Search results

This paper aims to study the effect of corrugated skins on the aerodynamic performance of the cambered NACA 0012 airfoils at different corrugations parameters, maximum cambers, Reynolds numbers and maximum camber locations.

In this work, numerical approach is concerned, and results are obtained based on the finite volume approach. To characterize the effect of corrugated skins, the NACA 0012-corrugated airfoil section is chosen as the base airfoil, and different cambered corrugated airfoil sections are obtained by inclusion the camber to the base airfoil. In this research, the corrugation shape is a sinusoidal wave and corrugated skins are in the aft 30 per cent of airfoil chord. To investigate the effect of corrugations on the cambered sections, the drag coefficient and averaged lift curve slope for the corrugated airfoils are compared to those of the corresponding smooth sections.

Results indicate that the effect of increase in the maximum camber and also Reynolds number on the relative zero-incidence drag coefficient is of little importance at low corrugation amplitudes, whereas at high corrugation, amplitude results in different behaviors. It is found that as the maximum camber increases, the deterioration in the relative curve slope introduced by corrugated skins is reduced, and reduction in this deterioration is significant for high corrugation amplitudes airfoils. It is shown that an increase in the maximum camber location has nearly no effect on the relative zero-incidence drag coefficient and also relative lift curve slope.

The outcome of the present research provides the clues for better understanding of the effect of different corrugations parameters on the aerodynamic performance of the unmanned air vehicles to have as high aerodynamic performance as possible in different mission profiles of such vehicles.

The purpose of this paper is to explore the effects of the camber on gliding and hovering performance of two-dimensional corrugated airfoils. While the flying mechanism of natural flyers remains a myth up to nowadays, the simulation serves as a minor step toward understanding the steady and unsteady aerodynamics of the dragonfly flight.

The lattice Boltzmann method is used to simulate the flow past the cambered corrugated dragonfly airfoil at low Reynolds numbers. For gliding flight, the maximum camber, the distance of the location of maximum camber point from the leading edge and Reynolds number are regarded as control variables; for hovering flight, the maximum camber, the flapping amplitude and trajectory are considered as control variables. Then corresponding simulations are performed to evaluate the implications of these factors.

Greater gliding ratio can be reached by increasing the maximum camber of the dragonfly wing section. When the location of the maximum camber moves backward along the wing chord, large scale flow separation can be delayed. These two effects result in better gliding performances. For hovering performances, it is found that for different flapping amplitudes along an inclined plane, the horizontal force exerted on the airfoils increases with the camber, and the drag growths first but then drops. It is also found that the elliptic flapping trajectory is most sensitive to the camber of the cambered corrugated dragonfly wing section.

The effects of the camber on gliding and hovering performance of the cambered dragonfly wing section are explored in detail. The data obtained can be helpful when designing micro aerial vehicles.

This study seeks to explore the aerodynamic performance of wings with different shapes at low Reynolds numbers.

The airfoils of these wings are made from aluminum plates, and the maximum cord length and wingspan are 15 cm. Wings A to D are plates with 6 percent Gottingen camber but different wing planforms. The forward‐half sections of wings E and F are dragonfly‐like, whereas the rear‐half sections of wings E and F are flat and positively cambered, respectively. The aspect ratios of these wings are close to one, and the ratios of plate thickness to the maximum cord length are 1.3 percent. Experimental results indicate that the wings with Gottingen camber have a superior lift and lift‐to‐drag ratio, whereas the wings with dragonfly‐like airfoils perform well in terms of drag and pitch moment.

The aerodynamic measurements of the wings demonstrate that the wing with the Gottingen camber airfoil, a swept‐back leading edge and a straight trailing edge is suitable for use in micro aerial vehicle (MAV). An MAV is fabricated with this wing and the aerodynamic performance of the MAV is examined and compared with the bare wing data.

This study develops several criteria to the design of MAV‐sized wings. For example, the thickness ratio of airfoil must be small, usually less than 2 percent. Besides, the airfoil must be cambered adequately. Furthermore, a wing planform with a swept‐back leading edge and a straight trailing edge would be contributive to the successful flights of MAVs.

This paper aims to model the aerodynamic flow characteristics of NACA0010 for various angle of attacks including stall for incompressible flows using panel methods. This paper also aims to quantify the surface pressure distribution on streamlined bodies and validate the results with analytical Jukouwski method and inverse panel methods that can predict the aerodynamic flow behaviour using the geometric iteration approach.

The 2 D panel method was implemented in Qblade software v.06 which uses the fundamental panel method which rely on source strengths and influence coefficients to determine the velocity and pressure fields on the surface. The software implements the boundary layer or viscous effects to determine the influence on aerodynamic performance at various angles of attack. Jukouwski method is also evaluated for predicting aerodynamic characteristics and is based on the geometric iteration approach. Then complex aerodynamic flow potentials are determined based on the source strengths which are used to predict the pressure and velocity fields.

At low to moderate angles of attack, panel and Jukouwski methods predict similar results for surface pressure coefficients comparable to Hess and Smith inverse method. In comparison to panel method, results from the Jukouwski mapping method predicted the pressure coefficient conservatively for the same free stream conditions. With increase in Reynolds number, lift coefficient and aerodynamic performance improved significantly for un-tripped aerofoil when stall angle is approached when compared to tripped aerofoil.

This study demonstrated that panel methods have higher efficacy in terms of computational time or resources and thus can provide benefits to many real-world aircraft or aerospace design applications.

Even though panel and Jukouwski methods have been studied extensively in the past, this paper demonstrates the efficacy of both methods for modelling aerodynamic flows that range between moderate to high Reynolds number which are critical for many aircraft applications. Both methods have been validated with analytical and inverse design methods which are able to predict aerodynamic flow characteristics for simple bluff bodies, streamlined aerofoils as well as bio-inspired corrugated aerofoils.

The purpose of this study is to analyze influence of airfoil profile on lateral-directional flying quality of flying wing aircraft. The lateral-directional stability is always insufficient for aircraft with the layout due to the absence of vertical stabilizer. A flying wing aircraft with double-swept wing is used as research object in the paper.

The 3D model is established for the aircraft with flying wing layout, and parametric modeling is carried out for airfoil mean camber line of the aircraft to analyze lateral-directional stability of the aircraft with different camber line parameters. To increase computational efficiency, vortex lattice method is adopted to calculate aerodynamic coefficients and aerodynamic derivatives of the aircraft.

It is found from the research results that roll mode and spiral mode have a little effect on lateral-directional stability of the aircraft but Dutch roll mode is the critical factor affecting flying quality level of such aircraft. Even though changes of airfoil mean line parameters can greatly change assessment parameters of aircraft lateral-directional flying quality, that is kind of change cannot have a fundamental impact on level of flying quality of the aircraft. In case flat shape parameters are determined, the airfoil profile has a limited impact on Dutch roll mode.

Influences of airfoil profile on lateral-directional flying quality of aircraft with double-swept flying wing layout are revealed in the thesis and some important rules and characteristics are also summarized to lay a theoretical basis for design of airfoil and flight control system of aircraft with the layout.

This paper aims to achieve an optimum flow separation control over the airfoil using a passive flow control method by introducing a bio-inspired nose near the leading edge of the National Advisory Committee for Aeronautics (NACA) 4 and 6 series airfoil. In addition, to find the optimised leading edge nose design for NACA 4 and 6 series airfoils for flow separation control.

Different bio-inspired noses that are inspired by the cetacean species have been analysed for different NACA 4 and 6 series airfoils. Bio-inspired nose with different nose length, nose depth and nose circle diameter have been analysed on airfoils with different thicknesses, camber and camber locations to understand the aerodynamic flow properties such as vortex formation, flow separation, aerodynamic efficiency and moment.

The porpoise nose design that has a leading edge with depth = 2.25% of chord, length = 0.75% of chord and nose diameter = 2% of chord, delays the flow separation and improves the aerodynamic efficiency. Average increments of 5.5% to 6° in the lift values and decrements in parasitic drag (without affecting the pitching moment) for all the NACA 4 and 6 series airfoils were observed irrespective of airfoil geometry such as different thicknesses, camber and camber location.

The two-dimensional computational analysis is done for different NACA 4 and 6 series airfoils at low subsonic speed.

This design improves aerodynamic performance and increases the structural strength of the aircraft wing compared to other conventional high lift devices and flow control devices. This universal leading edge flow control device can be adapted to aircraft wings incorporated with any NACA 4 and 6 series airfoil.

The results would be of significant interest in the fields of aircraft design and wind turbine design, lowering the cost of energy and air travel for social benefits.

Different bio-inspired nose designs that are inspired by the cetacean species have been analysed for NACA 4 and 6 series airfoils and universal optimum nose design (porpoise airfoil) is found for NACA 4 and 6 series airfoils.

Since most of the existing literature do not disclose the node coordinate data of its fixed-wing aircraft airfoil, in order to develop and obtain a practical and suitable deformation airfoil for fixed-wing micro air vehicle (MAV), this paper proposes an improved airfoil design method of fixed-wing MAV based on the profile data of S5010 airfoil.

Combined with the body shape variation of the stingray in the propulsion process, the parametric study of the aerodynamic shape of the original design airfoil is carried out to explore the influence of a single parameter change on the aerodynamic performance of the airfoil. Then, according to the influence law of single parameter variation on the aerodynamic performance of the airfoil, the original airfoil is synthetically deformed by changing multiple parameters.

By comparing the aerodynamic performance of the multi-parameter deformed airfoil with the original airfoil, it is found that the lift coefficient of the multi-parameter deformed airfoil changes from negative to positive value when AOA = 0°. When AOA = 2°, the lift coefficient growth rate is the largest, which is 47.27%, and the lift-to-drag ratio is increased by 50.00%. At other angles of attack, the lift, drag, and torque coefficients of the multi-parameter deformed airfoil are optimized to some extent.

Combined the body shape variation of the stingray in the propulsion process, the parametric study of the aerodynamic shape of the original design airfoil is carried out to explore the influence of a single parameter change on the aerodynamic performance of the airfoil.

This study aims to develop an innovative actuator for improving the performance of future aircraft, by adapting the airfoil shape according to the flight conditions. The flap’s camber of a civil regional transportation aircraft’s trailing edge actuated and morphed with the use of shape memory alloys (SMA) actuator technology, instead of the conventional split flap mechanism is studied.

For the flap’s members sizing an efficient methodology is utilised based on finite element (FE) stress analysis combined to analytically formulated design criteria. A mechanical simulation within an FE approach simulated the performance of the moving rib, integrating both aerodynamic loads and SMA phenomenology, implementing Lagouda’s constitutive model. Aim of this numerical simulation is to provide guidelines for further development of the flap. A three-dimensional assembly of the flap is constructed to produce manufacturing drawing and to ensure that during its morphing no interference between the members occurrs. Eventually, the manufactured flap is integrated on a test rig and the experimental characterisations under no and static loads, and dynamic excitation are performed.

Experimental results showed that the rib’s SMA mechanism can adequate function under load providing satisfactory morphing capabilities.

The investigated approach is an internal into the flap mechanism based on the shape memory effect of thin wires. In the developed mechanism, SMA wires are attached to the wing structure, where they function as actuating elements.

The purpose of this paper is to present a fast, economical and practical method for mathematical modeling of aerodynamic characteristics of rectangular wing in ground (WIG) effect.

Reynolds averaged Navier–Stokes (RANS) equations were converted to Bernoulli equation by reasonable assumptions. Also, Helmbold’s equation has been developed for calculation of the slope of wing lift coefficient in ground effect by defining equivalent aspect ratio (ARe). Comparison of present work results against the experimental results has shown good agreement.

A practical mathematical modeling with lower computational time and higher accuracy was presented for calculating aerodynamic characteristics of rectangular WIG effect. The relative error between the present work results and the experimental results was less than 8 per cent. Also, the accuracy of the proposed method was checked by comparing with the numerical methods. The comparison showed fairly good accuracy.

Aerodynamic surfaces in ground effect were used for reducing wetted surface and increasing speed in high-speed marine and novel aeronautical vehicles.

The proposed method is useful for investigation of aerodynamic performance of WIG vehicles and racing boats with aerodynamic surfaces in ground effect.

The proposed method has reduced the computational time significantly as compared to numerical simulation that allows conceptual design of the WIG crafts and is also economical.

The purpose of this paper is to investigate the unsteady aerodynamic characteristics in the deflection process of a morphing wing with flexible trailing edge, which is based on time-accurate solutions. The dynamic effect of deflection process on the aerodynamics of morphing wing was studied.

The computational fluid dynamic method and dynamic mesh combined with user-defined functions were used to simulate the continuous morphing of the flexible trailing edge. The steady aerodynamic characteristics of the morphing deflection and the conventional deflection were studied first. Then, the unsteady aerodynamic characteristics of the morphing wing were investigated as the trailing edge deflects at different rates.

The numerical results show that the transient lift coefficient in the deflection process is higher than that of the static case one in large angle of attack. The larger the deflection frequency is, the higher the transient lift coefficient will become. However, the situations are contrary in a small angle of attack. The periodic morphing of the trailing edge with small amplitude and high frequency can increase the lift coefficient after the stall angle.

The investigation can afford accurate aerodynamic information for the design of aircraft with the morphing wing technology, which has significant advantages in aerodynamic efficiency and control performance.

The dynamic effects of the deflection process of the morphing trailing edge on aerodynamics were studied. Furthermore, time-accurate solutions can fully explore the unsteady aerodynamics and pressure distribution of the morphing wing.