Search results

This study aims to characterize the mechanical properties of sintered nano-silver under various sintering processes by nano-indentation tests.

Through microstructure observations and characterization, the influences of sintering process on the microstructure evolutions of sintered nano-silver were presented. And, the indentation load, indentation displacement curves of sintered silver under various sintering processes were measured by using nano-indentation test. Based on the nano-indentation test, a reverse analysis of the finite element calculation was used to determine the yielding stress and hardening exponent.

The porosity decreases with the increase of the sintering temperature, while the average particle size of sintered nano-silver increases with the increase of sintering temperature and sintering time. In addition, the porosity reduced from 34.88%, 30.52%, to 25.04% if the ramp rate was decreased from 25°C/min, 15°C/min, to 5°C/min, respectively. The particle size appears more frequently within 1 µm and 2 µm under the lower ramp rate. With reverse analysis, the strain hardening exponent gradually heightened with the increase of temperature, while the yielding stress value decreased significantly with the increase of temperature. When the sintering time increased, the strain hardening exponent increased slightly.

The mechanical properties of sintered nano-silver under different sintering processes are clearly understood.

This paper could provide a novel perspective on understanding the sintering process effects on the mechanical properties of sintered nano-silver.

Selective laser sintering (SLS) is an essential technology in the field of additive manufacturing. However, SLS technology is limited by the traditional point-laser sintering method and has reached the bottleneck of efficiency improvement. This study aims to develop an image-shaped laser sintering (ISLS) system based on a digital micromirror device (DMD) to address this problem. The ISLS system uses an image-shaped laser light source with a size of 16 mm × 25.6 mm instead of the traditional SLS point-laser light source.

The ISLS system achieves large-area image-shaped sintering of polymer powder materials by moving the laser light source continuously in the x-direction and updating the sintering pattern synchronously, as well as by overlapping the splicing of adjacent sintering areas in the y-direction. A low-cost composite powder suitable for the ISLS system was prepared using polyether sulfone (PES), pinewood and carbon black (CB) powders as raw materials. Large-sized samples were fabricated using composite powder, and the microstructure, dimensional accuracy, geometric deviation, density, mechanical properties and feasible feature sizes were evaluated.

The experimental results demonstrate that the ISLS system is feasible and can print large-sized parts with good dimensional accuracy, acceptable geometric deviations, specific small-scale features and certain density and mechanical properties.

This study has achieved the transition from traditional point sintering mode to image-shaped surface sintering mode. It has provided a new approach to enhance the system performance of traditional SLS.

The purpose of this study is to investigate the effect of the sintering temperature on the microstructural, mechanical and physical properties of Cu-SiC composites.

The powder metallurgy route was used to fabricate the samples. Cold compaction of powders was conducted at 250 MPa which was followed by sintering at 850°C–950°C at the interval of 50 °C in the open atmospheric furnace. SiC was used as a reinforcement and the volumetric fraction of the SiC was varied as 10%, 15% and 20%. The processed samples were metallurgically characterized by the scanning electron microscope (SEM). Mechanical characterization was done using tensile and Vickers’ micro-hardness testing to check the hardness and strength of the samples. Archimedes principle and Four-point collinear probe method were used to measure the density and electrical resistivity of the samples.

SEM micrograph reveals the uniform dispersion of the SiC particles in the Cu matrix element. The results revealed that the Hardness and tensile strength were improved due to the addition of SiC and were maximum for the samples sintered at 950 °C. The addition of SiC has also increased the electrical resistivity of the Cu-SiC composite and was lowest for Cu 100% while the relative density has shown the reverse trend. Further, it was found that the maximum hardness of 91.67 Hv and ultimate tensile strength of 312.93 MPa were found for Cu-20% SiC composite and the lowest electrical resistivity of 2.017 µ- Ω-cm was found for pure Cu sample sintered at 950 °C, and this temperature was concluded as the optimum sintering temperature.

The powder metallurgy route for the fabrication of the composites is a challenging task as the trapping of oxygen cannot be controlled during the compaction process as well as during the sintering process. So, a more intensive study is required to overcome these kinds of limitations.

As of the author’s best knowledge, no work has been reported on the effect of sintering temperature on the properties of the Cu-SiC composites which has huge potential in the industries.

The consolidation process and morphology evolution in ceramics-based additive manufacturing (AM) are still not well-understood. As a way to better understand the ceramic selective laser sintering (SLS), a dynamic three-dimensional computational model was developed to forecast thermal behavior of hydroxyapatite (HA) bioceramic.

AM has revolutionized automotive, biomedical and aerospace industries, among many others. AM provides design and geometric freedom, rapid product customization and manufacturing flexibility through its layer-by-layer technique. However, a very limited number of materials are printable because of rapid melting and solidification hysteresis. Melting-solidification dynamics in powder bed fusion are usually correlated with welding, often ignoring the intrinsic properties of the laser irradiation; unsurprisingly, the printable materials are mostly the well-known weldable materials.

The consolidation mechanism of HA was identified during its processing in a ceramic SLS device, then the effect of the laser energy density was studied to see how it affects the processing window. Premature sintering and sintering regimes were revealed and elaborated in detail. The full consolidation beyond sintering was also revealed along with its interaction to baseplate.

These findings provide important insight into the consolidation mechanism of HA ceramics, which will be the cornerstone for extending the range of materials in laser powder bed fusion of ceramics.

This study aims to investigate the performance of filament-based material extrusion additive manufacturing (MEX), combined with debinding and sintering, as a novel approach to manufacturing ceramic components.

A commercial ZrO₂ filament was selected and analysed by infra-red (IR) spectroscopy, rheology and thermo-gravimetry. The influence of the print parameters (layer thickness, flow rate multiplier, printing speed) and sintering cycle were investigated to define a suitable printing and sintering strategy. Biaxial flexure tests were applied on sintered discs realised with optimised printing strategies, and the results were analysed via Weibull statistics to evaluate the mechanical properties of printed components. The hardness and thermal conductivity of sintered components were also tested.

Layer thickness and flow rate multiplier of the printing process were proved to have significant effect on the density of as-printed parts. Optimised samples display a sintered density >99% of the theoretical density, 20% linear sintering shrinkage, a characteristic flexural strength of 871 MPa with a Weibull modulus of 4.9, a Vickers hardness of 12.90 ± 0.3 GPa and a thermal conductivity of 3.62 W/mK. Gyroids were printed for demonstration purposes.

To the best of the authors’ knowledge, this work is the first to apply biaxial flexure tests and Weibull statistics to additively manufactured MEX zirconia components, hence providing comparable results to other additive technologies. Moreover, fractography analysis builds the connection between printing defects and the fracture mechanism of bending. This study also provides guidelines for fabricating high-density zirconia components with MEX.

With the technological progress, high-performance materials are emerging in the market of additive manufacturing to comply with the advanced requirements demanded for technical applications. In selective laser sintering (SLS), innovative powder materials integrating conductive reinforcements are attracting much interest within academic and industrial communities as promising alternatives to common engineering thermoplastics. However, the practical implementation of functional materials is limited by the extensive list of conditions required for a successful laser-sintering process, related to the morphology, powder size and shape, heat resistance, melt viscosity and others. The purpose of this study is to explore composite materials of polyamide 12 (PA12) incorporating multi-walled carbon nanotubes (MWCNT) and graphene nanoplatelets (GNP), aiming to understand their suitability for advanced SLS applications.

PA12-MWCNT and PA12-GNP materials were blended through a pre-optimized process of mechanical mixing with various percentages of reinforcement between 0.50 wt.% and 3.00 wt.% and processed by SLS with appropriate volume energy density. Several test specimens were produced and characterized with regard to processability, thermal, mechanical, electrical and morphological properties. Finally, a comparative analysis of the performance of both carbon-based materials was performed.

The results of this research demonstrated easier processability and higher tensile strength and impact resistance for composites incorporating MWCNT but higher tensile elastic modulus, compressive strength and microstructural homogeneity for GNP-based materials. Despite the decrease in mechanical properties, valuable results of electrical conductivity were obtained with both carbon solutions until 10^–6 S/cm.

The carbon-based composites developed in this research allow for the expansion of the applicability of laser-sintered parts to advanced fields, including electronics-related industries that require functional materials capable of protecting sensitive devices against electrostatic discharge.

The purpose of this study to investigate the organized porous network zinc (OPNZ) scaffolds. Their mechanical characteristics, surface roughness and fracture mechanism were assessed in relation to their structural properties. The prospects of fused deposition modeling (FDM) for printing metal scaffolds via rapid tooling have also been studied.

Zn scaffolds with different pore and strut sizes were manufactured via the rapid tooling method. This method is a multistep process that begins with the 3D printing of a polymer template. Later, a paraffin template was obtained from the prepared polymer template. Finally, this paraffin template was used to fabricate the Zn scaffold using microwave sintering. The characterization of prepared Zn samples involved structural characterization, microstructural study, surface roughness testing and compression testing. Moreover, based on the Gibson–Ashby model analysis, the model equations’ constant values were evaluated, which can help in predicting the mechanical properties of Zn scaffolds.

The scanning electron microscopy study confirmed that the fabricated sample pores were open and interconnected. The X-ray diffraction analysis revealed that the Zn scaffold contained hexagonal closed-packed Zn peaks related to the a-Zn phase, validating that scaffolds were free from contamination and impurity. The range for ultimate compressive strength, compressive modulus and plateau stresses for Zn samples were found to be 6.75–39 MPa, 0.14–3.51 GPa and 1.85–12.6 MPa by adjusting their porosity, which are comparable with the cancellous bones. The average roughness value for the Zn scaffolds was found to be 1.86 µm.

This research work can widen the scope for extrusion-based FDM printers for fabricating biocompatible and biodegradable metal Zn scaffolds. This study also revealed the effects of scaffold structural properties like porosity, pore and strut size effect on their mechanical characteristics in view of tissue engineering applications.

Additive manufacturing (AM) has been one of the most highlighted processes of the last few years. AM prints complex parts and items from 3D files regarding different materials, such as polymers. Moreover, there are different AM techniques available for polymers, such as selective laser sintering. In the SLS technology, polyamides 11 and 12 lead 88% of the market. These materials are high-cost and use an average of 50% of virgin material at each printing. It is possible to use lower rates of virgin material, but at least 30% is recommended. Low rates of virgin material decrease mechanical properties.

This study aims to evaluate the influence on the mechanical properties of the percentage of reused PA12 in parts manufactured by the SLS process. The specimens of PA12 were manufactured with a percentage of virgin/reused polymer of 50/50, 40/60, 30/70, 20/80 and 10/90. We considered three distinct printing directions to compare the mechanical properties of the specimens: horizontal, perpendicular and vertical.

The results showed that when the percentage of reused material increases, the tensile strength limit (TSL), flexural strength limit and Shore D hardness decrease. Another aspect visualized was the fragile behavior presented in the vertical specimens. In addition, DSC analysis indicated a 2% reduction of crystallinity. Scanning electron microscopy images revealed spherical voids and unfused particles of PA12 at the fracture of tensile test specimens. The material thermal history and unfused particles could decrease the material properties.

We observed that the mechanical properties, such as the TSL, flexural strength limit and hardness, decrease as the percentage of reused material increases. In addition, the process presented a printing-direction dependence, where the vertical direction presented as the more brittle between the ones used.

This study aims to enhance merging of additive manufacturing (AM) techniques with powder injection molding (PIM). In this way, the prototypes could be 3D-printed and mass production implemented using PIM. Thus, the surface properties and mechanical performance of parts produced using powder/polymer binder feedstocks [material extrusion (MEX) and PIM] were investigated and compared with powder manufacturing based on direct metal laser sintering (DMLS).

PIM parts were manufactured from 17-4PH stainless steel PIM-quality powder and powder intended for powder bed fusion compounded with a recently developed environmentally benign binder. Rheological data obtained at the relevant temperatures were used to set up the process parameters of injection molding. The tensile and yield strengths as well as the strain at break were determined for PIM sintered parts and compared to those produced using MEX and DMLS. Surface properties were evaluated through a 3D scanner and analyzed with advanced statistical tools.

Advanced statistical analyses of the surface properties showed the proximity between the surfaces created via PIM and MEX. The tensile and yield strengths, as well as the strain at break, suggested that DMLS provides sintered samples with the highest strength and ductility; however, PIM parts made from environmentally benign feedstock may successfully compete with this manufacturing route.

This study addresses the issues connected to the merging of two environmentally efficient processing routes. The literature survey included has shown that there is so far no study comparing AM and PIM techniques systematically on the fixed part shape and dimensions using advanced statistical tools to derive the proximity of the investigated processing routes.

The purpose of this study is to investigate the effects of graphene nanoplates (GNPs), and alloying time on aluminum matrix composite. After mixing the powdered materials in the alloying device, solid samples were formed by sintering. It is thought that the effect of using such a mechanical mixer on GNPs will be investigated and this study will give a perspective on the composites that GNPs will make with Al and its alloys.

Mechanical alloying (MA) device capable of high-speed shaking (Spex) movement was used and alloying was performed by adding other metal powders into aluminum, which is the matrix material, with the addition of GNPs at three different rates and times. The crystal size and lattice stress parameters were calculated by obtaining the X-ray diffraction (XRD) graphics of the obtained powder mixtures.

The XRD graphs of the obtained powder mixtures showed that the Al peaks decreased when the MA time increased. When the scanning electron microscopy images of the powder mixtures were examined, it was observed that agglomeration occurred especially in 1 and 1.5 Wt.% graphene reinforced mixtures that were MA for 90 min. The increase in the amount of graphene had a negative effect on the homogeneous distribution. When the Vickers microhardness values of the samples were examined, the hardness value of all samples increased up to the MA time of 45 min, and decreased in the times over 45 min.

The use of GNPs in the mechanical alloying technique and the fact that this technique was performed on the Retsch MM 400 device, which is a Spex type mixer, shows the originality of the study in terms of time and material content.