Search results

Dynamic spreading and wetting on the rough surfaces is complicated, which directly affects the fluxion and phrase transition properties of the fluid. This paper aims to enhance our knowledge of the mechanism of micro-texture lubrication from interface wettability and provide some guidance for the practical manufacturing of the surfaces with special wettability and better lubrication characteristics.

The effect of surface topography on the wetting behavior of both smooth and rough hydrophilic surfaces was investigated using a combination of experimental and simulation approaches. Four types of patterns with different topographies were designed and fabricated through laser surface texturing. The samples were measured with a non-contact three-Dimensional (3D) optical profiler and were parameterized based on ISO 25178. Quantitative research on the relevancy between the topography characteristic and wettability was conducted with several 3D topography parameters.

Results show that for the surfaces with isotropic textures, topography with a small skewness (S_sk) and a large kurtosis (S_ku) exhibits better wettability and spreading behavior. For the surfaces with anisotropic textures (smaller texture aspect ratio, S_tr), dominant textures (such as long groove, rectangle) play a significant guiding role in promoting spreading. In addition, the moving mechanism of the triple contact line and anisotropic spreading were also studied using a computational fluid dynamics simulation. The simulation results have a good adherence with the experimental results.

Most of the surface characterization methods at present remain at a level that is related to geometric description, and the topography parameters are limited to 2D roughness parameters. So in present study, the relevancy between wettability and 3D surface topography parameters is explored. The authors believe that the current work provides a new viewpoint to the relevancy between surface topography and wettability.

This paper aims to analyze changes in the surface topography of the work rolls during skin passing. Cold rolled steel sheets are additionally subject to skin pass rolling to form an appropriate surface topography. This operation should facilitate the process of further metal forming of steel sheets, such as deep drawing, painting, etc. The surface topography of steel sheets is determined by the surface topography of the work rolls as well as the skin pass rolling parameters (rolling speed, elongation, roll force, etc.). Suitable preparation and selection of roll surface topography influences the degree of rolls wear and the surface topography of steel sheets as well.

Two-dimensional (2D) and three-dimensional (3D) roughness measurements of work roll surface before, during and after finishing of skin pass rolling of steel sheets are presented in the paper. The measurements were performed on four sets of work rolls with different surface topography.

The appearance of the surface of rolls obtained from the analysis of 3D roughness, the values of selected parameters of the 3D roughness and relative changes of the roughness parameter Ra/Sa depending on the length of the skin passed steel sheets are presented.

The wear of rolls is different depending on work surface topography.

The aim of this paper is to analyze changes in the surface topography of the work rolls during skin passing. It was expected that the surface of work rolls with more summits at similar average roughness Ra will change much faster than the surface with fewer summits. For this purpose, preliminary tests were performed in an industrial environment on four pairs of work rolls, including two pairs of rolls that were hard chromium-plated.

The purpose of this paper is to study the influence of the processing parameters of diamond wire sawing on surface morphology and roughness.

First, a wire saw cutting model is established to determine the positional relationship between a wire saw and the machined surface of the workpiece, and the abrasive grain cutting trajectory is generated. Through the data processing of the cutting trajectory, the simulation of the three-dimensional surface topography of the slice and the calculation of the surface roughness are realized by using the GUI programming of MATLAB. Finally, different surface roughness values are obtained by changing the machining parameters (saw wire speed and workpiece feed speed).

The conclusion is that the surface roughness of the slice is larger when the feed speed is higher and smaller when the linear speed is higher.

Diamond wire saw cutting is the first process of chip processing, and its efficiency and quality have an important impact on subsequent processing. This paper will focus on the influence of the sawing wire cutting processing parameters (sawing wire speed and workpiece feed speed) on the surface roughness to optimize the processing parameters and obtain smaller surface roughness values. Through MATLAB three-dimensional simulation, the surface morphology can be observed more intuitively, which provides a theoretical basis for improving the processing quality.

The purpose of this paper is to provide a static friction coefficient prediction model of rough contact surfaces based on the contact mechanics analysis of elastic-plastic fractal surfaces.

In this paper, the continuous deformation stage of the multi-scale asperity is considered, i.e. asperities on joint surfaces go through three deformation stages in succession, the elastic deformation, the elastic-plastic deformation (the first elastic-plastic region and the second elastic-plastic region) and the plastic deformation, rather than the direct transition from the elastic deformation to the plastic deformation. In addition, the contact between rough metal surfaces should be the contact of three-dimensional topography, which corresponds to the fractal dimension D (2 < D < 3), not two-dimensional curves. So, in consideration of the elastic-plastic deformation mechanism of asperities and the three-dimensional topography, the contact mechanics of the elastic-plastic fractal surface is analyzed, and the static friction coefficient nonlinear prediction model of the surface is further established.

There is a boundary value between the normal load and the fractal dimension. In the range smaller than the boundary value, the normal load decreases with fractal dimension; in the range larger than the boundary value, the normal load increases with fractal dimension. Considering the elastic-plastic deformation of the asperity on the contact surface, the total normal contact load is larger than that of ignoring the elastic-plastic deformation of the asperity. There is a proper fractal dimension, which can make the static friction of the contact surface maximum; there is a negative correlation between the static friction coefficient and the fractal scale coefficient.

In the mechanical structure, the research and prediction of the static friction coefficient characteristics of the interface will lay a foundation for the understanding of the mechanism of friction and wear and the interaction relationship between contact surfaces from the micro asperity-scale level, which has an important engineering application value.

Hydro-viscous drive (HVD) clutches are widely used in equipment requiring soft start, such as fans and pumps, to transmit torque and adjust speed by changing the gap distance between friction pairs. This paper aims to propose a novel two-parameter evaluation method for HVD during the mixed lubrication stage. The objective is to develop an effective model that establishes the relationship between these parameters and the actual surface topography.

In the presented methods, the fractal features of the real manufacturing surface are calculated based on the power spectrum function by the ultra-depth three-dimensional microscope. After that, the hybrid friction model of the friction plate is established based on mixed elasto-hydrodynamic lubrication theory, boundary friction model and fractal theory. Then the torque and load bearing characteristics of the clutch are obtained, and the influences of the surface fractal features are investigated and discussed. Finally, the Weierstrass–Mandelbrot function is adopted for the surface topography characterization and evaluation.

The results indicate that the proposed method exhibits good accuracy, while the speed difference between the friction pair exceeds 2,500 rpm. It is concluded that this paper proposed a way to evaluate the torque and loading capacity of HVD considering the real manufacturing surface topography and is helpful for surface optimization.

The originality and value of this study lie in its development of a novel torque and load bearing capacity evaluation method for HVD in mixed lubrication stage, considering manufacturing surface topography and describing the real manufacturing surface.

This study aims to research the influence mechanism of microtextured geometric parameters of dry gas seal end face on the tribological behavior under dry frictional conditions.

The microtexture was processed using laser processing, while the diamond-like carbon (DLC) film was applied through magnetron sputtering; the experimental platform of friction vibration was established, the frictional and vibrational properties of different geometric parameters were tested; the data signals of vibrational acceleration and frictional torque were collected and processed using data acquisition instrument. The entropy characteristic parameters of 3D vibrational acceleration were extracted based on wavelet packet decomposition method. The end-face topography was measured with ST400 three-dimensional noncontact surface topography instrument.

The geometry of pits plays a key role in influencing friction performance; the permutation entropy and fuzzy entropy of the vibration acceleration signal changed with variations in microtextured parameters. A textured surface with appropriately size parameters can trap debris, enhance the dynamic pressure effect, reduce impact between the friction interfaces and improve the frictional vibrational performance. In this research, microtextured surface with Φ150 µm-10% and Φ200 µm-5% can effectively reduce friction and vibration between the end faces of a dry gas seal.

DLC film improves the hardness of seal ring end face, and microtexture improves the dynamic effect; the tribological behavior monitoring can be realized by analyzing the characteristics of vibration acceleration sensitive parameter with friction state. The findings will provide a basis for further research in the field of tribology and the microtexture optimization of dry gas seal ring end face.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2023-0389/

Although dependence of contact surface temperatures between rough sliding bodies on surface topography is more explicitly described in terms of three‐dimensional (3D) topographic parameters, no work has yet been reported on this aspect. The paper seeks to carry out experiments to systematically correlate the 3D surface parameters to the contact temperature rise.

The surface temperatures at the contact between a relatively smooth zinc sulphide pin held against a rotating mild steel disc of varying surface topography were measured using an infrared thermal imaging system under different load and sliding velocity conditions. The main objective was to study the effect of 3D surface roughness parameters on the contact temperature rise.

The results indicate a rise in maximum contact temperature with the increase in a number of 3D parameters, such as, average surface roughness Sa, ten‐point height parameter Sz, skewness of the surface height distribution Ssk, mean summit curvature Ssc, and developed interfacial area ratio parameter Sdr while temperature was found to decrease with increasing values of another set of parameters, such as, kurtosis of the 3D surface texture Sku, summit density of the surface Sds, surface bearing index Sbi, core fluid retention index Sci, valley fluid retention index Svi, and root mean square slope of the surface Sdq.

In any sliding system, with mixed or boundary lubricated conditions, it can be attempted to find the optimum value of the roughness parameters so that on suitable processing of the surfaces a lower contact temperature rise can be achieved.

No work has yet been reported on the effect of 3D roughness parameters on contact temperature.

The purpose of this paper is to explore the effect of surface roughness characterized by fractal geometry on squeeze film damping characteristics in damper of the linear rolling guide, which has not been studied so far.

The stochastic model of film thickness between rail and damper is established by using the two-variable Weierstrass–Mandelbrot function defining multi-scale and self-affinity properties of the rough surface topography. The stochastically averaged Reynolds equation is solved by using the variables separation method to further derive the film pressure distribution, the damping coefficient, the damping force and squeeze film time. The effect of surface roughness on squeeze film damping characteristics of the damper is analyzed and discussed through simulation.

By comparing cases of the rough surface for different fractal parameters and the smooth surface, it is shown that for the isotropic roughness structure, the presence of surface roughness of the damper decreases the squeeze film damping characteristics. It is found that roughness effect on the damping coefficient is associated with the film thickness. In addition, the vibration amplitude effect is negligible for the damper of the linear rolling guide.

To investigate the random surface roughness effect, the rough surface topography of damper of the linear rolling guide is characterized by using the fractal method instead of the traditional mathematical statistics method.

The present work is devoted to the numerical study of the stability of shallow jet. The effects of important parameters on the stability behavior for large scale shallow jets are considered and investigated. Connections between the stability theory and observed features reported in the literature are emphasized. The paper aims to discuss these issues.

A linear stability analysis of shallow jet incorporating the effects of bottom topography, bed friction and viscosity has been carried out by using the shallow water stability equation derived from the depth averaged shallow water equations in conjunction with both Chézy and Manning resistance formulae. Effects of the following main factors on the stability of shallow water jets are examined: Rossby number, bottom friction number, Reynolds number, topographic parameters, base velocity profile and resistance model. Special attention has been paid to the Coriolis effects on the jet stability by limiting the rotation number in the range of Ro∈[0, 1.0].

It is found that the Rossby number may either amplify or attenuate the growth of the flow instability depending on the values of the topographic parameters. There is a regime where the near cancellation of Coriolis effects due to other relevant parameters influences is responsible for enhancement of stability. The instability can be suppressed by the bottom friction when the bottom friction number is large enough. The amplification rate may become sensitive to the relatively small Reynolds number. The stability region using the Manning formula is larger than that using the Chézy formula. The combination of these effects may stabilize or destabilize the shallow jet flow. These results of the stability analysis are compared with those from the literature.

Results of linear stability analysis on shallow jets along roughness bottom bed are presented. Different from the previous studies, this paper includes the effects of bottom topography, Rossby number, Reynolds number, resistance formula and bed friction. It is found that the influence of Reynolds number on the stability of the jet is notable for relative small value. Therefore, it is important to experimental investigators that the viscosity should be considered with comparison to the results from inviscid assumption. In contrast with the classical analysis, the use of multi-parameters of the base velocity and topographic profile gives an extension to the jet stability analysis. To characterize the large scale motion, besides the bottom friction as proposed in the related literature, the Reynolds number Re, Rossby number Ro, the topographic parameters and parameters controlling base velocity profile may also be important to the stability analysis of shallow jet flows.

During running-in, the change in the honed cylinder liner surface alters the performance and efficiency of the piston ring-pack system. The present paper, thus, aims to investigate the surface topography and wear and friction evolution of a cylinder liner surface during the running-in tests on a reciprocating ring–liner tribometer under a mixed lubrication regime. After an initial period of rapid wear termed “running-in wear”, a relatively long-term steady-state surface topography can emerge. A numerical model is developed to predict the frictional performance of a piston ring-pack system at the initial and steady-state stages.

The liner surfaces are produced by slide honing (SH) and plateau honing (PH). The bearing area parameter (Rk family), commonly used in the automotive industry, is used to quantitatively characterize the surface topography change during the running-in process. A wear volume-sensitive surface roughness parameter, Rktot, is used to show the wear evolution.

The experimental results show that a slide-honed surface leads to reduced wear, and it reduces the costly running-in period compared to the plateau-honed surface. The simulation results show that running-in is a beneficial wear process that leads to a reduced friction mean effective pressure at the steady-state.

To simulate the mixed lubrication performance of a ring–liner system with non-Gaussian roughness, a one-dimensional homogenized mixed lubrication model was established. The real surface topography instead of its statistical properties is taken into account.