Search results

The purpose of the study is to propose a novel implementation of twisted tape in sinusoidal wavy-walled tubes to enhance the rate of heat transfer without compromising thermal efficiency. The study numerically investigates the fluid flow characteristics and analyzes the effect of different geometrical configurations, including wall wave amplitude, tape twist angles and nanoparticle volume fractions, on heat transfer improvement and performance factor.

This problem is numerically investigated using computational fluid dynamics, and the method is the finite volume method. A two-phase mixture model is used for nanofluid modeling.

The study investigated the effect of wall waviness, twisted tape, and nanoparticles on forced convective heat transfer and friction factor behavior in laminar pipe flow in three different Reynolds number regimes. The results showed that implementing twisted tape in wavy tubes significantly increased the rate of heat transfer and the performance factor, with the best twist ratio between 90 and 180°. Adding nanoparticles also enhanced heat transfer and performance factor, but to a lesser extent than wavy wall-twisted tape combinations. The study suggests selecting a proper combination of wavy wall and twisted tape at each Reynolds number to achieve an optimum solution.

To the best of the authors’ knowledge, the implementation of the selected passive methods in sinusoidal wavy tubes has not been studied before, and no previous studies have taken into account such a mix of heat transfer improvement techniques.

The purpose of this study is to investigate the mechanical properties of denim fabrics constructed from ring-spun and open-end rotor spun yarns.

Yarns of 10s Ne count using cotton fibers were spun using the ring and open-end rotor spinning technologies. The yarns were used to produce a denim fabric on an air-jet loom with a 3/1 twill weave structure. Mechanical tests – tensile strength, tear strength, abrasion resistance and pilling resistance – of denim fabrics were evaluated. The test results were analyzed using analysis of variance with the help of Software Package for Social Sciences.

Denim fabrics made by using ring-spun yarns exhibited better tensile and tear strength properties than denim fabrics made by using open-end rotor spun yarns. On the contrary, denim produced using open-end rotor yarns have better abrasion resistance, pilling resistance and air permeability than those produced using ring-spun yarns.

Both spinning techniques have a significant influence on the properties of denim fabrics. Whenever better tensile and tear strength is required, it is better to use ring-spun yarns, while if the requirement is better abrasion resistance and pilling resistance with high air permeability, then open-end rotor spun yarns shall be used.

In this paper, the brain potential changes caused by touching fabrics for handle evaluation were recorded by event related potential (ERP) method, compared with subjective evaluation scores and physical index of KES, explore the cognitive mechanism of the transformation of tactile sensation into neural impulses triggered by subtle mechanical stimuli such as material, texture, density and morphology in fabrics. By combining subjective evaluation of fabric tactile sensation, objective physical properties of fabrics and objective neurobiological signals, explore the neurophysiological mechanism of tactile cognition and the signal characteristics and time process of tactile information processing.

The ERP technology was first proposed by a British psychologist named Grey Walter. It is an imaging technique of noninvasive brain cognition, whose potential changes are related to the human physical and mental activities. ERP is different from electroencephalography (EEG) and evoked potentials (EP) on the fact that it cannot only record stimulated physical information which is transmitted to brain, but also response to the psychological activities which related to attention, identification, comparison, memory, judgment and cognition as well as to human’s neural physiological changes which are caused by cognitive process of the feeling by stimulation.

According to potential changes in the cerebral cortex evoked by touching four types of silk fabrics, human brain received the physical stimulation in the early stage (50 ms) of fabrics handle evaluation, and the P50 component amplitude showed negative correlation with fabric smoothness sensations. Around 200 ms after tactile stimulus onset, the amplitude of P200 component show positive correlation with the softness sensation of silk fabrics. The relationship between the amplitude of P300 and the sense of smoothness and softness need further evidence to proof.

In this paper, the brain potential changes caused by touching fabrics for handle evaluation were recorded by event related potential (ERP) method, compared with subjective evaluation scores and physical index of KES, the results shown that the maximum amplitude of P50 component evoked by fabric touching is related to the fabrics’ smoothness and roughness emotion, which means in the early stage processing of tactile sensation, the rougher fabrics could arouse more attention. In addition, the amplitude of P200 component shows positive correlation with the softness sensation of silk fabrics.

Eri silk fiber has superior thermal insulation behavior, better softness than cotton fiber. However, Eri silk’s use in the commercial arena has not yet taken off. The purpose of the study is to explore the comfort properties of the fabric, which enhances the commercial acceptance of Eri silk clothing.

In this investigation, three different single knit Eri silk structures were produced with different loop lengths and yarn counts to analyze the influence of process variables on low-stress mechanical properties. To execute the research work, Eri silk spun yarn of three different linear densities (15 tex, 20 tex, 25 tex) were chosen. Three different knitted structures were produced, such as single jersey, popcorn and cellular blister, and two different loop lengths were also selected.

The cellular blister structure has shown appreciable low-stress properties next highest position was attained by the popcorn structure. Yarn fineness and loop length were significant with most of the low-stress properties.

The findings of this research will contribute to a greater awareness of Eri silk knitted fabric and its process parameters in relation to its commercial utility.

This study was conducted to explore the influence of knit structure, loop length and yarn count on the low-stress properties of Eri silk-based thermal clothing.

Quadrotors have been applied in various fields. However, because the quadrotor is subject to multiple disturbances, consisting of external disturbances, actuator faults and parameter uncertainties, it is difficult to control the unmanned aerial vehicle (UAV) to achieve high-precision tracking performance. This paper aims to design a safety controller that uses observer and neural network method to improve the tracking performance of UAV under multiple disturbances. The experiments prove that this method is effective.

First, to actively estimate and compensate the synthetic uncertainties of the system, a finite-time extended state observer is investigated, and the disturbances are transformed into the extended state of the system for estimation. Second, an adaptive neural network controller that does not accurately require the dynamic model knowledge is designed based on the estimated value, where the weights of the neural network can be dynamically adjusted by the adaptive law. Furthermore, the finite-time bounded convergence of the proposed observer and the stability of the system are proved through homogeneous theory and Lyapunov method.

The figure-“8” climbing flight simulation and real flight experiments illustrate that the proposed safety control strategy has good tracking performance.

This paper proposes the safety control structure of the UAV, which combines the extended state observer with the neural network method. Numerical simulation results and actual flight experiments demonstrate the effectiveness of the proposed control strategy.

In the field of research on the application of digital printing to textile materials, there are still many research issues that arise from the very demanding interaction of digital printing technology and the complex, heterogeneous surface system of textile materials. This is precisely why the area of pre-treatment of textile materials is in need of research, and the purpose of this research was to establish the level of influence of physical and chemical activation of the textile surface with plasma and the possibility of improving the quality of the print and colour reproduction.

The paper deals with the possibility of applying argon and oxygen cold low-pressure plasma in the processing of cellulose knitted fabrics, with the aim of improving the quality of the print and colour reproduction in digital pigment inkjet printing. The selected raw material samples were 100% raw cotton and lyocell. After plasma treatment, the samples were printed by digital ink jet printing with water-based pigment printing ink. An analysis of the micromorphological structure of untreated and plasma-treated samples before and after printing was carried out, and a comparative analysis of the colour of the printed elements was carried out depending on the pre-treatment.

The conducted research showed a positive influence of plasma pre-treatment on the coverage of the fibre surface with pigments, the uniformity of pigment distribution along the fibre surface and the uniformity of the distribution of the polymeric binder layer. This has a positive effect on colour reproduction. Also, certain improvements in colourfastness to washing were obtained.

Considering the complexity of the topic, although exhaustive, this research is not sufficient in itself, but opens up new questions and gives ideas for further research that must be carried out in this area.

Also, this kind of research contributes to the possibility of adopting the idea of industrial plasma transformation, as an ecologically sustainable functionalisation of textiles, which has not yet been established.

This research is certainly a contribution to the establishment of acceptable textile pre-treatment methods in the field of digital printing, as one of the key quality factors in digital textile printing (DTP). Considering the still large number of obstacles and unanswered questions encountered in the field of digital printing on textiles, this kind of research is a strong contribution to the understanding of the fundamental mechanisms of the complex interaction between printing ink and textile.

The rapid growth of emerging market firms (EMFs) has been a topic of interest for the past two decades, especially in China. However, few studies have discussed how and why EMFs can impel the upgrading of their capabilities to quickly win competitive advantages in the global market. In this context, the purpose of this paper is to unravel the implausible upgrading phenomenon from the perspective of technological proximity.

This paper adopts a single case study, specifically that of a leading Chinese e-bike firm, with a special focus on the dynamic nature of the capability upgrading process and underlying mechanisms.

The results show that taking advantage of technological proximity is an important way for EMFs to climb the ladder of capability upgrading. The stage-based process reveals how capability upgrading is achieved through elaborate actions related to technological proximity. Furthermore, this study finds three learning mechanisms behind the technological proximity, which enable firms to successfully upgrade to higher levels of capabilities. In particular, the trigger role played by contextual conditions in guiding firms' capability upgrading is highlighted and characterized.

This study enriches traditional capability upgrading literature from a technological proximity perspective, especially the traditional static upgrading research related to EMFs. The authors also contribute to the conceptualization of technological proximity. However, the research setting is China's e-bike industry; therefore, the study's generalizability to other emerging markets and industries may be limited.

The results show that it is important to recognize the value of the transfer and sharing of technology between proximal industries for local governments. Also, appropriate policies should be developed to break down the technology barriers between these industries. Moreover, rather than catching up with the superior technologies of multinational corporations in advanced countries, focusing on products with high technological proximity in local or regional areas may be more helpful for EMFs' upgrading.

This paper investigates the capability upgrading process and mechanisms in EMFs, particularly with respect to the role played by technological proximity.

The purpose of this study is to advance turbulent thermal convection inside the constant heat-flux round tube inserted by multiple perforated twisted tapes.

The novel design of this study is accomplished by inserting several twisted tapes and drilling some circular perforations near the tape edge (C1, C3, C5: solid tapes; C2, C4, C6: perforated tapes). The turbulence flow appearances and thermal convective features are examined for various Reynolds numbers (8,000–14,000) using the renormalization group (RNG) κ−ε turbulent model and Semi-Implicit Method for Pressure-Linked Equations (SIMPLE) algorithm.

The simulated outcomes reveal that inserting more perforated-twisted tapes into the heated round tube promotes turbulent thermal convection effectively. A swirling flow caused by the twisted tapes to produce the secondary flow jets between two reverse-spin tapes can combine with the main flow passing through the perforations at the outer edge to enhance the vortex flow. The primary factors are the quantity of twisted tapes and with/without perforations, as the perforation ratio remains at 2.5 in this numerical work. Weighing friction along the tube, C6 (four reverse-spin perforated-twisted tapes) brings the uppermost thermal-hydraulic performance of 1.23 under Re = 8,000.

The constant thermo-hydraulic attributes of liquid water and the steady Newtonian fluid are research limitations for this simulated work.

The simulated outcomes will avail the inner-pipe design of a heat exchanger inserted by multiple perforated twisted tapes to enhance superior heat transfer.

These twisted tapes form tiny circular perforations along the tape edge to introduce the fluid flow through these bores and combine with the secondary flow induced between two reverse-spin tapes. This scheme enhances the swirling flow, turbulence intensity and fluid mixing to advance thermal convection since larger perforations cannot produce large jet velocity or the position of perforations is too far from the tape edge to generate a separated flow. Consequently, this work contributes a valuable cooling mechanism toward thermal engineering.

This paper aims to demonstrate that, in line with the emerging trend of multifunctional yarn development, cotton yarn can effectively harness renewable solar energy to achieve photothermal conversion and thermochromism. This innovation not only maintains the comfort associated with natural fiber cotton yarn but also enhances its ultraviolet (UV) light resistance.

In this work, 4% zirconium carbide (ZrC) and thermochromic powder were adhered to cotton yarn through polyurethane (PU) by sizing coating method. After sizing, the two cotton yarns are twisted by ring spinning to obtain composite yarns with photothermal conversion and thermochromic functions.

The yarn obtained by cotton/6%PU/8% thermochromic dye single yarn and cotton/6%PU/4% ZrC single yarn composite is the best match. After 5 min of infrared light, the temperature of the composite yarn rose to the maximum, increasing by 36.1°C. The ΔE* value before and after irradiation of infrared lamp is 26.565, which proves that the thermochromic function is good. The yarn dryness unevenness was significantly reduced by 27.2%. The composite yarn has a UPF value of up to 89.22, and its performance characteristics remain stable after 100 minutes of washing.

The composite yarn’s photothermal conversion and thermochromism functions are mutually reinforcing. Using sunlight can simultaneously achieve heating and discoloration effects without consuming additional energy. The cotton yarn used in this application is versatile, and suitable for a wide range of uses including clothing, temperature visualization detection and other scenarios.

The research focused on analysing a unique type of heat exchanger that uses swirling air flow over heated tubes. This heat exchanger includes a round baffle plate with holes and opposite-oriented trapezoidal air deflectors attached at different angles. The deflectors are spaced at various distances, and the tubes are arranged in a circular pattern while maintaining a constant heat flux.

This setup is housed inside a circular duct with airflow in the longitudinal direction. The study examined the impact of different inclination angles and pitch ratios on the performance of the heat exchanger within a specific range of Reynolds numbers.

The findings revealed that the angle of inclination significantly affected the flow velocity, with higher angles resulting in increased velocity. The heat transfer performance was best at lower inclination angles and pitch ratios. Flow resistance decreased with increasing angle of inclination and pitch ratio.

The average thermal enhancement factor decreased with higher inclination angles, with the maximum value observed as 0.94 at a pitch ratio of 1 at an angle of 30°.