Search results

Recycled concrete is an economical and environmentally friendly green material. The shear performance of recycled concrete load-bearing masonry is studied, which is great of significance for its promotion and application and also has great significance for the sustainable development of energy materials.

In total, 30 new load-bearing block masonry samples of self-insulating recycled concrete are subjected to pure shear tests, and 42 samples are tested subjected to shear-compression composite shear tests. According to the axial design compression ratio, the test is separated into seven working conditions (0.1–0.8).

According to the test results, the recommended formula for the average shear strength along the joint section of recycled concrete block masonry is given, which can be used as a reference for engineering design. The measured shear-compression correlation curves of recycled concrete block masonry are drawn, and the proposed limits of three shear-compression failure characteristics are given. The recommended formula for the average shear strength of masonry under the theory of shear-friction with variable friction coefficient is given, providing a valuable reference for the formulation of relevant specifications and practical engineering design.

Simulated elastoplastic analysis and finite element modeling on the specimens are performed to verify the test results.

The majority of previous studies made on Recycled Concrete Aggregates (RCA) are limited to the utilisation of non-structural grade concrete due to unfavourable physical characteristics of RCA including the higher absorption of water, tending to increased water requirement of concrete. This seriously limits its applicability and as a result it reduces the usage of RCA in structural members. In the present study, the impact of hybrid fibres on cracking behaviour of RCA concrete beams along with the inclusion of reinforcing steel bars under two-point loading system exposed to different sustained elevated temperatures are being investigated.

RCA is substituted for Natural Coarse Aggregates (NCA) at 0, 50 and 100 percentages. The study involves testing of 150 mm cubes and beams of size (700 × 150 × 150) mm, i.e. with steel reinforcing bars along with the addition of 0.35% Steel fibres+ 0.15% polypropylene fibres. The specimens are being exposed to temperatures from 100° to 500°C with 100° interval for 2 h. Studies were made on the post crack analysis, which includes the measurement of crack width, crack length and load at first crack. The crack patterns were analysed in order to understand the effect of fibres and RCA at sustained elevated temperatures.

The result shows that ultimate load carrying capacity of reinforced concrete beams and load at first crack decreases with the raise in temperatures and increased percentage of RCA content in the mix. Further that 100% RCA replacement specimens showed lesser cracks when compared to the other mixes and the inclusion of fibres enhances the flexural capacity of members highlighting the importance of fibres.

RCA can be used for structural purposes and the study can be projected for assessing the performance of real structures with the extent of fire damage when recycled aggregates are used.

Most of recycled materials can be used in the regular concrete which solves two problems namely avoiding the dumping of C&D waste and preventing the usage of natural aggregates. Hence the study provides sustainable option for the production of concrete.

The reduction in capacity of flexural members due to the utilisation of recycled aggregates can be negated by the usage of fibres. Hence improved flexural performance is observed for specimens with fibres at sustained elevated temperatures.

This paper aims to investigate the experimental behavior and the reliability of concrete columns repaired using fiber-reinforced polymers (FRPs) under axial compression loading. The expression of the ultimate axial resistance was assessed from the experimental data of damaged concrete cylinders repaired by externally bonded double-FRP spiral strips.

The tested columns bearing capacity mainly depends of the elasticity modulus of both damaged and undamaged concrete have been considered in addition to the applied load and the cylinder diameter as random variables in the expression of the failure criterion. The reliability indicators were assessed using first order second moment method.

The emphasized test results, statistically fitted show that the strength has been retrofitted for all repaired specimens whatever the degree of initial damage. However, the gain in axial strength is inversely proportional to the degree of damage.

The efficiency of a new FRP repair procedure using double-spiral strips was studied. This research provides a technical and economical solution for retrofitting existing concrete columns. Finally, the random character of the variables that govern the studied system shows the accuracy and safety of the proposed original design.

The purpose of this study to investigate the organized porous network zinc (OPNZ) scaffolds. Their mechanical characteristics, surface roughness and fracture mechanism were assessed in relation to their structural properties. The prospects of fused deposition modeling (FDM) for printing metal scaffolds via rapid tooling have also been studied.

Zn scaffolds with different pore and strut sizes were manufactured via the rapid tooling method. This method is a multistep process that begins with the 3D printing of a polymer template. Later, a paraffin template was obtained from the prepared polymer template. Finally, this paraffin template was used to fabricate the Zn scaffold using microwave sintering. The characterization of prepared Zn samples involved structural characterization, microstructural study, surface roughness testing and compression testing. Moreover, based on the Gibson–Ashby model analysis, the model equations’ constant values were evaluated, which can help in predicting the mechanical properties of Zn scaffolds.

The scanning electron microscopy study confirmed that the fabricated sample pores were open and interconnected. The X-ray diffraction analysis revealed that the Zn scaffold contained hexagonal closed-packed Zn peaks related to the a-Zn phase, validating that scaffolds were free from contamination and impurity. The range for ultimate compressive strength, compressive modulus and plateau stresses for Zn samples were found to be 6.75–39 MPa, 0.14–3.51 GPa and 1.85–12.6 MPa by adjusting their porosity, which are comparable with the cancellous bones. The average roughness value for the Zn scaffolds was found to be 1.86 µm.

This research work can widen the scope for extrusion-based FDM printers for fabricating biocompatible and biodegradable metal Zn scaffolds. This study also revealed the effects of scaffold structural properties like porosity, pore and strut size effect on their mechanical characteristics in view of tissue engineering applications.

This study aims to enhance the understanding of fiber-reinforced polymer (FRP) applications in partially confined concrete, with a specific focus on improving economic value and load-bearing capacity. The research addresses the need for a more comprehensive analysis of non-uniform vertical strain responses and precise stress–strain models for FRP partially confined concrete.

DIC and strain gauges were employed to gather data during axial compression tests on FRP partially confined concrete specimens. Finite element analysis using ABAQUS was utilized to model partial confinement concrete with various constraint area ratios, ranging from 0 to 1. Experimental findings and simulation results were compared to refine and validate the stress–strain model.

The experimental results revealed that specimens exhibited strain responses characterized by either hardening or softening in both vertical and horizontal directions. The finite element analysis accurately reflected the relationship between surface constraint forces and axial strains in the x, y and z axes under different constraint area ratios. A proposed stress–strain model demonstrated high predictive accuracy for FRP partially confined concrete columns.

The stress–strain curves of partially confined concrete, based on Teng's foundation model for fully confined stress–strain behavior, exhibit a high level of predictive accuracy. These findings enhance the understanding of the mechanical behavior of partially confined concrete specimens, which is crucial for designing and assessing FRP confined concrete structures.

This research introduces innovative insights into the superior convenience and efficiency of partial wrapping strategies in the rehabilitation of beam-column joints, surpassing traditional full confinement methods. The study contributes methodological innovation by refining stress–strain models specifically for partially confined concrete, addressing the limitations of existing models. The combination of experimental and simulated assessments using DIC and FEM technologies provides robust empirical evidence, advancing the understanding and optimization of FRP-concrete structure performance. This work holds significance for the broader field of concrete structure reinforcement.

Existing deterministic models that predict the capacity of corroded reinforced concrete (RC) beams have limited applicability because they were based on accelerated tests that induce general corrosion. This research gap was addressed by performing a combined numerical and statistical analysis on RC beams, subjected to natural corrosion, to achieve a much better forecast.

Data of 42 naturally corroded beams were collected from the literature and analyzed numerically. Four constitutive models and their combinations were considered: the elastic-semi-plastic and elastic-perfectly-plastic models for steel, and two tensile models for concrete with and without the post-cracking stresses. Meanwhile, Popovics’ model was used to describe the behavior of concrete under compression. Corrosion coefficients were developed as functions of corrosion degree and beam parameters through linear regression analysis to fit the theoretical moment capacities with test data. The performance of the coefficients derived from different combinations of constitutive laws was then compared and validated.

The results showed that the highest accuracy (R² = 0.90) was achieved when the tensile response of concrete was modeled without the residual stresses after cracking and the steel was analyzed as an elastic-perfectly-plastic material. The proposed procedure and regression model also showed reasonable agreement with experimental data, even performing better than the current models derived from accelerated tests and traditional procedures.

This study presents a simple but reliable approach for quantifying the capacity of RC beams under more realistic conditions than previously reported. This method is simple and requires only a few variables to be employed. Civil engineers can use it to obtain a quick and rough estimate of the structural condition of corroding RC beams.

The purpose of this study is to develop the performance model of buildings designed by the seismic code 2800 against the explosion wave and determination of safety distance.

Analytical models of three-, five- and ten story structures that used moment frame system and also a ten-storey building with shaer wall designed based on the seismic code 2800 in term of design and nonlinear analysis were generated for use with Perform-3D software. Extensive parametric analysis is executed on different explosive loads with 100, 500, 1,000 and 5,000 Trinitrotoluene, soil types 2 and 3, models eqs and eqbs, the number of story buildings and the effect of shear wall to determine the safety distance based on collapse threshold performance (CP) level criterion.

The results indicate that by increasing the explosives mass from 100 to 5,000 kg and the number of the stories three and five induce increasing the safety distance of CP level in buildings to 4.5 meter and 3 meter times, respectively. Ten-story structures modeled on shear wall show very good performance because of stiffness rising and high energy absorption. In addition, by increasing the stories from five to ten, the amount of the safety distance reduces the CP level to 3.9 meter times.

The results of this work are meaningful for explosion-resistant design and damage assessments of reinforced concrete moment framed structures subjected to explosive explosion.

This study aims to explore the potential benefits favoring the adaptation of structural optimization techniques in the additive manufacturing (AM) of medical utilities to meet the repetitive demand for functionally precise customized orthoses. Irregularities encountered during the conventional treatment of tendon injuries can be eschewed using advanced structural simulation in design and innovative splint fabrication using 3D printing.

A customized mallet finger splint designed from 3D scans was subjected to ANSYS topological simulation comprising multi-level weight reduction to retain optimal mass (100%, 90%, 80%, 70% and 60%). A batch of the four typical 3D printing materials was chosen to conduct a comparative mechanical and thermal stress analysis, facilitating the selection of the optimal one for fabricating functionally adaptive splints. Assurance of structural safety was accomplished through the experimental validation of simulation results against the testing data set of ASTM D695 and ASTM D638 Type-1 specimens over a universal testing machine (UTM). Fused deposition modeling (FDM) 3D printing processed the optimized splint fabrication to assist evaluation of weight reduction percentage, fitting aesthetics, appearance, comfort, practicality and ventilation ease at the user end.

AM efficacy can efficiently execute the design complexity involved in the topology optimization (TO) results and introduces rehabilitation practicality into the application. Topologically optimized splint provided with favorable comfort, stiffness and strengthening features, offers ventilation ease and structural stability for customized appliances, with 30.52% lighter weight and 121.37% faster heat dissipation than unoptimized one.

The state of art multidisciplinary optimization featured with structural and material optimization attributes can deliberately meet medical necessity for performance-oriented orthotic devices.

The selective laser melting (SLM) technique, as a typical additive manufacturing process, is widely used for the fabrication of metallic biomedical components. In terms of biodegradability, zinc and its alloys represent an emerging generation of metallic materials for biomedical implants. The purpose of this paper is to obtain the Zn and Zn10Mg alloys with high mechanical properties using the SLM technology. The relationship between the processing parameters and the porosity of pure Zn and Zn10Mg alloy samples was investigated.

The samples were fabricated using SLM technology working in an inert gas closed chamber. Preliminary experiments were conducted to analyze the laser power and gas flow on evaporation, single track form and porosity. To evaluate the influence of factors on relative density, the response surface methodology was applied.

The satisfactory results of the proposed method were achieved, in which the relative density of the components reached up to 99.63%, and compression strength reached 214 ± 13 MPa under optimal processing conditions.

Zinc is categorized by its low melting and boiling point, which leads to the high porosity of the components. It is difficult to prepare the Zn alloy samples with high relative density using SLM technology. This work successfully achieved dense Zn and Zn10Mg samples and investigated their microstructure, mechanical properties and corrosion behavior.

The development of new advanced materials, such as photopolymerizable resins for use in stereolithography (SLA) and Ti6Al4V manufacture via selective laser melting (SLM) processes, have gained significant attention in recent years. Their accuracy, multi-material capability and application in novel fields, such as implantology, biomedical, aviation and energy industries, underscore the growing importance of these materials. The purpose of this study is oriented toward the application of new advanced materials in stent manufacturing realized by 3D printing technologies.

The methodology for designing personalized medical devices, implies computed tomography (CT) or magnetic resonance (MR) techniques. By realizing segmentation, reverse engineering and deriving a 3D model of a blood vessel, a subsequent stent design is achieved. The tessellation process and 3D printing methods can then be used to produce these parts. In this context, the SLA technology, in close correlation with the new types of developed resins, has brought significant evolution, as demonstrated through the analyses that are realized in the research presented in this study. This study undertakes a comprehensive approach, establishing experimentally the characteristics of two new types of photopolymerizable resins (both undoped and doped with micro-ceramic powders), remarking their great accuracy for 3D modeling in die-casting techniques, especially in the production process of customized stents.

A series of analyses were conducted, including scanning electron microscopy, energy-dispersive X-ray spectroscopy, mapping and roughness tests. Additionally, the structural integrity and molecular bonding of these resins were assessed by Fourier-transform infrared spectroscopy–attenuated total reflectance analysis. The research also explored the possibilities of using metallic alloys for producing the stents, comparing the direct manufacturing methods of stents’ struts by SLM technology using Ti6Al4V with stent models made from photopolymerizable resins using SLA. Furthermore, computer-aided engineering (CAE) simulations for two different stent struts were carried out, providing insights into the potential of using these materials and methods for realizing the production of stents.

This study covers advancements in materials and additive manufacturing methods but also approaches the use of CAE analysis, introducing in this way novel elements to the domain of customized stent manufacturing. The emerging applications of these resins, along with metallic alloys and 3D printing technologies, have brought significant contributions to the biomedical domain, as emphasized in this study. This study concludes by highlighting the current challenges and future research directions in the use of photopolymerizable resins and biocompatible metallic alloys, while also emphasizing the integration of artificial intelligence in the design process of customized stents by taking into consideration the 3D printing technologies that are used for producing these stents.