Search results

The different performance tests were conducted on diesel engine compression ignition (CI) mode and CRDi engine.

The CI engine was suitably modified to CRDi engine with Toroidal re-entrant combustion chamber (TRCC) and was run in dual-fuel (DF) mode. Hydrogen (H₂) was supplied at different flow rates during the suction stroke, and 0.22 Kg/h of hydrogen fuel flow rate (HFFR) was found to be optimum. Diesel and biodiesel were used as pilot fuels. The CRDi engine with DF mode was run at various injection pressures, and 900 bar was found to be optimum injection pressure (IP) with 10o before top dead center (bTDC) as fuel injection timing (IT).

These operating engine conditions increased formation of oxides of nitrogen (NOx), which were reduced by exhaust gas recycle (EGR). With EGR of 15%, CRDi engine resulted in 12.6% lower brake thermal efficiency (BTE), 5.5% lower hydrocarbon (HC), 7.7% lower carbon monoxide (CO), 26% lower NOx at 80% load as compared to the unmodified diesel engine (CI mode).

The current research is an effort to study and evaluate the performance of CRDi engine in DF mode with diesel-H₂ and BCPO-H₂ fuel combinations with TRCC.

In the cylinders of a marine diesel engine, self-ignition occurs in a very short time after the fuel injection into the combustion chamber. Therefore, this paper aims to develop a model of diesel fuel spray for the early stage of fuel spray in the marine diesel engine. The main technical aspects such as nozzle diameter of the marine engine injector and backpressure in the combustion chamber were taken into consideration.

In this paper, laboratory experimental studies were carried out to determine parameters of fuel spray in an early stage of injection in the marine diesel engine. The optical measuring Mie scattering technique was used to record the fuel injection process. The working space was a constant volume chamber. The backpressure parameters in the constant volume chamber were the same as during the operation of the marine diesel engine. Based on the experimental studies and important Hiroyasu and Arai models of fuel spray presented in literature was proposed new model of fuel spray parameters for marine diesel injectors.

In this paper, the proposed new model of the two main parameters described fuel spray evolution”: new model of spray tip penetration (STP) and spray cone angle (SCA). New model propagation of fuel STP in time was included the influence of nozzle diameter and backpressure. The proposed model has a lower error, about 15%–34%, than the model of Hiroyasu and Arai. Moreover, a new model of the evolution over time of the SCA is developed.

In the future research of fuel spray process must be taken influence of the fuel temperature. Diesel fuel has a different density and viscosity in dependence of fuel temperature. Therefore are predicted of the expansion about influence of fuel temperature, new model of fuel spray for a marine diesel engine. The main limitations occurring in the research are not possible to carry out the research while real operation marine diesel engine.

An experimental test was carried out for a real fuel injector of a marine diesel engine. Design parameters and fuel injection parameters were selected on the basis of the actual one. In the literature, SCA is defined as a constant parameter for the specific preliminary data. A new model for the early stage of fuel spray of SCA propagation in time has been proposed. The early stage of fuel spray is especially important, because in this time comes in there to fuel self-ignition.

The purpose of this paper is to analyze and compare the performances of novel roadable personal air vehicle (PAV) concepts that meet established operational requirements with different types of engines.

The vehicle configuration was devised considering the dimensions and operational restrictions of the roads, runways and parking lots in South Korea. A folding wing design was adopted for road operations and parking. The propulsion designs considered herein use gasoline, diesel and hybrid architectures for longer-range missions. The sizing point of the roadable PAV that minimizes the wing area was selected, and the rate of climb, ground roll distance, cruise speed and service ceiling requirements were met. For various engine types and mission profiles, the performances of differently sized PAVs were compared with respect to the MTOW, wing area, wing span, thrust-to-weight ratio, wing loading, power-to-weight ratio, brake horsepower and fuel efficiency.

Unlike automobiles, the weight penalty of the hybrid system because of the additional electrical components reduced the fuel efficiency considerably. When the four engine types were compared, matching the total engine system weight, the internal combustion (IC) engine PAVs had better fuel efficiency rates than the hybrid powered PAVs. Finally, a gasoline-powered PAV configuration was selected as the final design because it had the lowest MTOW, despite its slightly worse fuel efficiency compared to that of the diesel-powered engine.

Although an electric aircraft powered only by batteries most capitalizes on the operating cost, noise and emissions benefits of electric propulsion, it also is most hampered by range limitations. Air traffic integration or any safety, and noise issues were not accounted in this study.

Aircraft sizing is a critical aspect of a system-level study because it is a prerequisite for most design and analysis activities, including those related to the internal layout as well as cost and system effectiveness analyses. The results of this study can be implemented to design a PAV.

This study can contribute to the establishment of innovative PAV concepts that can alleviate today’s transportation problems.

This study compared the sizing results of PAVs with hybrid engines with those having IC engines.

This study aims to explore how corporate discourses enact legitimation strategies aimed at repairing pragmatic, moral and cognitive legitimacy types (Suchman, 1995) after a scandal involving sustainability, namely, the Volkswagen’s 2015 diesel scandal.

By drawing on the discursive nature of legitimacy, this study conducts a critical discourse analysis to identify how the scandal is depicted and which semantic, grammatical and lexical features characterise discourses. It then relates discourses and their features to legitimation strategies that help repair diverse types of legitimacy.

To repair pragmatic legitimacy, discourses on a few actors and processes enact strategies of creating monitors and avoiding panic. Such discourses include grammatical features only. Discourses on the event, actors, processes and topics of apology, trust and integrity aim to repair moral legitimacy. Enriched with grammatical and lexical features, they mobilise disassociation, excuse, justify and restructure strategies. Discourses on the event, actors, processes and topics of corporate qualities, history and future strategy help repair cognitive legitimacy by enacting an avoiding panic strategy. Grammatical, lexical and semantic features characterise such discourses.

The study reveals the potentials of critical discourse analysis to bring out from texts practical modes of communicating, and specifically those discourses and features of discourses that serve legitimacy purposes.

This study offers insights into the connection among discourses, relegitimation strategies and legitimacy types by combining the discursive nature of legitimacy with critical discourse analysis. It also contributes to the growing literature on how organisations face the legitimacy challenges raised by scandals involving sustainability.

The purpose of this paper is to investigate how technology-forcing regulations affect the product development process in the supply chain of heavyweight vehicles.

Through a case study, this paper seeks to understand how one of the leading companies in heavyweight vehicles manufacturing industry and its engine supplier in Brazil introduce eco-design practices into its engine development process.

Through case studies conducted in a heavyweight vehicle producer and its engine supplier, this study shows that, in addition to meeting the standards and legislation, the automaker uses ecodesign practices during the product development cycle such as a design that eliminates harmful and hazardous materials and a project that allows recycling, the reuse of parts and energy efficiency, thereby reducing the environmental impact. However, without the mandatory requirements imposed by federal legislation, products with lower environmental impacts would rarely be developed, as environmental performance is not demanded by customers, who are mainly cost driven. Technology-forcing regulations play an important role in enhancing the adoption of ecodesign practices, but market and competitive conditions also play an important role.

Several studies on the impacts of public policies and development for the automobile sector have been conducted, but there is a lack of studies in the area of commercial vehicles, especially in Brazil. Therefore, this research is justified by new demands of society, in addition to the necessity of complying with legal requirements and the adoption of good practices related to eco-design.

Purpose – This work aims to study the treatment of adsorbant on the increasing liquid hydrocarbon quality produced by pyrolysis low density polyethylene (LDPE) plastic waste at low temperature. The hydrocarbon distribution, physicochemical properties and emission test were also studied due to its application in internal combustion engine. This research uses pure Calcium carbonate (CaCO₃) and pure activated carbon as adsorbant, LDPE type clear plastic samples with control variable that is solar gas station.

Design/Methodology/Approach – LDPE plastic waste of 10 kg were vaporized in the thermal cracking batch reactor using LPG 12 kg as fuel at range temperature from 100 to 300°C and condensed into liquid hydrocarbon. Furthermore, this product was treated with the mixed CaCO₃ and activated carbon as adsorbants to decrease contaminant material.

Findings – GC-MS identified the presence of carbon chain in the range of C6–C44 with 24.24% of hydrocarbon compounds in the liquid. They are similar to diesel (C6–C14). The 30% of liquid yields were found at operating temperature of 300°C. The calorific value of liquid was 46.021 MJ/Kg. This value was 5.07% higher than diesel as control.

Originality/Value – Hydrocarbon compounds in liquid produced by thermal cracking at a low temperature was similar to liquid from a catalytic process.

This paper analyzes two external costs often associated with port development, cost to fisheries from marine dredge disposal and damages from air pollution, using estimates of development and operation for a proposed (but since cancelled) container port as a case study. For dredge disposal, a bio-economic model was used to assess short- and long-term and indirect (joodweb) damages to fisheries from marine disposal of clean sediments. In the case of air pollution, estimates of annual activity levels and emission coefficients are used to estimate incremental annual emissions of three key pollutants (NOx, HC and CO) for trucks, trains, yard vehicles, and vessels. These estimates allow for phasing in of strict new air pollution regulations. For both external costs, sensitivity analyses are used to reflect uncertainty. Estimates of shadow values in year 2002 dollars amount from $0.094 per cubic yard to $0.169 per cubic yard of clean dredged material for the selected disposal site and from $0.0584 per mile (jor current control standards) to $ 0. 0023 per mile (after phasing in of new regulations) for air pollution from heavy trucks.

Shipping is a major source of air pollution, causing severe impacts on the environment and human health, greatly contributing to the creation of greenhouse gases and influencing climate change. The research was investigated to provide a better insight into the emission inventories in the Red River in Hanoi (Vietnam) that is often heavily occupied as the primary route for inner-city waterway traffic.

The total emissions of seven different pollutants (PM₁₀, PM_2.5, SO_x, CO, CO₂, NO_x and HC) were estimated using the SPD-GIZ emission calculation model.

The results show that CO₂ has the most significant contribution to the gas volume emitted: 103.21 tons/day. Remarkably, bulk carriers are the largest emission vehicle, accounting for more than 97% of total emissions, due to their superior number and large capacity.

The result to have a roadmap for making efforts to fulfil its commitment so that it could achieve its net-zero climate target by 2050 in Vietnam as committed at COP26.

In this research, the number of vehicles and types of vessels travelling on the Red River flowing within Hanoi territory and other activity data are reported. The tally data will be used to estimate emissions of seven different pollutants (PM₁₀, PM_2.5, SO_x, CO, CO₂, NO_x and HC) using a method combining both top-down and bottom-up approaches.

This paper aims to investigate the wear behaviour of different materials for cylinder liners and piston rings in a linear reciprocating tribometer with special focus on the wear of the cylinder liner in the boundary lubrication regime.

Conventional nitrided steel, as well as diamond-like carbon and chromium nitride-coated piston rings, were tested against cast iron, AlSi and Fe-coated AlSi cylinder liners. The experiments were carried out with samples produced from original engine parts to have the original surface topography available. Radioactive tracer isotopes were used to measure cylinder liner wear continuously, enabling separation of running-in and steady-state wear.

A ranking of the material pairings with respect to wear behaviour of the cylinder liner was found. Post-test inspection of the cylinder samples by scanning electron microscopy (SEM) revealed differences in the wear mechanisms for the different material combinations. The results show that the running-in and steady-state wear of the liners can be reduced by choosing the appropriate material for the piston ring.

The use of original engine parts in a closely controlled tribometer environment under realistic loading conditions, in conjunction with continuous and highly sensitive wear measurement methods and a detailed SEM analysis of the wear mechanisms, forms an intermediate step between engine testing and laboratory environment testing.

This paper aims to present the main results achieved in the frame of the TIVANO national-funded project which may anticipate, in a stepped approach, the evolution and the design of the enabling technologies needed for a hybrid/electric medium altitude long endurance (MALE) unmanned aerial vehicle (UAV) to perform persistent intelligence surveillance reconnaissance (ISR) military operations.

Different architectures of hybrid-propulsion system are analyzed pointing out their operating modes to select the more suitable architecture for the reference aircraft. The selected architecture is further analyzed together with its electric power plant branch focusing on electric system architecture and the selected electric machine. A final comparison between the hybrid and standard propulsion is given at aircraft level.

The use of hybrid propulsion may lead to a reduction of the total aircraft mass and an increase in safety level. However, this result comes together with a reduced performance in climb phase.

This study can be used as a reference for similar studies and it provides a detailed description of propulsion operating modes, power management, electric system and machine architecture.

This study presents a novel application of hybrid propulsion focusing on a three tons class MALE UAV for ISR missions. It provides new operating modes of the propulsion system and a detailed electric architecture of its powertrain branch and machine. Some considerations on noise emissions and infra-red traceability of this propulsion, at aircraft level.