability, thermal conductivity and mechanical properties of spacer fabric. Therefore, selection of spacer fabric for winter clothing according to its fabric characteristics.

The main objective of the present study is to produce spacer knitted 3D fabrics suitable for defined climatic conditions to be used as clothing or in sports goods.

New 3D knitted spacer fabrics can be produced with improved comfort properties.

The essential properties of active sports fabrics are moisture management, quick-drying, body heat management and thermal regulations. Fibre type, blending nature, yarn and fabric structure and the finishing treatment are the key parameters that influenced the performance of the clothing meant for sportswear. This study aims to investigate the effect of fibre blending and structural tightness factors on bi-layer sport fabric's dimensional, moisture management and thermal properties.

In this study, 12 different bi-layer inter-lock fabrics were produced. Polyester filament (120 Denier) yarn was fed to form the backside of the fabric, and the face side was varied with cotton, modal, wool and soya spun yarns of 30sNe. Three different types of structural tightness factors were considered, such as low, medium and high were taken for sample development. The assessment towards dimensional, moisture management and thermal properties was carried out on all the samples.

The polyester-modal blend with a high tightness factor has shown maximum overall moisture management capability (OMMC) values of 0.73 and air permeability of 205.3 cm³/cm²/s. The same sample has shown comparatively higher thermal conductivity of 61.72 × 10^–3 W m^-1 °C^-1(Under compression state) and 58.45 × 10^–3 W m^-1 °C^-1 (under recovery state). In the case of surface roughness is concerned, polyester-modal blends have shown the lowest surface roughness, surface roughness amplitude and surface friction co-efficient. Among the selected fibre combinations, the overall comfort level of polyester-modal bi-layer knitted structure with a higher tightness factor is appreciable. Polyester-modal is more suitable for active sportswear among the four fiber blend combinations.

The outcome of this study will help to gain a better understanding of fibre blends, structural tightness factor and other process specifications for the development of bi-layer fabric for active sportswear applications. The dynamic functional testing methods (Moisture management and Thermal properties) were carried out to simulate the actual wearing environment of the sports clothing. This study will create a new scope of research opportunities in the field of bi-layer sports textiles.

This study was conducted to explore the influence of fibre blend and structural tightness factor on the comfort level of sportswear and to find the suitable fibre blend for active sportswear clothing.

Eri is a short-stapled fibre that possesses an excellent soft feel and warmness to the wearer. Investigation of thermal comfort and moisture properties of Eri silk fabric provides the enhanced commercial scope for Eri silk-based clothing.

To examine the impact of process factors on thermal and moisture properties, three different single knit Eri silk structures were made, each with a different loop length and yarn count. Three different linear densities of Eri silk spun yarn (15, 20 and 25 tex) were selected. Three distinct knitted constructions, including plain jersey, popcorn and cellular blister, were created, along with two different loop lengths.

The novel cellular blister structure has shown appreciable thermal comfort properties than the other two structures. Yarn fineness and loop length were significant with most of the thermal comfort properties.

In recent times the Eri silk production is completely domesticated, so the new demand can easily be met by the producers. This research will create a new scope for Eri silk fibres in sportswear and leisure wear.

This study was conducted to explore the influence of knit structure, loop length and yarn count on the thermal comfort properties of the clothing.

The purpose of this work is to investigate the effect of filament composition with different specifications on the thermal comfort properties of bi-layer knitted fabrics.

In this paper eight bi-layer knitted fabrics with the same knitting structure but different filament compositions were prepared, and the thermal-wet comfort properties of these fabrics were examined. According to experimental data, the effect of filament composition on the thermal comfort properties of fabric was analyzed.

The increasing difference of hydrophilicity between inner and outer layers resulted in the enhancement of moisture management properties. Better thermal-physiology performance was exhibited by fabrics made up of finer and circular section fibers. Excellent thermal transfer, drying performance and one-way water transport capacity benefited the improvement of dynamic cooling effect of fabrics.

This work provides a useful and effective method for the development of bi-layer knitted fabric applied for sports and summer clothing.

The purpose of this paper is to explore the synergic effect of wild turmeric (Curcuma Aromatica Salisb.) and holy basil (Ocimum Tenuiflorum L.) combination herbal extracts treatment on the moisture management properties of cotton, lyocell and micro-denier single jersey knitted fabrics and the factors affecting it, which is intended for the development of healthcare apparel products.

The pre-treated single jersey knitted fabrics of cotton, lyocell and micro-denier polyester fabrics were given finishing treatment with the wild turmeric (Curcuma Aromatica Salisb.) and holy basil (Ocimum Tenuiflorum L.) combination herbal extract proportions of 100%:0%, 75%:25%,50%:50%; 25%:75% and 0%:100%. The D-optimal factorial design developed using Design Expert software was used for the study. The finishing treatments were carried out using the pad−dry−cure method. The aim of the work is to find out the influence of combination herbal extract proportion, textile material and their interaction effect on the moisture management properties.

The ANOVA results revealed that the overall moisture management properties of single jersey knitted fabrics are influenced by the material type, combination herbal extract proportion and the interaction between material type and the combination herbal extracts proportion. The overall moisture management properties of combination herbal extracts treated cotton single jersey fabrics are found to be better than that of lyocell and micro-denier polyester fabrics due to their excellent accumulative one-way transport capability after the finishing treatment. Among the combination herbal extract proportions, 50:50 per cent combination herbal extract proportion was found to be better than other proportions.

The study on the moisture management properties of combination herbal extracts of wild turmeric (Curcuma Aromatica Salisb.) and holy basil (Ocimum Tenuiflorum L.) is a novel attempt to explore the synergic effect of active constituents in both the herbs.

The purpose of this paper is to investigate thermal comfort performances of socks produced from cotton and regenerated cellulosic fiber yarns by thermal resistance (by a newly designed foot thermal manikin), moisture management tester (MMT) parameters and permeability (air and water vapor) tests.

Single jersey fabrics and socks were knitted from 30 Ne yarns produced from cotton, different regenerated cellulosic fibers (viscose, modal, bamboo, micromodal, Tencel®, Tencel LF®) and their blends. Thermal resistances of the socks were compared by a newly developed thermal foot manikin in a more realistic way than measurements in fabric form. Besides air and water vapor permeability, moisture management parameters of the fabrics were tested to differentiate performances of cellulosic fibers.

Results show that air permeability, liquid absorption and transfer parameters measured by MMT are generally identical and better for regenerated cellulosic fabrics than cotton. Micromodal and Tencel® have better performances for liquid transfer and overall moisture management capacities are superior for bamboo and Tencel LF®. Thermal resistances of the socks are minimum for Tencel LF® having a cross-linked structure and maximum for viscose socks.

It is thought that thermal resistance measured in socks form is more realistic than fabric measurements and results of this study that can be valid for all knitted garments. Moreover, comprehensive material plan of the study is valuable for getting reliable results for regenerated cellulosic fibers that have small differences in cases of thermal resistance and liquid transfer.