Search results

The purpose of this paper is to propose a method of qualitative ferrographic analysis by quantitative parameters of wear debris characteristics.

The amount of the wear debris needed for analysis on the ferrogram made by rotary ferrograph is discussed based on the theory of debris group. Quantitative parameters are constituted to express the characteristics of wear debris group, and correlation coefficients are employed to establish the relationship between wear debris and wear condition. The reliability of the method was verified by wear test experiments and ferrographic analysis.

The wear condition of machines should be determined by studying all the debris together as a group rather than by focusing on individual debris. In the proposed method, the qualitative analysis result is obtained by synthetic analysis of quantitative parameters of wear debris characteristics using a computer program, which makes the judgment of the wear system condition more objective and precise.

In the procedure of wear condition monitoring by the proposed method, because the weight factors and correlation coefficients introduced in this paper are determined according to the experiences deriving from practice among mining machinery, further rectifications may be needed if they are applied to other industrial field.

The paper illustrates a more objective and precise ferrographic analysis method for wear condition monitoring.

It is quite universal for high-speed turnouts to be exposed to the wear of the stock rail of the switch rail during the service process. The wear will cause the change of railhead profile and the relative positions of the switch rail and the stock rail, which will directly affect the wheel–rail contact state and wheel load transition when a train passes the turnout and will further impose serious impacts on the safety and stability of train operation. The purpose of this paper is to provide suggestions for wear management of high-speed turnout.

The actual wear characteristics of switch rails of high-speed turnouts in different guiding directions were studied based on the monitoring results on site; the authorized wear limits for the switch rails of high-speed turnout were studied through derailment risk analysis and switch rail strength analysis.

The results show that: the major factor for the service life of a curved switch rail is the lateral wear. The wear characteristics of the curved switch rail of a facing turnout are significantly different from those of a trailing turnout. To be specific, the lateral wear of the curved switch rail mainly occurs in the narrower section at its front end for a trailing turnout, but in the wider section at its rear end when for a facing turnout. The maximum lateral wear of a dismounted switch rail from a trailing turnout is found on the 15-mm wide section and is 3.9 mm, which does not reach the specified limit of 6 mm. For comparison, the lateral wear of a dismounted switch rail from a facing turnout is found from the 35-mm wide section to the full-width section and is greater than 7.5 mm, which exceeds the specified limit. Based on this, in addition to meeting the requirements of maintenance rules, the allowed wear of switch rails of high-speed turnout shall be so that the dangerous area with a tangent angle of wheel profile smaller than 43.6° will not contact the switch rail when the wheel is lifted by 2 mm. Accordingly, the lateral wear limit at the 5-mm wide section of the curved switch rail shall be reduced from 6 mm (as specified) to 3.5 mm.

The work in this paper is of reference significance to the research on the development law of rail wear in high-speed turnout area and the formulation of relevant standards.

The purpose of this paper is to find the influence of surface bump texture combination characteristics on friction-wear properties so as to provide a basis for the selection of the bump texture combination scheme on the surface of the roll.

In this paper, six groups of different bump texture combination characteristics and their processing methods are introduced, of which three groups are regular distribution with different spacing and three groups are random distribution with different spacing. Then the effect of bump textures with different spacing, regular and random distribution on friction-wear properties was studied by ring block friction-wear experiments.

The results show that the friction coefficient of random distribution texture surface is lower than that of regular texture surface under the same spacing condition. In the regular distribution, the friction coefficient decreases with the increase of texture spacing. In the random distribution, the friction coefficient increases at first and then decreases with the increase of texture spacing. In addition, the wear resistance of textured surface is significantly higher than that of smooth surface because of the higher microhardness of the textured area. The attenuation ratio of textured surface roughness decreases with the increase of the distance between adjacent textures.

At present, the research on roller surface friction-wear is mainly based on the change of the overall surface roughness. However, there are few reports on the influence of the combination characteristics of laser bump texture on friction-wear from the microscopic scale.

The cutting and extruding processing technology for ceramics based on the edge-chipping effect is a new contact removal machining method for hard, brittle materials such as engineering ceramics. This paper aims to provide an important reference to understand the tool wear mechanism and the wear law of this new processing technology.

The real-time temperature monitoring and the observation of micro-morphology are used to analyse the wear characteristics of the tool face. In addition, the research focuses on the influence of three processing parameters (axial feed rate, thickness of flange and depth of groove) on characteristics including tool wear.

The temperature variation shows that the new processing technology improves the tool temperatures condition. The tool is worn mainly by mechanical friction including abrasive wear, and the flank face also suffers the sustained scratching of residual materials on the rough machining surface. With increased feed rate, the wear of the rear face of the major flank initially decreased and then increased. As the depth of the retained flange increases, the wear became worse. The wear initially decreased and then increased with increasing depth of groove.

Study on the new processing technology is still in its early stages. Therefore, researchers are encouraged to test the proposed propositions further.

The machining process itself destroys materials, albeit a controllable manner: based on this principle, the authors proposed a new machining technology based on cracks driven by edge chipping. In this way, the surface of such ceramics is removed. Therefore, the research provides a new method for reducing processing costs and promoting the extensive application of engineering ceramic materials.

The cutting and extruding processing technology based on cracks driven by edge-chipping effect makes full use of the stress concentration effect caused by prefabricated defects, and the edge-chipping effect which occurs during machining-induced crack propagation. The wear mechanism and law of its tool is unique than other machining ways. This paper provides an important reference to understand the tool wear mechanism and the machining mechanism of this new processing technology. With the application of this study, the ceramics could be removed with less energy consumption and the tools with the hardness of lower than its own one. Therefore, it could not only reduce the processing costs but also promote the extensive applications of engineering ceramic materials.

In the process of conveying the solid–liquid two-phase medium of the centrifugal slurry pump, the wear of the flow-passing parts is an important problem affecting its life and safe operation. Therefore, a numerical investigation on the wear characteristics of the centrifugal slurry pump under different particle conditions was conducted.

A solid-liquid two-phase model based on CFD-DEM coupling is established and used to analyze the flow field and the wear characteristics of the flow-passing parts with different particle densities, volume fractions and sizes.

Particle conditions will affect the pump flow field. To analyze the pump wear characteristics, the wear distribution, wear value and cumulative force laws of flow-passing parts under different particle conditions are obtained. In each flow-passing part, with the increase of particle density, volume fraction and size, the wear area is concentrated and the wear depth increases. Under different particle conditions, the wear is mainly on the volute chamber and the blade pressure surface, and the tangential cumulative force of flow-passing parts is much larger than the normal cumulative force.

An accurate model and a coupled simulation method for predicting the wear of the slurry pump are obtained, and the wear characteristic law can provide a reference for the design of the slurry pump to reduce friction.

The wear of an abrasive single-crystal diamond (SCD) grit affects the machining quality of the sapphire wafer. This paper aims to investigate the influence of crystallographic orientation on the wear characteristics of SCD grit scratching on sapphire.

The wear characteristics of two SCD grits (SCD100 and SCD111) with different crystallographic orientations were systematically investigated. The wear mechanism involved in the scratching process was explored. The wear morphology, scratching forces and friction coefficient during the scratching process were measured and analyzed.

The experiment results show that the wear progress of the two SCD grits is obviously different. The wear resistance of SCD111 grit is greater than that of SCD100 grit in normal wear stage. However, the SCD100 grit could remove more sapphire material than SCD111 grit. The SCD grits mainly sustain extrusion stress and shear stress during scratching on sapphire. The crystallographic orientation of SCD grits plays a significant role in the wear progress during scratching on sapphire.

The results of the experimental studies could provide a theoretical foundation for improving the fabrication of abrasive diamond tools.

Since, wear is the one of the most commonly encountered industrial problems leading to frequent replacement of components there is a need to develop metal matrix composites (MMCs) for achieving better wear properties. The purpose of this paper is to fabricate aluminum MMCs to improve the dry sliding wear characteristics. An effective multi-response optimization approach called the principal component analysis (PCA) was used to identify the sets of optimal parameters in dry sliding wear process.

The present work investigates the dry sliding wear behavior of graphite reinforced aluminum composites produced by the molten metal mixing method by means of a pin-on-disc type wear set up. Dry sliding wear tests were carried on graphite reinforced MMCs and its matrix alloy sliding against a steel counter face. Different contact stress, reinforcement percentage, sliding distance and sliding velocity were selected as the control variables and the response selected was wear volume loss (WVL) and coefficient of friction (COF) to evaluate the dry sliding performance. An L25 orthogonal array was employed for the experimental design. Optimization of dry sliding performance of the graphite reinforced MMCs was performed using PCA.

Based on the PCA, the optimum level parameters for overall principal component (PC) of WVL and COF have been identified. Moreover, analysis of variance was performed to know the impact of individual factors on overall PC of WVL and COF. The results indicated that the reinforcement percentage was found to be most effective factor among the other control parameters on dry sliding wear followed by sliding distance, sliding velocity and contact stress. Finally the wear surface morphology of the composites has been investigated using scanning electron microscopy.

Various manufacturing techniques are available for processing of MMCs. Each technique has its own advantages and disadvantages. In particular, some techniques are significantly expensive compared to others. Generally the manufacturer prefers the low cost technique. Therefore stir casting technique which was used in this paper for manufacturing of Aluminum MMCs is the best alternative for processing of MMCs in the present commercial sectors. Since the most important criteria of a dry sliding wear behavior is to provide lower WVL and COF, this study has intended to prove the application of PCA technique for solving multi objective optimization problem in wear applications like piston rings, piston rods, cylinder heads and brake rotors, etc.

Application of multi-response optimization technique for evaluation of tribological characteristics for Aluminum MMCs made up of graphite particulates is a first-of-its-kind approach in literature. Hence PCA method can be successfully used for multi-response optimization of dry sliding wear process.

The purpose of this study is to distinguish the difference in tribological behavior of functionally graded composites in two sliding modes, namely, unidirectional and reciprocating.

A356-(10 Wt.%)SiCp functionally graded composite material (FGM) was prepared by vertical centrifugal casting and then a comparison was made between the tribological characteristics using pin-on-disk and pin-on-reciprocating plate configurations under identical operating conditions (sliding distance (s): 350 m; load (W): 30 = W = 120 N, in steps of 30 N; and velocity (v): 0.2 = v = 1.2 m/s, in steps of 0.2 m/s). Two types of test pins were considered, namely, a test pin taken from the outer zone of the FGM with maximum particle concentration and a test pin taken from the inner zone of the FGM in a matrix-rich region.

The study revealed that, for the test pin taken from the outer zone of the FGM in the low-velocity range (0.2–0.4 m/s), the reciprocating wear of the friction pair was dominant, while unidirectional wear was dominant in the velocity range of 0.6–0.8 m/s for the entire load range investigated. However, when the velocity was increased from 1.0 to 1.2 m/s, conflicting nature of dominancy in the wear characteristics of the friction pair was observed, depending on the loading condition. In addition, the inner zone FGM pin underwent seizure in the reciprocating mode, whereas this phenomenon was not seen in the unidirectional mode.

Differences in wear and friction characteristics of FGM friction pairs in two different sliding modes were investigated over a wide range of operating parameters.

The objectives of this paper are to assess the sliding wear response of a zinc‐based alloy over a range of sliding speeds and pressures in oil‐lubricated condition with respect to a cast iron, to understand the role of different microconstituents in controlling the observed wear behaviour and to examine various operating material removal mechanisms.

Sliding wear tests have been carried out using a pin‐on‐disc machine in oil‐lubricated condition at different speeds and pressures. The wear response has been explained in terms of specific nature of various microconstituents of the specimen materials and substantiated through the characteristics of wear surfaces, subsurface regions and debris particles.

The wear rate increased with the sliding speed while load produced a mixed influence. Further, the friction coefficient and frictional heating were influenced by the test duration, load and speed in a mixed manner. Moreover, the zinc‐based alloy attained lower wear rate but higher friction coefficient than that of the cast iron while frictional heating followed a mixed trend.

The paper further establishes a zinc‐based alloy as a potential substitute material system to a well‐known cast iron in tribological applications and enables further understanding of the wear mechanisms.

The present paper assesses the sliding wear performance of a lighter zinc‐based alloy as an effective potential substitute material system to cast iron in tribological applications. An attempt has also been made to understand the role played by different microconstituents in controlling the wear behavior and substantiate the wear response through the characteristics of wear surfaces, subsurface regions and debris.

This paper aims to clarify the friction properties of 304 steel surface modification. The surface modification includes laser texturing processing and nitriding treatment on 304 steel surface, and then the friction properties’ test was conducted on different friction directions and different upper test samples by using microfriction and wear testing machine.

The diameter and spacing of 100-, 150-, 200-, 300-μm pit array on the surface of 304 steel were calculated using a M-DPSS-50 semiconductor laser device. Then, the textured surface was nitriding-treated using a nitriding salt bath device. The chemical composition, surface morphology and surface microhardness of the composite-modified surface were measured by X-ray diffraction and by using an optical microscope and a microhardness tester. The tribological characteristics of the composite-modified surface were tested by MRTR microcomputer-controlled multifunctional friction and wear testing machine.

The result showed that a rule pit texture surface was obtained by the texture processing. The microhardness of nitriding treatment surface reached 574.27HV0.1, which significantly higher than 222.58HV0.1 of 304 steel. The composite-modified surface has excellent anti-friction and wear resistance properties when the upper specimen was GCr15 steel and ZrO2, respectively. The composite-modified surface has excellent anti-friction and anti-wear properties after long time friction under different angles. However, the friction coefficient and wear morphology of the friction pairs are not affected by the friction angle.

Because of the chosen research approach, the research results may lack generalizability. Therefore, researchers are encouraged to test the proposed propositions further.

The paper conducted a systematic study of the tribological characteristics of 304 steel composite modification surface and provided a good basis for the extensive application of 304 steel.

The study provides a good basis for the extensive application of 304 steel.

This paper fulfils an identified need to study the extensive application of 304 steel.