Search results

This paper aims to present the influence of glass bead concentration in a matrix of polyamide on wear and several three-dimensional (3D) parameters of the surface texture when the composite is sliding on steel in dry contact.

There were mold disks with the following concentrations in glass beads: 2.5, 5.0, 10, 20, 30 and 50 per cent. The mix of glass beads has diameters in the range of several microns to 50 microns. Tests were done on a pin-on-disk tribotester, in dry regime, for the following parameters: average pressure (1, 2 and 3 MPa) and sliding speed (0.5, 1.0 and 1.5 m/s). Zones of 500 × 500 μm were investigated from worn tracks generated on the composite disks, and the average values of several 3D texture parameters were analyzed.

The authors plotted maps indicating no correlation between the glass bead concentration and the parameters characterizing the surface quality (amplitude parameters and functional parameters). Composites with concentrations of 10[…]30 per cent glass beads generated worn surfaces with better quality as compared to composites with extreme concentrations: low (2.5 and 5 per cent) and high (50 per cent).

This set of parameters allows for evaluating the influence of regime parameters on the surface quality, by comparing the obtained values before and after sliding, and this evolution of roughness parameters could give recommendations for selecting the friction couple of materials for particular contacts that function with repeated starts and stops.

The results encourage the researchers to use a set of 3D texture parameters instead of “classical” two-dimensional parameters, the arithmetic mean deviation of the profile, Ra, because this set of parameters better evaluate the surface quality, especially for worn surfaces.

This paper aims to present an analysis of several 3 D texture parameters for the entire wear scars obtained in severe regime, on a four-ball tester. The aim of this analysis is to correlate the tribological parameter as wear scar diameter to texture parameters.

Tested lubricants were rapeseed oil, rapeseed oil additivated with 1% Wt nano TiO₂ and rapeseed oil additivated with 1%Wt nano ZnO. The severe regime was applied for 1400 rpm and for loads increasing in steps of 50 N, from 500 to 900 N. Several analyzed roughness parameters (height parameters and functional ones) could be related to the evolution of a wear parameter, the wear scar diameter. Comparing the values for neat rapeseed oil and additivated variants, the texture parameters allow for evaluating if the additives protect or not the worn surfaces.

Measurements pointed out two groups of roughness parameters: one that has an evolution depending on wear scar diameter (WSD) and load (Sa, St, functional parameters) and one including Ssk that has shown no dependence on load and WSD. Also, the functional parameters Spk and Svk follow in a similar manner the wear parameter, WSD, but Sk is the least dependent on load. For the highest load, amplitude parameters such as Sa and St are following the tendency of WSD. Each lubricant has its particular correlation between wear parameters and texture quality, expressed by the help of a set of roughness parameters.

Such studies help tribologists to rank lubricants based on a combined analysis with wear parameters and texture parameters.

The results allow for evaluating new formulated lubricants.

The study on the quality on worn surfaces introduces the original idea of analyzing the entire wear scar surface (approximated by an ellipse with the axes as those experimentally measured) by the help of a set of 3 D roughness parameters.

Electrical discharge machining (EDM) is well-known for its credibility in the processing of advanced materials, which are electrically conductive. The strenuous effort associated with machining of Ti6Al4V (Ti64) using conventional methods, and its low tribological behavior, present an immediate need to develop solutions to monitor and improve the compatible techniques such as EDM.

The present work includes following: monitoring the ED process parameters, namely, current (I) and pulse on time (T_on), in controlling the material removal rate and surface roughness (R_a and S_a) for development of tribo-adaptive surfaces; and investigation on the role of oxides pertinent to the tribo-behavior of Ti64 (bare and EDMed) surfaces.

The tribological behavior of Ti6Al4V surfaces got remarkably improved through ED machining, which points to the credibility of the process to establish itself as a surface alloying technique. The recast layer (RL, alloyed matrix) acted as a protective coating; stable enough to assist the developed tribo-oxides such as TiO and Ti₈O₁₅ in rendering improved sliding performance at load = 50 N and speed = 0.838 ms⁻¹.

The surface modification through ED machining was experimentally proven to improve the wear behavior of Ti6Al4V surfaces.

This empirical study aims to investigate the erosion wear performance of two different 3D-printed materials (acrylonitrile butadiene styrene [ABS] and polylactic acid [PLA]) with various micro textures. The two different textures (prism and square) were created over the surfaces of both materials by using the 3D-printed technique.

The erosion experiments on both materials were performed by using Ducom Erosion Jet Tester. Erosion tests were performed at four different impacting velocities (15, 30, 45 and 60 m/s) with the four different particle sizes (17, 39, 63 97 µm) at the impact angles (30°–90°) for the time duration of 5, 10, 15 and 20 min. The two different textures prism and cone were used for performing the erosion experiments. Taguchi’s orthogonal L16 (mixed level) was used to reduce the number of experiments and to determine the impact of these parameters on erosion wear performance of both 3D-printed materials.

The PLA with cone texture was found to be best (against erosion) than the ABS cone and prism textures due to their high hardness (68 HV). Also, the average signal to noise (S/N) ratio for PLA and ABS was measured as 56.4 and 44.4 dB, respectively. As the value of the S/N ratio is inversely proportional to the erosion rate, the PLA has the least erosion rate as compared to the ABS. The sequence of erosion wear influencing parameters for both materials was in the following order: velocity > erodent size > texture > impact angle > time interval.

Both PLA and ABS with different micro textures for erosion testing were studied with Taguchi’s optimization method, and the erosion mechanisms are well analyzed by using scanning electron microscopy and Image J techniques.

Micro-texture is processed on the surface to reduce the friction of the contact surface, and its application is more and more extensive. The purpose of this paper is to create a texture function model to study the influence of surface parameters on the accuracy of the simulated surface so that it can more accurately reflect the characteristics of the real micro-textured surface.

The microstructure function model of rough surfaces is established based on fractal geometry and polar coordinate theory. The offset angle θ is introduced into the fractal geometry function to make the surface asperity normal perpendicular to the tangent of the surface. The 2D and 3D contour surfaces of the surface groove texture are analyzed by MATLAB simulation. The effects of fractal parameters (D and G) and texture parameter h on the curvature of the surface micro-texture model were studied.

This paper more accurately characterizes the textured 3D curved surface, especially the surface curvature. The scale coefficient G significantly affects curvature, and the influence of fractal dimension D and texture parameters on curvature can be ignored.

The micro-texture model of the rough surface was successfully established, and the range of fractal parameters was determined. It provides a new method for the study of surface micro-texture tribology.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-09-2023-0298/

The purpose of this paper is to use a combination of numerical simulation and experiment to evaluate the performance of laser surface texturing (LST) in the field of gear lubrication, and to more accurately predict the lubrication characteristics of different surfaces.

The method used in this paper is developed on the basis of the deterministic solution of the three-dimensional (3D) mixed elasto-hydrodynamic lubrication (EHL) model and the model parameters are corrected by friction test. The film pressure, film thickness and friction coefficient of different micro-textured tooth surfaces are predicted on the basis of accurate 3D mixed EHL models.

The results demonstrate that the micro-texture structure of the tooth surface can increase the local film thickness and enhance the lubricating performance of the tooth surface without drastically reducing the contact fatigue life. The stress distribution and friction characteristics of the tooth surface can be optimized by adjusting the micro-texture arrangement and the size of the micro-textures.

A new evaluation method using a 3D hybrid EHL model and friction test to predict the lubrication characteristics of LST is proposed, which can effectively improve the processing economy and save time.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2020-0423

Dynamic spreading and wetting on the rough surfaces is complicated, which directly affects the fluxion and phrase transition properties of the fluid. This paper aims to enhance our knowledge of the mechanism of micro-texture lubrication from interface wettability and provide some guidance for the practical manufacturing of the surfaces with special wettability and better lubrication characteristics.

The effect of surface topography on the wetting behavior of both smooth and rough hydrophilic surfaces was investigated using a combination of experimental and simulation approaches. Four types of patterns with different topographies were designed and fabricated through laser surface texturing. The samples were measured with a non-contact three-Dimensional (3D) optical profiler and were parameterized based on ISO 25178. Quantitative research on the relevancy between the topography characteristic and wettability was conducted with several 3D topography parameters.

Results show that for the surfaces with isotropic textures, topography with a small skewness (S_sk) and a large kurtosis (S_ku) exhibits better wettability and spreading behavior. For the surfaces with anisotropic textures (smaller texture aspect ratio, S_tr), dominant textures (such as long groove, rectangle) play a significant guiding role in promoting spreading. In addition, the moving mechanism of the triple contact line and anisotropic spreading were also studied using a computational fluid dynamics simulation. The simulation results have a good adherence with the experimental results.

Most of the surface characterization methods at present remain at a level that is related to geometric description, and the topography parameters are limited to 2D roughness parameters. So in present study, the relevancy between wettability and 3D surface topography parameters is explored. The authors believe that the current work provides a new viewpoint to the relevancy between surface topography and wettability.

Realistic geometric description is essential for simulating physical properties of warp-knitted velvet fabrics, which are widely used for home-textiles and garments. The purpose of this paper is to provide an approach to the description of patterned piles and propose a customized simulation model to realize highly real-time simulation of warp-knitted velvet fabrics in three dimensions.

Based on knitting technology and structure features, a mathematical model to qualify forming possibility of piles is conducted by assessing underlaps of pattern bars and pile ground bars. When the pile areas and ground areas are classified, a three-dimensional (3D) space coordinate is built, of which the z-axis is divided into equal spaces to form certain multi-layer textured slices. Color and transparency of piles on each textured slice can be computed and generated by mapping to 3D geometrical grid layers with particular mapping relationship. Moreover, piles’ deflection and spatial collision are also taken into account to make sure high uniformity with real fabrics.

According to the models built, a simulator special for warp-knitted patterned velvet fabrics is programed via Visual C++ and the models are proven practical and easily implemented by comparing simulated effect of one sample with real fabric.

Because of present limited research, 3D simulation of patterned velvet fabrics knitted on double-needle bar Raschel machine as well as 3D shadow effect will be studied in the further research.

The paper includes implications for designing patterned velvet products and shows convenience to instantly see finished effect without sampling on machine.

This paper fulfills a featured simulation method for warp-knitted patterned velvet fabrics in 3D dimensions for the first time.

The purpose of this study is to investigate the influence of surface texture on the subsurface characteristics of contact interfaces under elastohydrodynamic lubrication condition. As a typical contact form of gears and bearings, the optimization of friction characteristics at the elastohydrodynamic lubrication (EHL) interface has attracted the attention of scholars. Laser surface texturing is a feasible optimization solution, but there have been concerns about whether the surface texture of high-pair parts will affect their fatigue life.

To examine the impact of texture preparation on the subsurface characteristics of high-pair interfaces under EHL conditions, a point contact EHL model is developed that takes into account the effect of textured surface topography. The pressure and thickness of the oil film are calculated as input parameters under different loads and entrainment velocities. The finite element method is used to simulate the impact of textures with varying diameters, densities and depths on the subsurface characteristics of the elastohydrodynamic interface. According to ISO 25178, analyze the relationship between 3D topography parameters and subsurface characteristics and study the trend of friction characteristics and subsurface characteristics based on the results of the ball on disc friction tests.

The outcomes suggest that under different rotational velocity and load conditions, the textured surfaces exhibit improved friction reduction effects; however, the creation of textures can result in significant subsurface plastic deformation and local peeling. The existence of texture makes the larger stress zone in the subsurface layer closer to the surface, leading to fatigue failure near the surface. Reasonable design parameters can help enhance the attributes of the subsurface. A smaller Sa and a Str greater than 0.5 can achieve ideal subsurface properties on the textured surface.

This paper investigates the influence of surface texture on the friction and subsurface characteristics of EHL interfaces and analyzes the impact of surface texture on interface contact performance while achieving lubrication improvement functional characteristics. The results provide theoretical support for the optimization design and functional regulation of surface texture in EHL interfaces.

The peer review history for this article is https://publons.com/publon/10.1108/ILT-10-2023-0324/

Gears are prone to instantaneous failure when operating under extreme conditions, affecting the machinery’s service life. With numerous types of gear meshing and complex operating conditions, this study focuses on the gear–rack mechanism. This study aims to analyze the effects and optimization of biomimetic texture parameters on the line contact tribological behavior of gear–rack mechanisms under starvation lubrication conditions.

Inspired by the microstructure of shark skin surface, a diamond-shaped biomimetic texture was designed to improve the tribological performance of gear–rack mechanism under starved lubrication conditions. The line contact meshing process of gear–rack mechanisms under lubrication-deficient conditions was simulated by using a block-on-ring test. Using the response surface method, this paper analyzed the effects of bionic texture parameters (width, depth and spacing) on the tribological performance (friction coefficient and wear amount) of tested samples under line contact and starved lubrication conditions.

The experimental results show an optimal proportional relationship between the texture parameters, which made the tribological performance of the tested samples the best. The texture parameters were optimized by using the main objective function method, and the preferred combination of parameters was a width of 69 µm, depth of 24 µm and spacing of 1,162 µm.

The research results have practical guiding significance for designing line contact motion pairs surface texture and provide a theoretical basis for optimizing line contact motion pairs tribological performance under extreme working conditions.