Search results

Liquid-assisted laser surface texturing technology was used to create composite microtextures on triangular guide rail surfaces to enhance their tribological properties.

Numerical simulations were used to investigate the impact of various microtextures on fluid dynamic lubrication. Reciprocating friction and wear tests, followed by mechanistic analysis, examined the combined tribological effects of microtextured surfaces and lubricants.

The numerical simulation outcomes reveal a significant augmentation in the influence of fluid dynamic pressure due to composite microtextures, consequently amplifying the load-bearing capacity of the oil film. The average friction coefficient of composite microtextured samples was approximately 0.136 in reciprocating pin-on-disk friction tests, representing approximately 17% decrease compared to polished samples. Triangular guide rails with composite microtextures demonstrated the lowest average coefficient under conditions of high-speed and heavy-loading in the reciprocating friction and wear tests. Additionally, the presence of composite microtextures was found to promote the formation of adsorbed and friction films during friction, potentially contributing to the enhancement of tribological properties.

Triangular guide rails face high friction and wear, limiting their stability in demanding applications like machine tool guideways. This paper proposes a novel approach for steel triangular guide rails, involving composite microtexturing, numerical fluid simulations, liquid-assisted laser surface texturing and friction-wear testing. By implementing composite microtextures, the method aims to reduce friction coefficients and extend guideway service life, thereby saving energy and reducing maintenance costs. Enhancing the antifriction and antiwear properties of machine tool guideways is crucial for improving performance and longevity.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2024-0183/

This paper aims to enhance lubrication performance of the pitcher plant–like textured surface with various parameters.

A pitcher plant–like structure surface is fabricated on the copper alloy, and the lubrication performance of the pitcher plant–like structure with various parameters is evaluated. In addition, the pressure distribution and oil film load capacity of the pitcher plant–like surface are simulated based on Navier–Stokes equations.

When the direction of motion aligns with the pitcher plant–like structure, the friction coefficient remains lower than that of the nontextured surface, and it exhibits a decreasing trend with the increasing of the texture width and spacing distance; the lowest friction coefficient (0.04) is achieved with B = 0.3 mm, L = 1.0 mm and θ = 45°, marking a 75% reduction compared to the nontextured surface. Simulation results demonstrate that with the increase in texture width and spacing distance, the oil film load-bearing capacity demonstrates an increasing trend.

Bionic pitcher plants are prepared on the copper alloy to improve the lubrication performance and wear resistance.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2024-0119/

The purpose of this study is to investigate the impact of titanium oxide (TiO₂) filler on the abrasive wear properties of bamboo fiber reinforced epoxy composites (BFRCs) using a Taguchi approach. The study aims to enhance the abrasive wear resistance of these composites by introducing TiO₂ filler as a potential reinforcement, thus contributing to the development of sustainable and environmentally friendly materials.

This study focuses on the fabrication of epoxy/bamboo composites infused with TiO₂ particles within the Wt.% range of 0–8 Wt.% using hand layup techniques. The resulting composites were subjected to wear testing according to ASTM G99-05 standards. Statistical analysis of the wear results was carried out using the Taguchi design of experiments (DOE). Additionally, an analysis of variance (ANOVA) was used to determine the influential control factors impacting the specific wear rate (SWR) and coefficient of friction (COF).

The study illuminates how integrating TiO₂ filler enhances abrasive wear in epoxy/bamboo composites. Statistical analysis of SWR highlights abrasive grit size (grit) as the most influential factor, followed by normal load, Wt.% of TiO₂ and sliding distance. Analysis of the COF identifies normal load as the primary influential factor, followed by grit, Wt.% of TiO₂ and sliding distance. The Taguchi predictive model closely aligns with experimental results, validating its reliability. The morphological study revealed significant differences between the unfilled and TiO₂-filled composites. The inclusion of TiO₂ improved wear resistance, as evidenced by reduced surface damage and wear debris.

This research paper aims to integrate TiO₂ filler and bamboo fibers to create an innovative hybrid composite material. TiO₂ micro and nanoparticles show promise as filler materials, contributing to improved tribological properties of epoxy composites. The utilization of Taguchi’s DOE and ANOVA for statistical analysis provides valuable guidance for academic researchers and practitioners in optimizing control variables, especially in the context of natural fiber reinforced composites.

Industrial drivetrains use wet disk clutches for safe and reliable shifting. Advances over the past decades regarding the formulation of lubricants and the composition of friction materials have led to reliable clutch systems. In this context, the friction behavior is crucial for the correct operation of the clutch. Nevertheless, the friction behavior and its influencing factors are still the object of modern research. The purpose of this study is to investigate how the choice of the steel disk influences the noise vibration and harshness (NVH) behavior of wet industrial clutches.

To investigate the influence of the steel disk on the friction and NVH behavior of industrial wet disk clutches, experimental investigations with relevant friction systems are conducted. These tests are performed at two optimized test rigs, guaranteeing transferable insights. The surface topography of the steel disk and the friction lining are measured for one friction system to identify possible relations between the surface topography and the friction behavior.

The steel disk can influence the friction behavior of wet disk clutches. Using a different steel disk surface finish, corresponding results can show differences in the shudder tendency, leading to a nonfavorable NVH behavior – different gradients of the coefficient of friction over sliding velocity cause this phenomenon.

This work gives novel insights into the friction and NVH behavior of industrial wet disk clutches. It supports engineers in the optimization of modern friction systems.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-02-2024-0054/

The purpose of this study is to look into the hygroscopic and tribo-mechanical properties of a polypropylene/polyamide-6 (PP/PA6) blend and a PP/PA6/Boron sesquioxide composite.

The hygroscopic behaviour of the PP/PA6 blend and PP/PA6/Boron sesquioxide composite was studied using a water contact angle goniometer in this study. To validate the hygroscopic behaviour of the blend and composite, water contact angles and surface energy of the materials were investigated. Tensile strength and hardness tests were used to determine mechanical characteristics, and tribological experiments on a pin-on-disc tribometer were used to demonstrate the friction and wear rates of dry and water-conditioned blends and composites. The melting temperature of dry and water-conditioned composites was determined using DSC analysis.

The hygroscopic effect of the PP/PA6 blend was found to be minimal in the experiment, while it was relatively dominating in the PP/PA6/Boron sesquioxide composite. Tensile strength was found to be somewhat lower in blend and composite compared to virgin PP, whereas hardness was found to be higher in both blend and composite. The composite’s tribological testing findings were fairly outstanding, with the coefficient of friction (COF) and wear rates significantly reduced due to boron sesquioxide reinforcement. The reaction between boron sesquioxide and water molecules produced boric acid, which increased the tribological characteristics of the composite even further. Following 30 days of water conditioning, the weight of the blend increased by 3.64% and the weight of the composite increased by 6.45% as compared to the dry materials. After water conditioning, tensile strength reduced by 0.8% for the blend and 14.16% for the composite. Hardness was determined to be the same in the dry state and after water-conditioning for blend but dropped 1% for composite. As compared to blend, the COF and wear resistance of composite were 15.52% and 25.16% higher, respectively. After absorbing some water, the results increased to 28.57% and 34.9%, respectively.

The mechanical and thermal behaviour of polymer composites (particularly polyamide composites) vary depending on the surrounding environment. Tests were carried out to explore the effect of water treatment on the tribo-mechanical and thermal characteristics of PP/PA6/Boron sesquioxide composite. Water treatment caused polyamides to bind with water molecules, resulting in voids in the material. The interaction between boron sesquioxide and water molecules produced boric acid, which increased the tribological characteristics of the composite.

The purpose of this paper is to improve the mechanical and tribological properties of Si₃N₄ ceramics and to make the application of Si₃N₄ ceramics as tribological materials more extensive.

Si₃N₄-based composite ceramics (SN-2L) containing nitrogen-doped graphene quantum dots (N-GQDs) were prepared by hot press sintering process through adding 2 Wt.% nanolignin as precursor to the Si₃N₄ matrix, and the dry friction and wear behaviors of Si₃N₄-based composite against TC4 disc were performed at the different loads by using pin-on-disc tester.

The friction coefficients and wear rates of SN-2L composite against TC4 were significantly lower than those of the single-phase Si₃N₄ against TC4 at the load range from 15 to 45 N. At higher load of 45 N, SN-2L/TC4 pair presented the lowest friction coefficient of 0.25, and the wear rates of the pins and discs were as low as 1.76 × 10⁻⁶ and 2.59 × 10⁻⁴mm³/N·m. The low friction and wear behavior could be attributed to the detachment of N-GQDs from the ceramic matrix to the worn surface at the load of 30 N or higher, and then an effective lubricating film containing N-GQDs, SiO₂, TiO₂ and Al₂SiO₅ formed in the worn surface. While, at the same test condition, the friction coefficient of the single-phase Si₃N₄ against TC4 was at a range from 0.45 to 0.58. The spalling and cracking morphology formed on the worn surface of single-phase Si3N4, and the wear mechanism was mainly dominated by adhesive and abrasive wear.

Overall, a high-performance green ceramic composite was prepared, and the composite had a good potential for application in engineering tribology fields (such as aerospace bearings).

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2024-0161/

The purpose of this paper is to investigate the friction and wear mechanisms in lubricated sliding conditions of additively manufactured SS316L parts. The different viscous oils 5W30, 15W40, 20W50 and SAE140 are used. These investigations provide a theoretical basis for the high performance of printed and postheattreated SS316L.

Tribological tests were carried out on selective laser melting-made SS316L printed specimens and heat-treated specimens. The parameters in 15 min of test duration are 20 N of load, 200 rpm, 8 mm of pin diameter, 25 mm length, 80 mm of track diameter and EN31 counter disc body. This work presented the phenomena of lubrication regimes and their characterization, as identified by the Stribeck curve, and these regimes affect the tribological properties of additively manufactured SS316L under the influence of industrial viscous lubricants. The results are observed using Scanning electron microscope (SEM), X-ray diffraction (XRD) and wear tests.

The observations indicate that additively manufactured SS316L shows a reduced coefficient of friction (COF) and specific wear rate (SWR). This is credited to the utilization of different viscous lubricants.

This exclusive research demonstrates how various viscous lubricants affect the COF and SWR of printed and post-heat-treated SS316L parts. Lambda (λ), lubricant film thickness (h₀), surface roughness and wear mechanisms are studied and reported.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2024-0110/

The purpose of this paper is to examine the mechanical characteristics and optimization of wear parameters of hybrid (TiO₂ + Y₂O₃) nanoparticles with Al matrix using squeeze casting technique.

The hybrid aluminium matrix nanocomposites (HAMNCs) were fabricated with varying concentrations of titanium oxide (TiO₂) and yttrium oxide (Y₂O₃), from 2.5 to 10 Wt.% in 2.5 Wt.% increments. Dry sliding wear test variables were optimized using the Taguchi method.

The introduction of hybrid nanoparticles in the aluminium (Al) matrix was evenly distributed in contrast to the base matrix. HAMNC6 (5 Wt.% TiO₂ + 5 Wt.% Y₂O₃) reported the maximum enhancement in mechanical properties (tensile strength, flexural strength, impact strength and density) and decrease in porosity% and elongation% among other HAMNCs. The results showed that the optimal combination of parameters to achieve the lowest wear rate was A3B3C1, or 15 N load, 1.5 m/s sliding velocity and 200 m sliding distance. The sliding distance showed the greatest effect on the dry sliding wear rate of HAMNC6 followed by applied load and sliding velocity. The fractured surfaces of the tensile sample showed traces of cracking as well as substantial craters with fine dimples and the wear worn surfaces were caused by abrasion, cracks and delamination of HAMNC6.

Squeeze-cast Al-reinforced hybrid (TiO₂+Y₂O₃) nanoparticles have been investigated for their impact on mechanical properties and optimization of wear parameters.

Additive manufacturing of polymer composites is a transformative technology that leverages the benefits of both composite material and 3D printing to produce highly customizable, lightweight and efficient composites for a wide range of applications.

In this research work, glass fiber-reinforced polylactic acid (PLA) filament is used to print the specimen via fusion deposition modeling process. The process parameters such as infill densities (40%, 50% and 60%) and raster angle/orientations (0°, 45° and 90°) are varied, and the specimens for tensile, flexural, impact, hardness and wear testing are prepared as per their respective ASTM standards.

The results revealed that with an increase in infill density, the mechanical properties of glass fiber-PLA specimens increase progressively. Optimal tensile properties and flexural properties are obtained at 0° and 90° raster angle orientations and 60% infill density. Minimum wear rate is achieved at 0° raster angle orientation and it increases at 45° and 90° raster angle orientations.

Using SEM, the microscopic analysis of the fractured specimen was analyzed to study the interface between the fibers and matrix and it indicates the presence of good adhesion between the layers at 60% infill density and 0° print orientation.

This study examines how different stacking sequences of bamboo and flax fibers, treated with 5% aqueous sodium hydroxide (NaOH) and filled with 6wt% titanium oxide (TiO₂), affect the physical, mechanical and dry sliding wear resistance properties of a hybrid composite.

Composites with different fiber stacking arrangements were developed and tested per American Society for Testing and Materials (ASTM) standards to evaluate physical, mechanical and wear resistance properties, focusing on the impact of flax fiber mats at intermediate and outer layers.

The hybrid composite significantly outperformed composites reinforced solely with bamboo fibers, showing a 65.95% increase in tensile strength, a 53.29% boost in flexural strength and a 91.01% improvement in impact strength. The configuration with multiple layers of flax fiber mat at intermediate and outer levels also demonstrated superior wear resistance.

This study highlights the critical role of stacking order in optimizing the mechanical properties and wear resistance of hybrid composites. The findings provide valuable insights for the design and application of advanced composite materials, particularly in industries requiring high performance and durability.