Search results

To treat water pollution, especially the contamination resulted from organic dyes has aroused significant attention around the world, this study aims to prepare the metal organic framework (MOF) materials hybridizing with poly(p-phenylene terephthalamide) (PPTA) by means of a facile refluxing method and to systematically investigate adsorption performance for anionic dye Congo red as target molecule from aqueous solution.

The MOF materials hybridized by PPTA were fabricated by virtue of a facile refluxing method, characterized by thermogravimetric analysis, X-ray powder diffraction, Fourier transform infrared and pore structure.

The results showed that pseudo-second-order kinetic model could better describe the adsorption process for all the four materials, whereas Elovich model also fitted the process for the hybrid materials with PPTA. Adsorption isotherm analyses indicated that Langmuir isotherm could be used to describe the adsorption process. Introduction of appropriate amount of PPTA could enhance the adsorption affinity of the MOF materials for Congo red, and the maximum adsorption capacity could reach as high as 1,053.41 mg/g while that of the MOF material without PPTA was 666.67 mg/g, indicating introduction of PPTA could change the microenvironment of the MOF materials and increase the adsorption sites, leading to high adsorption efficiency.

The microstructure of MOF hybridized materials in detail is the further and future investigation.

This study will provide a method to prepare MOF materials with high efficiency to treat anionic dyes like Congo red from aqueous solution.

Owing to the special characteristics of PPTA and similar to carbon tube, PPTA was introduced into MOF material to increased corresponding water stability. Because of aromatic ring and amide group on the surface of PPTA, the adsorption efficiency of the hybridized MOF material with appropriate amount of PPTA was greatly enhanced.

Water is a vital natural resource without which life on earth would be impossible. Properties of synthetic dyes like high stability and noxious nature make it difficult to remove them from the effluent. This review focuses on the removal of synthetic dyes using nanoparticles (NPs) based on the adsorption principle.

Adsorption technique is widely used to remove synthetic dyes from their aqueous solution for decades. Synthetic dye removal using NPs is promising, less energy-intensive and has become popular in recent years. NPs are in high demand for treating wastewater using the adsorption principle due to their tiny size and vast surface area. To maximise environmental sustainability, the utilisation of green-produced NPs as efficient catalysts for dye removal has sparked attention amongst scientists.

This review has prioritised research and development of optimal dye removal systems that can be used to efficiently remove a large quantity of dye in a short period while safeguarding the environment and producing fewer harmful by-products. The removal efficiency of synthetic dye using different NPs in wastewater treatment varies mostly between 75% to almost 100%. This review will aid in the scaling up of the wastewater treatment process.

There is a lack of research emphasis on the safe disposal of NPs once the reuse efficiency significantly drops. The relevance of cost analysis is equally critical, yet only a few papers discuss cost-related information.

Comprehensive and planned research in this area can aid in the development of long-term wastewater treatment technology to meet the growing need for safe and reliable water emphasising reuse and desorption efficiency of the NPs.

This study aims to activated carbon prepared from pistachio waste by using phosphoric acid as chemical activator agent. Activated carbon adsorbents were prepared from pistachio waste by using phosphoric acid as chemical activator agent.

The optimum conditions for the highest adsorption performance were determined by central composite design (CCD). The adsorbent was used for the adsorption of dye reactive black 5 (RB5), and the parameters affecting the adsorption were discussed like pH, initial concentration, contact time and adsorbent dosage. The adsorbent synthesized has been characterized by FTIR spectroscopy and scanning electron microscopy. The kinetic models including pseudo-first-order, pseudo-second-order and intraparticle diffusion with Langmuir and Freundlich isotherm models were applied to investigate the kinetic and isotherms parameters.

When the dye concentration is 10 mg/L, RB5 dye removal rates reach 87.5 per cent. Moreover, the adsorption process of RB5 follows the pseudo-second-order kinetics and the Freundlich adsorption isotherm.

This study provided a simple and effective way to prepare activated carbon adsorbents from pistachio wastes. This way was conductive to protect environmental from a huge amount of agricultural waste produced and subsequent application for removal of pollutants from aqueous solutions.

The activated carbon adsorbents are prepared via chemical activation, which is prepared with pistachio wastes. There are two main innovations: one is that the novel adsorbents are prepared successfully by waste and the other is that the optimized conditions are designed by CCD.

This study’s aim is to introduce a high-performance sorbent for the removal of both anionic (Congo red; CR) and cationic (methylene blue; MB) dyes from aqueous solutions.

Sodium silicate is adopted as a substrate for GO and AgNPs with positive charge are used as modifiers. The synthesized nanocomposite is characterized by FTIR, FESEM, EDS, BET and XRD techniques. Then, some of the most effective parameters on the removal of CR and MB dyes such as solution pH, sorbent dose, adsorption equilibrium time, primary dye concentration and salt effect are optimized using the spectrophotometry technique.

The authors successfully achieved notable maximum adsorption capacities (Qmax) of CR and MB, which were 41.15 and 37.04 mg g⁻¹, respectively. The required equilibrium times for maximum efficiency of the developed sorbent were 10 and 15 min for CR and MB dyes, respectively. Adsorption equilibrium data present a good correlation with Langmuir isotherm, with a correlation coefficient of R2 = 0.9924 for CR and R2 = 0.9904 for MB, and kinetic studies prove that the dye adsorption process follows pseudo second-order models (CR R2 = 0.9986 and MB R2 = 0.9967).

The results showed that the proposed mechanism for the function of the developed sorbent in dye adsorption was based on physical and multilayer adsorption for both dyes onto the active sites of non-homogeneous sorbent.

The as-prepared nano-adsorbent has a high ability to remove both cationic and anionic dyes; moreover, to the high efficiency of the adsorbent, it has been tried to make its synthesis steps as simple as possible using inexpensive and available materials.

This study aims to prepare an imprinted composite membrane with grafted temperature-sensitive blocks for the efficient adsorption and separation of rhenium(Re) from aqueous solutions.

PVDF resin membrane was used as the substrate, dopamine and chitosan (CS) were used to modify the membrane surface and temperature-sensitive block PDEA was grafted on the membrane surface. Then acrylic acid (AA) and N-methylol acrylamide (N-MAM) were used as the functional monomers, ethyleneglycol dimethacrylate (EGDMA) as the cross-linker and ascorbic acid-hydrogen peroxide (Vc-H₂O₂) as the initiator to obtain the temperature-sensitive ReO4⁻ imprinted composite membranes.

The effect of the preparation process on the performance of CS–Re–TIICM was investigated in detail, and the optimal preparation conditions were as follows: the molar ratios of AA–NH₄ReO₄, N-MAM and EGDMA were 0.13, 0.60 and 1.00, respectively. The optimal temperature and time of the reaction were 40 °C and 24 h. The maximum adsorption capacity of CS–Re–TIICM prepared under optimal conditions was 0.1071 mmol/g, and the separation was 3.90 when MnO4⁻ was used as the interfering ion. The quasi first-order kinetics model and Langmuir model were more suitable to describe the adsorption process.

With the increasing demand for Re, the recovery of Re from Re-containing secondary resources becomes important. This study demonstrated a new material that could be separated and recovered Re in a complex environment, which could effectively alleviate the conflict between the supply and demand of Re.

This contribution provided a new material for the selective separation and purification of ReO4⁻, and the adsorption capacity and separation of CS–Re–TIICM were increased with 1.673 times and 1.219 time compared with other Re adsorbents, respectively. In addition, when it was used for the purification of NH₄ReO₄ crude, the purity was increased from 91.950% to 99.999%.

This study aims to model and investigate Basic Yellow 28 (BY28) adsorption onto activated carbon in batch and continuous process.

Batch adsorption experiments were carried out at 25 °C with 50 mg/L BY28 solution at pH 6 with different amounts of activated carbon. Freundlich and Langmuir adsorption isotherm models were used to model batch data. Pseudo-first-order and pseudo-second-order kinetic models were applied with linear regression. The changes of the breakthrough curve with the column height, flow rate, column diameter and adsorbent amount were examined in fixed bed column at room temperature. BY28 adsorption data were modelled by using different adsorption column models (Adams & Bohart, Thomas, Yoon & Nelson, Clark and modified dose–response) with non-linear regression.

Freundlich model and pseudo-second-order kinetic model expressed the experimental data with high compatibility. Modified dose-response model corresponded to the fixed bed column data very well.

Adsorption of Basic Yellow 28 on activated carbon in a fixed bed column was studied for the first time. Continuous adsorption process was modelled with theoretical adsorption models using non-linear regression.

This study aims to observe the coloring efficacy of graphite (G) and nano bentonite clay (BCNPs) on the adsorption of Basic Blue 5 dye from residual dye bath solution.

Some factors that affected the adsorption processes were examined and found to have significant impacts on the adsorption capacity such as the initial concentration of G and/or BCNPs (Co: 40–2,320 mg/L), adsorbent bath pH (4–9), shaking time (30–150 min.) and initial dye concentration (40–200 mg/L). The adsorption mechanism of dye by using G and/or BCNPs was studied using two different models (first-pseudo order and second-pseudo order diffusion models). The equilibrium adsorption data for the dye understudy was analyzed by using four different models (Langmuir, Freundlich, Temkin modle and Dubinin–Radushkevich) models.

It has been found that the adsorption kinetics follow rather a pseudo-first-order kinetic model with a determination coefficient (R²) of 0.99117 for G and 0.98665 for BCNPs. The results indicate that the Freundlich model provides the best correlation for G with capacities q_max = 2.33116535 mg/g and R² = 0.99588, while the Langmuir model provides the best correlation for BCNPs with R² = 0.99074. The adsorbent elaborated from BCNPs was found to be efficient and suitable for removing basic dyes rather than G from aqueous solutions due to its availability, good adsorption capability, as well as low-cost preparation.

There is no research limitation for this work. Basic Blue 5 dye graphite (G) and nano bentonite clay (BCNPs) were used.

This work has practical applications for the textile industry. It is concluded that using graphite and nano bentonite clay can be a possible alternative to adsorb residual dye from dye bath solution and can make the process greener.

Socially, it has a good impact on the ecosystem and global community because the residual dye does not contain any carcinogenic materials.

The work is original and contains value-added products for the textile industry and other confederate fields.

The purpose of this study is to prepare Polystyrene grafted with Zeolite Y (Zeosty) for Uranyl ion [U(VI)] adsorption from aqueous solution. The adsorption mechanism has been explained by studying kinetic, isothermal and thermodynamic models.

Polystyrene was grafted with Zeosty by a simple hydrothermal technique. Zeosty was characterized by different techniques such as X-ray diffraction, scanning electron microscope, energy dispersive X-ray and Infrared spectroscopy to confirm its structure and its molecular composition. Zeosty was used for U(VI) adsorption from an aqueous solution in a series of batch experiments. The effects of pH, contact time, initial U(VI) concentration and temperature on the adsorption process were investigated.

The results showed that the adsorption of U(VI) on the prepared reached equilibrium at pH 6 with a removal efficiency of 98.9%. Adsorption kinetics and isotherms models are studied on the experimental data to estimate the mechanism of the adsorption reaction was chemisorption and homogenous reaction. The activity of Zeosty increased at high temperatures, resulting in the adsorption capacity increase. Thermodynamic parameters ΔGo, ΔHo and ΔSo indicate that the adsorption processes are spontaneous and endothermic. Zeosty has an effective surface and could be considered a valuable adsorbent for U(VI) removal from aqueous waste. A comparison study proves that the new adsorbent has high effective behavior in the adsorption process, and it is considered a new reliable adsorbent for U(VI) removal from wastewater.

This study is complementary to the previous study using the same technique to prove that the effective fine particle adsorbents need solid support to enhance their absorption capacities.

The purpose of this study was to the synthesis of Fe₃O₄@SiO₂ nanocomposites and using it as an adsorbent for removal of diazinon from aqueous solutions. Structural characteristics of the synthesized magnetic nanocomposite were described by Fourier transform infrared spectroscopy and scanning electron microscopy.

The effects of different parameters including pH (2-10), contact time (1-180 min), adsorbent dosage (100-2000 mg L⁻¹) and initial diazinon concentration (0.5–20 mg L⁻¹) on the removal processes were studied. Finally, isotherm and kinetic and of adsorption process of diazinon onto Fe₃O₄@SiO₂ nanocomposites were investigated.

The maximum removal efficiency of diazinon (96%) was found at 180 min with 1000 mg L⁻¹ adsorbent dosage using 0.5 mg L⁻¹ diazinon concentration at pH = 7. The experimental results revealed that data were best fit with the pseudo-second-order kinetic model (R² = 0.971) and the adsorption capacity was 10.90 mg g⁻¹. The adsorption isotherm was accordant to Langmuir isotherm.

In the present study, the magnetic nanocomposites were synthesized and used as an absorbent for the removal of diazinon. The developed method had advantages such as the good ability of Fe₃O₄@SiO₂ nanocomposites to remove diazinon from aqueous solution and the magnetic separation of this absorbent that make it recoverable nanocomposite. The other advantages of these nanocomposites are rapidity, simplicity and relatively low cost.

The main purpose of this paper is to investigate the adsorption properties of CoFe_1.9Mo_0.1O₄ magnetic nanoparticles (CFMo MNPs) using, anionic dye “congo red (CR)” as a model of water pollutants.

The magnetic nano-adsorbent was synthesized via sol-gel process. Different techniques including; Fourier transform infrared spectroscopy, point of zero charge, scanning electron microscope and X-ray powder diffraction were used to characterize the prepared adsorbent. Adsorption experiments were conducted in batch mode under various conditions (contact time, shaking speed, initial dye concentration, initial solution pH, solution temperature and adsorbent amount) to investigate the adsorption capability of CFMo MNPs for CR.

The results showed that, CFMo MNPs could successfully remove more than 90% of CR dye within 20 min. Adsorption kinetics and isotherms were better described using pseudo-second-order (PSO) and Langmuir models, respectively. The maximum adsorbed amount (q_max) of CR dye was 135.14 mg/g. The adsorption process was found to be endothermic and spontaneous in nature as demonstrated by the thermodynamics ( ΔGo, ΔHoand ΔSo).

This study provided a good example of using an easily separated magnetic nano-adsorbent for fast removal of a very toxic organic pollutant, congo red, from the aquatic environment

The employment of Mo-doped cobalt ferrite for the first time for removing hazardous anionic dyes such as congo red from their aqueous solutions.